How to make a handle from the goose pen. How to make a writing handle with your own hands. What can be made of handle

In feather handles, the ink does not allow to pour out atmospheric pressure. If you dial into the straw for water cocktails and clamp one end, the water will be reliably locked in it. But this technology works while pressure is stable. If you get on the plane with such a straw, then after a while, after a take-off, part of the water will turn out, since at a height in the cabin pressure drops by about 25%. In the case of a pepper handle in the area of \u200b\u200bthe pocket, an ink stain would have formed.

The most important part of the non-pepper handle is the feeder - partially or completely hidden under the pen. One or, as in the monblanc handles, two capillary channels, along which the ink come to Peru. The fider's ribs act as a kind of buffer on which the surplus ink accumulates and from which, in the case of an increased ink flow, are reserved. Ink rents are held due to the capillary effect. Despite the seeming simplicity, the solution is very nontrivial, requiring outstanding knowledge of mechanics and physics.

However, for a catastrophe with an ink stain, it is not necessary to take off - quite the usual fluctuation of atmospheric pressure or a small concussion. In order for this not happened, a rather witty solution was invented - feeder with a ribbed collector. All surplus ink due to the capillary effect was detained on the ribs. The feeder performed other functions - the ink came to Peru through the channel, the cross section of which was determined by the speed of their receipt. Since when using the handle, the ink consumption was non-permanent, the collector also performed the role of a kind of buffer.

No less important part of the pen - feather, from its quality and depends comfort when using the instrument and beauty of the letter. The best Montblanc feathers are made from a leaf gold alloy with a variable thickness - from 0.18 mm at the base of the pen up to 0.52 mm in the tip area. It provides a light spring moment, well-known Montblanc owners and enhancing letters comfort. The body of the feather is adjusted, bend, polished, engrave and weld the tip of the solid metal. After that, he gives a certain form corresponding to the style of the letter - from the traditional sphere to the beveled flat tip for calligraphy. In some Montblanc boutiques there are computerized systems that allow you to issue the unique parameters of your style of writing after the test job, which you can choose a suitable feather for you, and with a great desire and budget - to make a unique pen especially for you.

One of the final operations is made by the finest diamond saw. It is this almost invisible cut due to the capillary effect delivers inks to the tip and paper. It remains only to manually polish it and insert into the handle.

We used feather handles in the 19th century, because they are very comfortable. But the vintage handles had one disadvantage: they wrote ink, which were dirty. But if you insert a ball rod into the pen, the handle will be comfortable, and stylish.

To make a ball handle from the poultry pen, you will need an old handle, pen and a little patience.

What a handle is made from

Old ballpoint pen (better than Bic, as they have a thin rod),
- bird feather (goose, swan, peacock, stork or any other),
- scissors,
- Yarn.

How to make a handle

Find the bird's feather. It can be any feather that you are comfortable to hold in your hand. But keep in mind that the best - long feathers from the poultry tail. The greater the pen, the better. Then the handle rod is easier to fit inside.

Always wash feathers found on the street. You can wash the pen under running water, gently removing bugs and dirt from it. It should be beautiful, without flaws.

Disassemble the ballpoint. Get the rod out of it. Cut the tip of the pen with scissors. Try inserting the rod inside. If it is too long, cut off the tip with scissors and again try to insert it into the feather. Well, if there is a little ink in the rod, since then you are not swinging them.

Take the yarn and cut about 50 cm. Put the tip of the yarn from above to the end of the pen, where the rod is inserted, and leave the length of approximately 7 cm. The second, longer end of the yarn, start wrapping around the pen and short end.

Try to wrap as close as possible. When the handle is quite tightly wrapped, make both ends of yarn. The five nodules will be enough. So that the tips are not sticking out, they can be glued to Peru.

The handle is ready.

Other options for ballpoint pen

Instead of braid, you can use glue. Glue should lubricate the feather inside. If the feather is too narrow, it can be cut from the side. Then add super-glue, insert the rod inside the pen and give Peru dry. Instead of glue, you can use the tape, wrapped it around the pen from below, but then the handle will not look so beautiful.

In order for the feather to be more convenient to keep, it can be crazy from the fluff, which is usually attached to the bottom of it. To do this, you can use the usual stationery knife. Peru, if desired, you can give another form using the same tool. Gently spend along the pen with a knife, bottom to up, trying not to break it.

It all depends on personal preferences and from the appearance of the pen. Peacock feathers are so beautiful that it is better to leave them, as it is. That feather was softer, it can be left for a night in the water.

Feather can be painted with hair paint. Drain the paint in the plastic dishes and dip the pen into it several times. Then rinse with water with water.

Many modern people prefer to use ballpoint handles, but there are those who still give preference to grace, clarity and individual style of feathers. Instead of a ball at the end of such a handle, a sharp pen is installed, leaving behind the line of different thickness depending on the pressure on the handle, the speed of the letter and the direction of specific strokes. In addition, the featured handle can be repeatedly filling in ink, so that it can serve you all his life. However, the feat handle is somewhat different, compared to ballpoint handles. When you learn the proper letter of the letter, you will be noticeably easier to write with a pen handle.

Steps

Part 1

Take a handle correctly. Remove the cap from the handle and take it into your main hand, gently climbing between big and index fingers. In this case, the housing of the handle should rely on the middle finger. For the rest of the fingers on the paper to stabilize the position of the hand.

Attach pen pen to paper. It may seem that it is just enough to do, but the design of the pen handle is somewhat more complicated than the ball. Because of the pointed pen, instead of a ball on the end, the pen should be properly applied to the paper so that she could write. This is the so-called optimal position.

Keep the handle firmly. When writing there are two ways to control the handle: fingers or hand in general. When you work with a ballpoint handle, it is quite possible to do with your fingers, since thanks to the ball the handle will write in any position. But the feather handle must be controlled by the entire hand, so as not to miss the optimal position. Therefore, use the recommendations below.

• When the handle is in your hand, keep your fingers and wrist motionlessly, using the hand at the time of your hand to move the handle. First, look for writing in the air, and then on paper to gradually get used to the letter with your entire hand.

1. Easy to press the pen during the letter. There is no need to put it very much to the feathers, however, you should have some pressure on the pen so that ink do. Carefully click on the pen and start exercise to write a feathered handle.

   Part 2

   How to fill in a feathers ink handle

   1. Determine the type of the feat handle. To date, you can find three types of feathers: with cartridges, converters and a built-in piston system. The difference between them lies in the ink supply system and in the method of filling the handle ink, when they end.

      • Currently, the most common feathers with cartridges are most common, as you can change the cartridges easier. For a letter, the handle of this type you will need to buy ready-made cartridges with ink and periodically change them in the handle when the ink is erected.
      • Converter handles are equipped with a reusable cartridge that is inserted inside. They will suit you if you do not have anything against yourself to refuel ink cartridge every time they end.
      • Piston handles are similar to the converter with the exception that they have a built-in refill system, so you do not have to replace the reusable cartridge with a converter purchased separately.

   2. Replace the cartridge in the feat handle. First remove or unscrew the cap from the knob, then unlock its housing. Remove from the inside an empty cartridge. Then follow the steps below with the new cartridge.

      Fill the piston handle. Remove the cap from the pen and, if necessary, an additional cap at the opposite end of the handle that closes the piston mechanism. Scroll the piston position control (usually counterclockwise) so that the piston is located at the writing end of the handle. Then follow the actions below.

      • Fully plunge the pen feather into a jar with ink so that the ink is hidden a hole at the base of the pen.
      • Start twist the piston clockwise to dial ink into the handle.
      • When the ink container is filled, remove the handle from the car with ink. Scroll a little again the piston counterclockwise to slide a few drops of ink back into the jar. This will allow you to get rid of air bubbles.
      • Wipe the feather from the ink with a napkin.

   3. Fill the converter handle. Converters in feathered handles are two types: with a piston mechanism or with a pipette system of refueling. To fill a handle with a pipette system, remove the cap from it, unplug its housing, plunge the pen into the ink, and then follow the steps below.

      • Slowly push the tank for ink and wait when air bubbles will appear on the ink surface.
      • Slowly release the ink tank and wait when it is filled with ink.
      • Repeat the specified actions until the tank is full.

   Part 3.

   How to use feathers for handle

   1. Choose a suitable pen for everyday letter. There are many different types of feathers for ink handles that are intended for use in different situations and to create a variety of effects. For daily letters, stop your choice on:

      • transition with a rounded end leaving after an uniform line;
      • different sizes, writing thin lines;
      • hard rein, halves of which are little diverge to the sides, so that it will not break under pressure when you click on it in an attempt to create more fat lines.

   2. Select feathers for a decorative letter. To write decorative or calligraphic handwriting, you will not fit feathers used for everyday letters. Instead, stop your choice on one of the following options.

In my Soviet past, the following stationery tricks were used very often. I also shortened the rods, changed the writing knots from the pens that had liked, hatched the wrong letter written or the word ...

Here came to these tips in Encyclopedia technologies and techniques . Read, remember childhood? :)

Stand for hand.

Make out of the wire spring stand and write it is much easier. Part of the wire facing the hand is isolated with ribbon. The stand is easily removed and put on hand. Add: This trick does not allow to arrange paper when the hand touches the sheet, as a result of which the ballpoint handle gives interruptions.

Unscrewing tight parts.

When disconnected tight-repeated parts (for example, the housing of the handles), you can use a small piece of grinding skirts.

Adamoplasty to increase the strength of the fingers.

Dried ball rod.

Do not hurry to recharge your ball handle just because the surface of the paste has a stem from the open side and the paste so ceased to flow to the ball. Drip to the rod 2-3 drops of acetone, and then break the needle with a crust. - The handle will again gain its former performance.

Storage rods for ballpoint handles.

The rod of rods for ballpoint handles can be stored in the tube with a dense stopper, without fear that the paste dries. If you are dried in a test tube with fresh rods, they soon restore their properties.

Rod alteration from ballpoint pen.

If your disposal is a sleek rod for ballpoint handles, and you need a rod with a focus for the spring - it does not matter. Heat tweezers and tips on the rod two pins.

How to fix the rod of the ballpoint handles.

You can recharge your like ballpoint handle like this: remove the writing node from the full rod. The rod is inserted into the channel of a one-time ballpoint handle or in a blank rod and the entire length passes a thin wire until it stops into the ball. Then the design put vertically and after a few hours an empty handle or rod will be filled with paste.

Short ball rod.

When you need to recharge the ball handle, and instead of the necessary writing node in length in 107 millimeters there is only a node of 82 millimeters, cut off the segment of a 32 millimeter node from you survived your time and put it on a short knot. And now you can safely insert the knot thus compiled from two parts into my fountain pen.

Treatment of a packing rod.

After repeated refueling of the ballpoint handle, the gap between the edges of the rod and the ball increases and the handle starts writing worse - dirt. This defect will disappear if the end of the rod is clipped. The simplest "crimp" can serve as a stationery button, stuck in a tree. Place the end of the inclined rod into the button angle of the button and, slightly pressing, brighten it.

So that the handle does not leak.

In imported balloons (Hungarian "Pax", American Parker), a branded new-volume writing unit can be replaced by domestic. It is shortened from the back side by 23 mm, the back portion 25-30 mm long is cut off from the used node and a new writing node is collected by a total length of 98 mm.

Perfect ink for handle.

If the fountain pen is caught and refuses, it's most often not in it, but in ink. Having bought ink vial, they need to be filtered through a layer of filter paper and then add a teaspoon of alcohol (can be denaturated or cologne). Here, ink, the handle will write flawlessly.

Take advantage of this advice when you need to refuel the ink fountain. The paper shred will save your hands clean, and then serve as a common material.

Refueling used markers.

Used felt-tipsers will still serve if they are filled with ink. So that the mascara does not dry, store markers need to be stitched without air access, for example, in a vessel with water. Check only if the caps are sufficient enough to the housing.

(True, this advice does not exactly like it - the mascara dries and gets dirty. I felt the markers with simple inks of different colors. You just need to give them a good track - and use on health!).

Multicolor ballpoint pencil with pencil.

In a multicolor ballpoint handle, one of the rods can be replaced with a pencil. From the used rod, you need to pull the writing node and insert a piece of the griffel with a length of 10-15 mm in its place.

Scraper for graphic and retouchers.

A comfortable scraper for graphic and retouchers can be made from a collet pencil and a piece of trapezoidal blade sliced \u200b\u200bin Cangge. The number of sponges of the Tsang should be even, with an odd blade lightly bend.

Match instead of a poster feather.

Those who need to write a large letter header or announcement, can be advised to make inscriptions with a match inserted into the collet pencil.

Feather from the beat.

A piece of elasty with several cuts, fixed in the old brush, becomes an excellent poster feature.

Fountain pen.

Designers-designers are often a featured handle with multi-colored ink and ink for decorating art posters and panels. After a long work, such a handle, the pen starts scratching and cling paper. To correct this defect, take a small piece of fine-grained emery paper - "zero", and on it with pressure (not large than it is required for the letter) Make a dozen double handle with a dozen handle. The feather will stick away and write well. Save emery paper, it will come in handy more than once.

Prevention of steel feathers.

All writing is well known how quickly steel feathers are energized in ink and deteriorate even when each time they are carefully wiped. Meanwhile, there is a very simple way to continuous preservation of feathers. New feathers are immersed as half an hour into a solution of copper sulfate; Then they are taken out so that they remain wet, and give them to dry. Thus-processed steel parts and feathers are not rust and not corrosive ink.

In addition to the specified method, there is another, highly simple way to continuously preserve steel feathers, which is that the pen after the letter is sticking to the crude potato and leave it there until the next use. Alkaline potato juice weakens the oxidizing effect of the ink on the pen and completely protects the latter from damage.

Removal of blots from the drawing.

To remove the blots from the drawing, erase it with ink eraser, stitch this place with a soft pencil and again spend the line. On the graphite, the mascara is not blown away. After drying, the erase pencil is a soft eraser.

Removing carcass from the drawing.

You can remove the mascara from the drawing in this way: to clean the defective place in small sandpaper, and then the finest skin is "zero". Next to post the eraser and polish the smooth solid object. Paper at the same time fully retains its drawing qualities.

Maski cleaner with glass fragment.

Sleep the mascara in the drawing with a fragment of the glass of the blurred light bulb much better than the brothe blade.

How to bring fatty stains on paper.

Luggage magnesia is mixed with such a number of absolutely pure gasoline so that the grainy mass is formed. A small amount of this mass is gently rubbed a fat stain with a finger, then small grapplets of magnesia are removed from paper. Fresh fat stains usually disappear immediately, and the solar stains are removed during repeated rubbing.

Neat removal of lines.

A small piece of gum, clamped in a raysfedera, easy to remove a pencil line from the drawing, not touched on the other, closely from her.

Taken from the section, "Encyclopedia of Technologies and Methods" Plukh V.V. 1993-2007

Make a beautiful simple handle and make it original - easy. The most original ideas that can only come to mind.
To make a beautiful handle you need to take the handle itself, the material for the decor and glue. You can decorate, wrapped with a narrow satin ribbon, attach to the top edge of a flower or a bow of paper or fabric. Get the original designer thing. Such a handle can be an interesting gift made with a soul.

The idea of \u200b\u200bshaking the handle with multi-colored threads on the technique of Macrame, and even with the original weaving - a gorgeous version for a stylish girl.

You can decorate your handle as you like any beautiful things, rubber bands, stickers, feathers, rhinestones. Everyone you want.

What can be made of handle

Ballpoint handle case can serve as a material for different crafts.

• You can make the original stand for a mobile phone. For this, you will need four or five handles and gums for money. Twist three handles with a rubber band so that it turns out to be a steady tripod. Turn the horizontally one or two knobs horizontally to two legs, depending on the thickness of the phone. Install the resulting design slightly under the tilt and put a smartphone on it. Viewing video is very comfortable and hands free.
• From the handle and four simple pencils can be made. From the pencils with the help of rubber bands collect the base in the form of the letter "T". Attach the old handle at the bottom of the letter. The feed function will perform an elastic band. Old empty rods can be used as arrows. Here is a toy for boys ready.
  Many, probably, remember multi-tiered chandeliers with transparent plastic suspensions.
• By the same principle you can do. You need a circle plastic fixed on the lamp, and many multicolored transparent enclosures from the handles. Stationery is fixed in a circle with wire or clips. When the lamp is turned on, the lamp will look like a crystal, and disperse a multicolored light.

How to make a handle with your own hands

How to make a 3D handle with your own hands

Such a handle can be made it from a conventional adhesive gun. To begin with, it is necessary to disassemble and remove the pushing mechanism, the lower part of the pistol handle is better to sprinkle. Then you need to reduce the outlet. You can shove the clips there and climb it to not fall. The next step you need to attach a mini fan, such available in different devices and sold in stores as spare parts. Small crocodiles are attached to the fan wiring, we will use them to connect the battery. Now you need to fix the Crohn battery on the bottom of the gun. To secure all parts, use plastic clamps and glue. That's all - 3D handle do it yourself ready. You can try to draw.

For the feat handle you need a pen itself. You can take turkey or goose, they are large. Paint with dyes in any color you need. You can immediately in several colors. Feather cover above the base must be removed to be more convenient to keep when writing. A sharp knife to cut down the bottom of the pen under the cone. She is very firm and the resulting edge can be written.

You can also use a calligraphic pen. It must be attached to the turkey prepared Peru, and the junction place to reorganize. Made in this way, the writer will be more durable.

Gel handle do it yourself

• The gel handle can be done, as well as simple. Any materials can be used as a core for a rod. Only insert the gel rod into the made flask.
• Gel handle - aquarium, a very interesting option and a rod can be changed. For the manufacture you will need a transparent flask with a wooden cork. In traffic jam, we make a hole in the size of the gel rod. Cork, if you wish, you can paint. In the flask we pour water and add glycerin. The more glycerol will be, the slower will float the decor inside. I fill in the flask filled with liquid, different sparkles, asterisks and mandatory foil fish. Insert the rod into the plug and close it the flask. Handle - aquarium is ready.

How to make a paper handle

Made of paper handle can be the most diverse coloring. For its manufacture you will need a sheet A4 and a rod. Cutting a piece of sheet at an angle to when you twist the rod, it turned out a bevelled nose. Take the rod, we wash the glue when it sticks tightly, we begin to twist tightly. At the end, we scroll with glue. You can paint the handle as you like. You can draw various patterns. Be sure to handle will be covered with varnish so that the paper does not rub in the process.

The rod in such a handle will not change. Started, make a new handle.

How to make a pencil handle

To create two in one handle and pencil you will need a handle, a simple pencil. Disassemble the handle. From the pencil cut off half, it is possible less. Now you need to insert a part of the pencil into the handle housing. It naturally does not fit there, so it needs to fasten it a stationery knife. Painted pencil and took it hard with a tape. Now cut the rod from the handle to insert it into place and collect a handle. Now you do not need to look for a pencil in order to draw something, it will always have you from the back of the handle that you write.
The remaining part of the pencil does not throw away, it will come in handy you next time.

How to make an invisible handle

To make an invisible handle, you need to do to start. Make such ink at home is not difficult. In order to need a diluted solution of copper mood. He has a slightly bluish tint if they write something to them, it will not be seen. To read such a letter, you can, holding the paper over the ammonia alcohol.
Writing with such inks will have to use a feather handle, as they will not turn them into the rod. And if someone succeeds to do this, they will still flow, because very liquid.
Spy ink can be made from lemon juice, they manifest themselves if the letter heavily heat the iron.

What to do to write the pen

If suddenly you have stopped writing the handle, and the ink still needs to do the following.

1. Disassemble the handle to pull the writing tip and pour from the other end. Perhaps there were simply air bubbles.
2. Without viewing the handle from the end, which they write, the suction movement pull the ink on itself. It also helps well, and you will not get dirty.
3. You can simply raise on the writing tip, perhaps ink a little thickened. From warm breathing, they will become fat.
4. A radical solution is to replace the rod, he could be defective.