How to change the mixer for the bathroom with a shower. How to replace the mixer in the bathroom with your own hands. Stages of installing new equipment

The mixer is an important detail of the bathroom, good when he is high quality and for a long time, but always comes the day when the service life of the old plumbing is coming to an end and replacing the mixer in the bathroom. You should not immediately cause plumbing, install the mixer in the bathroom yourself, if you follow the instructions below.

Which device to choose

First you need to choose a new one that it serves as long as possible. The new device can be bought in both the usual economic departments of shopping centers and specialized stores of plumbing.

Before buying a mixer, see how it connects to the water supply network. It is also worth remembering, the cheap plumbing will not last long, and some details can be broken at the time of installation. Quality materials of the road, but also the quality of purchase will be significantly higher. It is best to choose plumbing from brass or stainless steel, these metals are the most racks to corrosion.
In addition to the material, pay attention to the weight of the mixer. Operation of any mixer directly depends on the thickness of the metal, so it's not too easy to take a lightweight. A high-quality mixer weighs a lot.

When choosing a mixer, learn its characteristics better. The device must approach the place where you install it. Think in advance whether you want a crane or lever, as well as be sure to take into account the length of the water tube, if there is a need for the use of the mixer not only in the bathroom itself, but also in the sink.

How to remove the old mixer

How to change the mixer in the bathroom with your own hands? First you need to dismantle the old one. It's easy to do it, but first overcoat the water in the riser. If you have a column, a boiler or a boiler, separate the water and from them separately. To remove the old instrument, you will need PASSATIA and an adjustable key.

Drain from the crane the remaining water in it, after this procedure, start unscrew it. Do it carefully and not in a hurry, otherwise you can accidentally damage the thread on the fitting.

It will be very unpleasant, because if the thread comes into disrepair, you have to disassemble the wall to replace the unsuitful fitting to the new one. As soon as you remove the old device, clean the fitting from the fact that it remains paints or winding.

How is the mixer replacement in the bathroom

Before replacing the mixer in the bathroom with your own hands, check the presence of all components. Here are some details must be in full:

Main unit;
Shower canoe;
Shower hose;
Gander;
Eccentrics;
Decorative plaffones;

Each item must be in a separate cellophane or tissue packaging. Make sure that the carving on the mounting nuts and the eccentrics is not damaged. Best of all, of course, do it before buying.

Step-by-step instruction

So, as soon as you blocked the water and removed the old equipment, then it will happen in this way:

Unscrew the plans remaining from the old appliance eccentric. Wash the pliers are needed strictly counterclockwise.
Now the skill of the installation of new eccentrics into the pipe. Before installing, wrap their base with flax (or fum-ribbon), for this tissue strip, screw to eccentric to the very end, starting from the base, and back.

The end of the strip firmly secure. As soon as you cover the luna with lubricant, the eccentric can be twisted into the pipe with an adjustable key. Before twisting the eccentric, clean the pipe with dirt from pollution.
Screw to the eccentric reflectors, they close the pipe.
Manually screw the block to the eccentrics, and then pull the nuts with the adjustable key.

Watch that all the details sat tightly and did not hang out. At the last stage, the hussak or shower hose remains.

After all necessary works, connect water. If there are places of leakage, just pull them out.

Installing the mixer on the sink

Sometimes in the bathroom there is not enough single mixer, if the sink and bath are supplied far from each other. In this case, the installation of a separate device is required. So how to install the mixer on the sink in the bathroom?
Tools that you need to install:

Adjustable key;
Screwdriver;
Passatia;
Lon or Fuma tape.

Installation Instructions:

First disconnect the water. After that, disconnect the eyeliner of the old instrument from the cold and hot water pipes, clean the thread.
Small key or passatages, unscrew the fitting nut of the mixer, it is at the bottom of the shell. The mixer on the sink is usually attached with 1 or 2 mounting studs, clamping nuts are screwed on them. Unscrew these nuts and remove the old device.
Collect a new mixer before it is installed on the sink. Carefully screw into it, try not to damage the cuffs on the fittings, the rubber may not withstand too strong clamp.

Screw the new mounting studs into the bottom of the mixer, then install the sealing ring.
Slide hoses Clean through a hole in the sink, the crane himself will rise on its place.

Install on each stud on the clamping washer with a rubber lining. After that, screw the nuts on the hairpins and tighten them with a stronger - the mixer should not rotate or stagger.
At the cold and hot water pipes, attach a flexible eyeliner, it will be the last stage of the assembly. Screw the nuts on the threads of the pipes using the flax or fum-tape, but be careful, do not drag too much, otherwise the sealing tires damage.

As soon as you attached the wiring, you can let water. Check the presence of leaks, the cold water first, and then hot.

As you can see, the question of how to make a mixer in the bathroom, is solved quickly and without assistance. Choose instruments from high-quality and long-term materials, follow all installation instructions, and then the mixers will serve as longer as possible.

If, due to some reasons - breakdowns, wear, design shift, it is required to replace the mixer in the bathroom or kitchen, then for the owner this case should not be an unexpected and extraordinary event. Independent replacement of the water tap - simple work, requiring only the attentiveness and availability of a suitable tool. At my home Clello, such work occupies a maximum of 1.5 hours, not counting the time of choice and acquiring the desired plumbing device in the trading network.

Features

Any plumbing equipment of the apartment enters the system of common to the home or area of \u200b\u200bwater supply and plumbing communications. Therefore, you need to remember responsibility for errors in independent repair or replacement of this equipment. They can lead to the damage of the property of neighbors and the management company as a result of flooding, fire or other incidents that have arisen because of a negligence attitude towards their actions of the culprit of the accident. In total, you can avoid if before starting work to thoroughly think over the whole process of replacing the mixer.

Before starting the repair or replacement of water reinforcement (valves, valves, cranes, mixers) and devices for their connections with pipelines, it is necessary to completely turn off the water supply to the repaired area. For this, shutting down fittings on the commissioning of pipelines into the house or apartment (specialists call such reinforcement primary valves or primary valves).

Replacing or repairing the mixer requires a disconnection of two pipes supplying pipelines - cold and hot water. In addition to disconnecting pipelines, you need to make sure the density of the primary fittings, opening all the cranes on the disabled area: the termination of the leaks from the cranes confirms the lack of skips of primary cranes.

Preliminary measures are needed to ensure complete safety of work. If it turns out that the primary valves in the "closed" position passes water in large quantities, then permission should be permitted to disconnect the valves on the entrance or even at the entrance to the whole house. Permission can be obtained in the management company where you need to write a statement indicating the date and time of the alleged repair.

The management company must send to the operation of shutdown and the subsequent connection of the pipelines of its employees.

Views

To replace a non-unusted or non-primable mixer, you must first purchase a new one. There is a huge number of bath faucets and sinks of domestic and foreign manufacturers, any color, style and manufacturing material.

The device of modern bathrooms involves the installation of mixers of two functional species in several options.

Two separate mixers: one is installed above the shell bowl, the other - for filling the bath and soul. These devices are completely different in design and functions. Over the sink valve crane, intended for washing. The tap over the bathroom has a flow direction switch to a shower or a hussac for a water set.
One mixer performing three functions at once: washbasin over a sink, a device for a set of water in the bathroom and a shower. The same type of mixing crane is used as in the first embodiment (with the direction of the water flow direction).

For the sink, conventional taps with two valves are more often used (one valve for starting cold, and the other - hot water) or taps with one lever. Cranes with a lever are also called one-tech. The device of the name mixers is not equally. They differ in the convenience of use: to control the pressure and water temperature through a single-dimensional crane is enough control of one hand. In the two-tier, sometimes two hands turn out to be a little.

Familiar to everyone at visits to public places (theaters, cinemas, restaurants, cafes, stations) Contactless mixers are not only a new type of sanitary comfort on the principles of automation and electronics, but also enough hygienic and economical devices.

Configuring them to a certain water supply temperature suitable for all family members, they are no longer touched by dirty or soap-made hands.

There are no problems with the forgetfulness of turning off the crane - the sensor in the absence of a "wash object" will block the flow of water. But such faucences of the house are repaired problematic due to the complexity of the sensory system, and in user terms they are only suitable for installation over a washbasin in the bathroom. In other places, they are completely inappropriate: the bathroom is possible to dial, only constantly holding hands under the crane, and in the kitchen they are uncomfortable in terms of frequent change of water temperature when washing and rinsing dishes.

Single-grazing mixers also have a significant disadvantage - they are built in either the ball, or cartridge locking mechanisms, very demanding on the purity of water. In the conditions of old water supply networks that are not equipped with modern sewage equipment, ceramic parts of the cranes quickly fail. The repair details are not subject to, they can only be replaced with a new locking mechanism. But you can cope with such work in 20 minutes without resorting to the services of Plumbers. It is important in this case a set of the desired tool.

Causes of breakdown

The main reasons for the complete replacement of mixing cranes in the kitchen and the bathroom are their frequent leaks or blockages, the wear of switching mechanisms in the Soul-Split system, cracks in the housing, disruption of fasteners, as well as the change of room design, where these cranes are installed. It is necessary to understand and accurately determine why breakdowns occur. Especially this is important for those who are arranged existing mixers, and extra costs are not included in plans.

Often some of the names can be eliminated without replacing the entire crane.

The leaks in the two-fledged types of cranes are from the hussak of the mixer and from under the flywheel of the crane.

From the hussak of the mixer. One of two reasons or both are possible. The first is the skipping of valve gasket due to violations of their integrity, wear, solidification or deformation. Integrity disorder can occur as a result of the impact on the strip of sharp edges of the crane saddle. The second is the wear of the saddle and the valve, which happens most often in cranes with a long time of use as a result of corrosion and mechanical (drone) water effects.
From under the crane flywheel. This is to blame: a seal of the flywheel rod or a valve laying. The reason for a bad flywheel seal is a loose or deformed sealing ring. The reason for the skipping of the gasket - it fell out of the pint.

Ball or cartridge mixers give leakage in cases of sandbanks or other garbage in the shutter mechanism (between the ball and its socket in the ball mixers, and between the cartridge type shutter disks). Even with a dense closure of the cranes, the water will be cooked through the resulting clearance between the work details of the shutters.

In the cranes with the shower, in addition to the listed faults for the same type of mixers, other leaks are possible.

When the crane is opened, water flows through the hussak, and through the shower. The reason lies in the switch. Depending on the type of mechanism, it can be: a lack of water pressure for tight switching of the "shower-shower" system in keypad types of switches with a metal valve, depreciation of guide parts in switches with an eccentric and barrel, breakdown due to sand plates and locks in ball switches, wear of gaskets in spool devices.
The leak through the button of the button switches as a result of damage to the ring gland.

The reason for reducing the flow of water at the outlet of any type of mixers is most often clogging at the end of the hussac of a special device called a aerator. It is contaminated due to the high rigidity of raw water, the deposition of the salts of which is clogged by the aerator grid and the holes of the shower head. Sorry and scale in plumbing pipes can cause clogging of the mixers themselves, which will also affect the power of the jet at the exit of the crane. All of these faults do not require complete replacement of cranes and eliminate easily at home.

The breakdown in the form of cracks and fistulas in the enmallite housings, damage to the fasteners, made jointly with the cranes enclosures, require replacement for good apparatus. Contactless cranes, although they are distinguished by a long service life, are subject to the same faults as everyone else: clogged from dirty water, the internal shutter mechanisms wear out, the aerator grids are clogged. But in addition, sensors and photo cells that are responsible for the inclusion of water can be failed to approach the arms of the tap. Such a malfunction will be asset only by a specialist versed in electronics.

Required tools

When replacing mixing water taps, a small set of tools is required, which will always be found in a person who can solve economic problems independently.

Here is a list of tools, the need for which may occur when dismantling and mounting cranes of different types (without repair):

a multi-sized adjustable or gas key (ideal to have a clamping key);
horn keys on 10, 11, 12, 13, 14, 22 and 24 mm (rarely - key on 27);
end tubular key by 10 mm;
pliers;
scissors;
flat twig thin;
cross-shaped screwdriver;
bucket (pelvis) for draining water.

In addition to the tool, you will need consumables:

tape for sealing connecting parts (thread sealing);
liquid sealant;
insulating tape.

Connecting plumbing hoses must be changed to new ones. New cranes are supplied to the trading network complete with hoses, but their length does not always correspond to the real length at the installation site. Therefore, it is recommended to measure the length of old hoses and acquire the same. The standard length of the hoses from the set with the cranes is 30 cm.

How to remove and disassemble?

Before installing a new crane, it is necessary to dismantle the old plumbing device. It is easiest to remove the mixer for the bath, as it is removed entirely by unscrewing two capel nuts connecting it with the supply pipelines of hot and cold water. The only difficulty may occur in the case of pipelines from polymers. When unscrewed nuts, considerable effort will be required, so you need to hold underwater pipes to avoid their twisting and fault. You can hold the pipes with a gas or clamping key for the metal fastening tips perplexed in them.

Shell mixers remove so quickly, work is often associated with the difficulty of accessing dismantling sites, and sometimes requires the removal of the bowl.

Most modern cranes for shells will be right in the following order.

Water pipelines are disconnected by primary shutdown reinforcement at the apartment reservoir or at home.
Cranes are opening both at the place of work and in other places for removing from disconnected pressure sections. Under an open dismantled crane, if necessary, you can substitute a bucket for collecting fluid residues on the supply of hot and cold water lines.
After making sure that all the water from the pipes at the level of the cranes suede, you can start working on the removal of the mixer of the sink. To do this, have to climb under the bowl by checking anything to not disappear. Sewer pipes and siphon is better to disconnect - it will be more convenient to engage in a crane. To collect possible residues of fluid in disconnected sewer devices, it is well used to use a bucket or pelvis.
Reference flexible wiring from hot and cold water pipes. In the hoses and pipes at the lower level there is still water, it will not hurt to substitute the dishes for her collection. At this stage, you need an adjustable or horn key 22x24.
Immediately a suitable tool (knife, screwdriver) you need to clean the fittings of the supply pipes from the remains of the old sealant, if any.
The next operation is the hardest, especially if the crane has been set for a long time. The lower fastener of the crane has two long steel pins with nuts winding on them. From moisture, the nuts become tightly supposed to the pins, and sometimes it is impossible to unscrew them. To facilitate the task, it is recommended to lubricate all the threads of the pins and the places of their contact with the kerosene nuts or a special solution sold in the equipment stores, and give some time to open the flaps of the compounds. After that, unscrew the nuts with a fully tubular key to 10 (it will come true and the challenge key).
Now it's time to raise the floor from under the sink. Having stretched out as far as possible the faucet outside, unscrew the flexible liners from the inlets at the bottom of the crane case. This can be done with the help of pliers.
Pull the entire crane. Before unscrewing the hoses, this can not be done - the lower fastener plate interferes, through the holes of which do not pass nuts of flexible eyeliner, connecting eyeliners with pipelines.
Clean the installation site of the mixer on the sink from dirt not only from above, but also from the bottom, under the sink.

Recommended cranes not to throw away, but to disassemble on parts. No one knows when gaskets, fasteners, valves and crane boxes may be required. Let even old. Sometimes conventional lambs may be needed, and at hand it will not be.

The knob (lever) of the crane or flywheel is removed after unscrewing the screw with scuffers. Screws are under decorative caps that you just need to pose with a knife or flat scold. After removing the flywheel or lever, unscrew the top cover of the body of the valve mixer or remove the cartridge with cassettes and discs in ball valves. From the body of the valve cranes is easily removed by the other parts: valves, gaskets, crown (crane-box). All this can be very useful in the future.

How to change the crane?

A new crane is installed in the place in the reverse order. Typically, the mixers are supplied assembled. Only in the device of the Soul-Spit system, installed above the bathroom, the shower column hose is placed in a separate packaging. It is connected after mounting the crane to the supply pipes - it is so convenient to work. But check the instruments on the course of the valves and the hermetic reliability of all connecting parts must be required.

Installation of faucets for the kitchen and washbasin in the bathroom is done with their own hands, without attracting professionals. You just need to strictly follow the next step-by-step instructions.

Screw flexible liners to the case. They first need to be consistently skipped through special holes in the rubber seal and the fastener plate with a narrow connecting end of a liner (without nuts) forward, and then lower the shelves to the mounting hole of the shell. For this you have to climb under the sink.
Reliable screw the flexible wiring into the mixer body.
Install the gasket and the mounting plate on the pins below the hole (work under the sink) and tighten them with nuts.
Connect the free ends of the flexible supply to the pipelines of hot and cold water, wound on the thread of adapters sealing tape. Make sure the gaskets are inserted in the nuts of the flexible hose. If they are not, then they must be included. In synthetic pipelines, it is not necessary to apply for tightening nuts of excessive effort.
Proper a crane in the mounting hole of the washing, evenly distributed around the circumference of the upper seal, and tighten the fastener nuts under the sink.
Press the water supply system to the mixer, having previously closed the control cranes that opened before work.
In case of disarming the bowl for accessing the mixer fastener, it must be installed in place after tightening the fastener elements of the crane before connecting flexible hoses to the pipelines. That is, paragraph 3 of the step-by-step instruction is replaced by clause 5, after which you need to suspend the bowl onto its fastener bolts.

Create a task on YouDo if you want to replace the mixer. The site registered private locks and specialized companies in Moscow, performing any plumbing work at competitive prices.

Apply for the artist's search, indicating that you want to call the plumbing to the house. The masters will read the task and offer you qualified assistance in the repair of mixers.

Stages of installing new equipment

After placing the order and coordination with a specialist convenient call time for you, the wizard will come to provide plumbing services and correctly connect the equipment. Installation of a new turnkey mixer is made in several stages:

dismantling of the old equipment in which there was a breakdown
preparation of space for construction
fastening plumbing
connecting hoses to the body of the part
connection to the water supply system

Upon completion of the installation, experts test the system to ensure that the equipment works properly.

Youdo performers will install a mixer on the sink (in the bathroom or in the kitchen), a shower cabin. Experts provide a wide range of additional services - can change faulty gaskets, valves, clean and eliminate breakdowns in the siphon and spend other work in homes and apartments.

Thanks to the absence of intermediaries between you and the master, you can directly ask how much the mixer is worth installing, and what time it will be possible to perform the task.

Duration of sanitary work

The mechanic disassembled in the installation of the equipment, so that they can urgently change the mixer in the bathroom and connect a new design to the water supply system.

Specialists are ready to promptly assist - professionally remove the old faulty item and install a new one in your home or apartment. The installation time depends on the following circumstances:

need to dismantle the old broken plumbing
category of mounting complexity and type of mixer to connect
masters experience

All Youdo performers seek to reduce your expectation, urgently changing the broken valve to new "Christmas trees" or "watering cannon." In the interests of the masters - to leave you a good impression of work. From the number of customers who arranged the quality of services, the Contractor rating directly.

Mounting price formation

YouDo performers offer cheap to change the crane in the bathroom - the price is calculated individually. The mixer itself can be of any type - a two-way or one-tech, simple, with a shower and a thermostat.

The cost of the wizard form such factors:

consumables costs
availability of old plumbing required to dismantle
individual pricing performer

How much is the installation of a mixer with a siphon on washbasins, a bidet, in shower cabins, a specialist will say after evaluating the scope of work.

Agree on tariffs with a specialist, calling the amount that you are willing to pay for the challenge. The wizard will take into account your wishes and offer the best conditions for installing mixers.

Advantages of order on Youdo

Trust the installation of the crane in the sink or bath to a qualified wizard. Fixers registered on Youdo are ready to professionally and cheap mixers of any type - "Christmas trees" or with shower canes, in a bath or on a washbasin. Specify how much it costs to change the crane in the bathroom, and order performers services.

When ordering services on YouDo, you get many advantages:

application application in online mode, saving time to search for verified companies in Moscow
convenient call time
qualitatively replaced plumbing with fastening and connected in the bathroom or in the kitchen

Artists Youdo professionally dismantle the faucet faucet in the sink, bath or washbasin. Our wizards can replace a high-level turnkey mixer and specified deadlines.

The kitchen faucet refers to the most intensely used plumbing equipment. Anyone, even the highest quality similar device, over time requires a certain service - replacing the leaking cartridge or loosely closing bucks. However, it also happens that the housing itself comes into disrepair - the irreversible processes of the surface erosion begin with the constant exposure of the water, the thread in the jacks for the valves or the cartridge begins, the chrome coating is erased. And if the product is from a poorly quality silumin, it is quite possible to complete the case of the body with the appearance of cracks and the pumping of fragments.

Maybe not such a fatal situation - just the owners decided to update the kitchen interior, and without installing new modern plumbing in this matter, too, do not do. It was told in a special article of our portal. Now it will be about how to change the mixer in the kitchen independently, without resorting to the call of a specialist.

This process , although and very responsible, but still quite affordable for the usual owner of the apartment.

What will be required for work

To work on replacing the mixer, you need to immediately prepare the necessary components, accessories, tools, consumables.

We proceed from the fact that the mixer is already purchased. However, it is necessary to check whether the length of flexible hoses that are included are sufficient. As a rule, those that go in the set are only 300 mm, which can be clearly not enough. In addition, if the mixer is not "branded", then the quality of these sleeves in a metal braid usually leaves much to be desired, and they should be replaced immediately.

When choosing and acquiring such hoses, you must pay attention to the fact that the length of their fitting (otherwise it is often called a needle) should be different - this will facilitate the assembly, since the hexagons turn a turnkey will not interfere with each other.

In addition, it is necessary to correctly select the type of threaded connection with a plumbing pipe. This also applies to the diameter and the type of threaded part ("dad" or "mother"). Most often, of course, the "Mom" hoses are used with a ½ inches nut - for direct connection in the appropriate pipe. Nevertheless, options are possible, for example, if the collector's comb is installed or a ball valve with the output "Mom".

Hoses should not be located in tension, in tension, but should not be purchased with a very large length of length. When pressure drops (opening and closing the crane), they will twitch, vibrate, and this causes a rapid wear of the rubber tube placed under the steel braid. She begins to scatter and may in the near future give to flow.

Schematically - the device of the flexible hose in the braid

More durable and reliable in this respect - corrugated stainless hoses.

Of course, they are more expensive, and they are somewhat more complicated to mount them. But in such hoses, excellent stiffness - they will keep the bending attached when installed.

Some masters prefer to do flexible hoses, making the water supply to the mixer made of metal-plastic pipe. To do this, you need to purchase a set of pieces of ultrasters with fittings under the metal plastic.

Such a lining, of course, is also more difficult to perform than with flexible sleeves, but once mounted such pipes, it will be possible to continue for this plot.

Video: How to pick up really high-quality hoses

Of the tools for work, you will need:

- Spanners. The key to 10 and 22 × 24 will be guaranteed. Very often the fastening nuts on the studs require a key to 11. If the mixer is attached to the washing of a large diameter nut, then it is better to prepare an adjustable key.

- Screwdrivers with direct and curly tip.

- Pliers.

- In some cases, do not do without a gas key.

- If the installation will be made on a new sink, on which there is still no hole, or on the tabletop, the electric drill is required with the corresponding crowns (usually with a diameter of 35 mm).

- To work in conditions with insufficient illumination, under the sink, the illumination will most likely need a flashlight.

Materials may require:

- Sealers for threaded connections. They will be needed when there is a need for mounting on the clutch, adapter, adapter, searches for metal-plastic, and the like. You should not trust the fum-tape - it is better to use conventional linen palaces and sealing paste (type "Unipak") - such a connection will be guaranteed from leakage.

- If the installation of the mixer is carried out with temporary dismantling of the washing, then it is necessary to prepare a silicone sealant and, of course, the syringe for the convenience of applying it.

- There may be situations where the old "accurate" threaded connections will not be disassembered. Can help in this case pulbelizer The balloon of the universal lubrication composition "WD-40".

After everything is prepared, you can proceed to further actions.

Prices for popular models of mixers

Mixers

Dismantling of the old mixer and preparatory work

Before proceeding to work directly under the kitchen sink, it is necessary first of all, turn off the feed and cold, and hot water. For this, the valves are overlapped at the entrance to the apartment, or if it is provided for by the internal layout system - overlapping water supply from the collector to the kitchen. Sometimes cranes are installed directly under the sink. Of course, theoretically you can only cover them. However, practice shows that when carrying out work in a close space, it is not eliminated by the likelihood of a random opening of a ball crane with an awkward movement of a hand or elbow. To prevent such misunderstandings, it is better to overlap the water supply to the kitchen completely.
After the valves are blocked, the valve should be opened on the mixer - it normalizes the pressure in the pipe. For a plot of connecting old hoses, it is necessary to substitute a basin or other capacity of suitable dimensions. The hoses are twisted, it is possible to exit water remaining in pipes.
Now you need to remove the old one. This is not such a simple, as it may seem at first glance.

- First, working in an uncomfortable posture, in a very cramped space, lying on the back - it is very difficult, especially if the washing is embedded in the kitchen cabinet.

- Secondly, the "classic" layout of the mixer is between the wall and the washing bowl. In such a narrow niche, I do a wrench very difficult - there is simply no place for its imposition and turn.

- Thirdly, almost certainly all the connections from time and dampness crowned, "baked" and so simply will not fall.

In numerous Internet articles on the replacement of the mixer, this stage, sometimes, is described by casual, such as the "Unscrew the pin with a screwdriver and pull the mixer." Experienced masters know the price of such allegations - with a very large share of probability, these most studs do not agree with a screwdriver, rather - the rusted slot will cut down. So, it will take the key, but about the "convenience" of working with it under these conditions already mentioned.

Which exit? If it is possible to remove the sink (and this feature is in the vast majority), it means that it is not necessary to fluctuate - and dismantling, and the subsequent installation of the mixer will be performed and faster and much better. It is better to spend a very minor amount for the purchase of sealant and hold enough simple actions to remove the washing and its subsequent installation in place - in the end you will still be in winning.

To dismantle the sink, of course, it will be necessary to disconnect it from sewage. You can remove a flexible corrugated hose from the sewer pipe, or, which is probably more convenient for further work, simply unscrew the locking ring on the siphon and remove this "glass" from the drain nozzle of the sink.
Now, conveniently sitting on, it will be easy to remove the spent naught Mixer. On the dependence on its design or a large lock nut, or studs are twisted. It may take to sprinkle these "WD-40" nodes so that they succumb to. There are situations when it does not help - then there will have to use radical measures - cut off with a hacksaw or grinding. The main thing about this is not to damage the sink.

To cutting with grinding, sometimes you have to resort when replacing the old-type mixer installed on the rigid supply of steel pipes.

Disassemble the rusted Signs or a multi-layer paint-covered - extremely hard. Therefore, it is more profitable to simply cut out of the above threaded part. Further - by circumstances. If you manage to free the high-quality threaded nozzle for further addition of the flexible hose - then the question is simplified. If not, then, apparently, you will also have to cut the thread with Lerka.

In order not to postpone on the case, it is necessary to immediately conduct a revision of the state suitable in the washing of water pipes, in particular, those threaded sites on which flexible hoses are planned to be screwed. In order that the laying of the hose felt tightly to the trough of the pipe, it should be even over the entire circumference, not to have sharp or protruding edges, geometry disorders due to corrosion exposure. If there are doubts - it is better to "pack" in this place a threaded factory extension driver - this will guarantee the reliability of the compound with the hose.

It is advisable to "update" the thread on the pipes by installing such extension cords

Installation is carried out on the pass, the fibers of which are turned on the thread on the pipe clockwise, and then wake up the sealing paste. The extension is spinning with a horkin or gas key until it stops.

If you wish and the availability of funds, you can immediately install locking valves if they have not previously stood. This will subsequently carry out any repair work in the kitchen, for example, when an emergency occurs, without turning off the overall water supply network.
In the event that it is planned to carry out water supply with metal-plastic pipes, it is the meaning of CP AZU "Package" on the steel pipes transition fittings.
If it is assumed to install a new mixer on the old sink, then it is necessary to carefully clean the area around the mounting hole from the scale of scale, which accumulated dirt, traces of rust, and the like. Such cleaning is carried out with facial and bottom.
In the case when it is planned to install a new sink, it is necessary, of course, to immediately try to purchase such that already has the installation hole. However, some models are not equipped with them, and have to take appropriate measures.

If the washing is made of stainless steel, then for this use a special tool that cuts perfectly smooth holes in metal with a thickness of up to 1 mm.

The diameter is selected, based on the model of the mixer. So, if it is attached to the hairpins, it will be enough 28 or 32 mm. When mounting on the nut, the hole is necessary with a diameter of 35 mm.

The cutting process is low

It is easy for them - a hole with a diameter of 8 mm is drilled in the intended place. The device is inserted into the cutting part of the bottom, twisted with a bolt so that the cutting edges firmly lay down to the metal. Then, turning the bolt with a wrench, ensure the rotation of the knives around the circle.

It is more difficult if the washing is ceramic. For cutting hole in this case, a diamond crown will need. But even its presence in the home arsenal does not guarantee success - such a wash can easily be damaged if there is no experience of such work.

The Council is, and in another case it is better to turn to professionals. Usually in good stores for the sale of plumbing will be prompted, where and how it can be done, and in some cases such a service may also be provided.

If the mixer will be installed on the worktop, the hole will be drilled in it. To do this, you can use an electric door with a crown - an annular saw Ø 28 or 32 mm. Doing the desired hole with such a tool in the panel of the wood composite of special labor will not be.

Installation of a new mixer

As repeatedly in the article mentioned, the models of the mixers may differ in the fastening to the surface of the washing or countertops.

The diagram presents a mixer that is attached to threaded studs. In the set of oh, the studs are included with the brass nuts themselves, the clamping bracket in the shape of a crescent with holes for the studs and a rubber or polymer gasket of the same configuration.

There are models of mixers, in which only one stud is used, but this design will not differ particularly stable (there is no shock around the axis), and it is better to acquire with two.

This design provides a reliable installation on surfaces with a thickness of up to 30 ÷ 35 mm, which is particularly important when mounting the mixer on the worktop.

Another option is the mixer at the bottom of the cylindrical threaded part and the nut, usually m 34.

Such models are more suitable for installation on a metal washing. It is important that the bottom in the hole area is not a complex embossed configuration - an absolutely flat section is necessary, otherwise dense adjacent and reliable fixation will not be achieved.

Installation of different types of mixers has its own characteristics.

A. Installing the mixer with fastening on naika

The elongated lower cylindrical part will not prevent twisting the flexible hoses, so the installation begins, actually, from the mounting of the mixer itself to the washing.

The CM ESTER kit necessarily includes a sealing rubber ring, and a special groove is provided on the lower end of the housing. The first step is to install the gasket into this groove.

The threaded cylindrical part is inserted into the hole of the washing. In this case, it is necessary to ensure that the rubber ring remains in place, not shifted.

Then, a wide rubber gasket is installed below, which should also be included in the delivery.

Placed sealing gasket ...

Screw a brass fixing nut. It has a peculiar "skirt" - an extension in the form of a washer that will ensure maximum clamp through the installed already rubber gasket.

... and then - the presser nut ...

The nut is delayed in such a way as to ensure the mixture of the mixer on the sink. At the same time, it is necessary to control the correct orientation of the spinning - it must be located so that the sector of turning to the left and right from the central position is equal, and the inclusion lever or valves stood smoothly relative to the washing. At the angular location of the mixer, the position of the via is diagonally is selected.

... which is tightened by the key, locking the position of the mixer on the sink

Adjust the position is easy - you can loosen the nut, align the mixer and re-fix.
Now you can go to the installation of hoses. To begin with, the hose with a short fitting is screwed and tightened by a key to 10.

No winding of the threaded part of the packs of palaulies or fUM tape, as a rule, It is not required - it costs one or two sealing rings to ensure reliable sealing. The fitting is screwed up until it stops with an average effort - to drag dangerously, as the rubber ring may be damaged. Usually there is enough effort of the hand, and only then no more than one turn of the key.

... and then, just like the elongated

The next step is similar to the second hose - with an elongated fitting.
If water is planned for a metal-plastic pipe, then the fitting with fittings is screwed into such a sequence - the one that has a bend, and then direct.
After the hoses (fitting) are screwed, the sink can be installed in place.

Find out how to choose from our new article.

B. Installation of the mixer with fastening on studes

The feature of the installation in this case is that the hoses are screwed to install the mixer into the opening of the table top or sink, otherwise it will not be possible to tighten from high quality.

Initially, brass nuts are removed from the studs, and the studs themselves are screwed into the corresponding holes on the lower end of the mixer. On the heels, slots are usually provided for a direct or curly screwdriver, but, as a rule, they are easily twisted manually, without much effort. The tightening is strong here is not needed - it is enough just to wrap them up to the depth of 8 ÷ 10 mm so that they stood stably, without a backlash.

You can immediately try on the stud figure gasket and pressure plate on the studs, but then these items should be removed - they will be installed later.

Both hoses are in the hole of the washing (table top) fittings up.
It is necessarily controlled by the presence and correctness of the installation of the sealing ring on the mixer housing - the same as described above.
The next step is to screw the flexible hose fittings. The sequence of work does not change - first short, then elongated.
Mixer S. connected Hoses and screwed studs are inserted into the installation hole of the washing or table top.

On the bottom of the studs first, the curly gasket is dressed, and then the metal presser plate. Naked and manually, as far as possible, brass nuts are twisted.

After checking the correct location of the sealing rings on the housing and the direction of the gland, the nuts are tightened with the key to 10 (sometimes to 11) until it stops, so that the mixer is reliable fixation on the surface, without the slightest backlash.

Neatly installed mixer - bottom view

It is important to control so that there are no cracks left around the hull, not closed gasket - This sometimes happens with too much hole in the washing and improper centering of the mixer in it.

Everything, the mixer is installed, you can install the sink into place.

Repeat that all listed actions, of course, can be made under certain conditions and proper agility and without dismantling washing, but this is extra difficulty.

Find out what to choose, as well as consider the nuances, from our new article.

Video - installation of the mixer in the kitchen

Prices for components for mixers

Accessories for mixers

Connecting the mixer to the water supply

Making a washing is a separate topic that requires a detailed consideration in the article specifically reserved for it. It can only be noted that if it is mortise and mounted on an old place, then on the cleansed surface of the table top on the perimeter of the installation you need to strike the sealant. After pressing, he must reliably overlap the slot so as not to allow water to penetrate it.

If the car wash is overlaid and adjoins the wall, then after it is installed, the sealant also closes the gap between them.

Now it remains only to connect hoses to tap pipes. Hose nuts are usually already equipped with rubber gaskets, and no winding or excessive effort is required for reliable sealing of the compound. On the contrary, too strong tightening can lead to the destruction of the gasket and the appearance of leaks. It is enough to be tightened with your hand until you stop, and then only on ½ turns tighten 22 or 24 key.

With metal-plastic eyeliner, of course, it will be somewasher - It is necessary to thoroughly measure the desired segment, set it the necessary bending, and then tighten into the corresponding compression fittings.

Video: Connecting the mixer on the rigid liner

Usually, when connected by hoses or reducing pipes, the schemes adhere to: on the left - hot water, on the right - cold.

If the washer was shot, then do not forget to connect it back to sewage, setting the siphon and inserting the corrugated hose with a sealing cuff into the intended sealing pipe.

In fact, everything, you can turn on the water supply and try the mixer in operation. There is, however, another subtlety - it is recommended to start shed water with a tip-shot - aerator. The fact is that in the pipes, hoses, or even in the mixer can be accumulated small inclusions, which are able to quickly score the holes of this nozzle. After several liters of water alone, the aerator is easy to install on a regular place.

At the first start, all connections are checked for leaking. If there are signs of leakage, it is necessary to immediately eliminate these shortcomings with a small suspender.

The article covered the most common Methods for installing kitchen mixers. However, you can encounter with more complex options.

For example, if the mixer is picked up a shower head on a retractable hose, you will have to spend another switching and adjustment.

The bottom will be located (on the scheme - pos.1) in the corrugated braid or without it, a length of about 1.5 m, with a fitting at the end. This fitting, after installing the mixer to the regular place, is screwed into the housing intended for it. On the flexible hose itself, Georgic is installed (pos.2) - it will return to the place and hold it in this position, and at the same time will serve as a limiter length of the hose pulling. The position of this ship can be changed using a locking screw.

Another option is when two channels are provided in the mixer in the extension - for conventional tap and for purified drinking water. On such models there is an additional fitting (pos. 3) to connect another hose, which is from the system installed under the sink and purification.

The inclusion of the mixer for a set of drinking water is carried out by a separate crane or lever (pos. 4).

There are also more "sophisticated" schemes - with the thermostats that are dismissed under the sink, autonomous boilers, electronic control units, with a mechanical burden associated with the plug hole of the sink bowl, and others. Installation technology in this case should be detailed in the proposed product passport. However, if there were ambiguities in this matter, you should not do ammunition - it is better to invite a specialist.

Everyone once faces the need to replace the mixer in the bathroom, which is not subject to repair or is not suitable for the updated bathware. To figure out how to change the mixer in the bathroom, it is not necessary to be a professional plumber. The problem occurred can be solved by independently, having studied the technology of work and armed with the necessary tool.

The entire replacement process consists of two stages: dismantling the old and editing of the new one. Before dismantling the old device, it is necessary to determine with the new model.

What to pay attention to when choosing a mixer:

Fastening place. The bathroom faucets are divided into two types - mounted on the wall and embedded in the board of the bath or wall.

Zenta brand mortise model, built-in bath

Design type. Modern mixers from a constructive point of view are divided into ball and valve.

The balls regulate the supply of hot and cold water with one handle. They are more practical, more convenient, elegant. To prevent the ball mechanism clogging with small particles, it is recommended to install a filter for water purification.

With valves, all long ago familiar. They are adapted to long-term operation in the conditions of rigid chlorinated water.

Bathroom mixer

Prerefficers of repair or replacement of the mixer

The most common are the following breakdowns:

The closed crane flows.
Buzz when the water is turned on.
Little pressure than in other cranes.

It happens that the repair of the failed mechanism costs it is not suiced or simply inappropriate to implement it. The optimal solution will in this case be the replacement of the mixer. Change the mixer in the bathroom is more complicated than in the kitchen. In addition to the usual elements of switching hot and cold water, it has a bath / shower water supply system and a shower nozzle.

How to replace the wall mixer Step-by-step instructions

Relap hot and cold water on indigenous cranes. Then you should prepare the tools. You will need an adjustable key, screwdriver, pliers, hammer, chisel, flax and lubrication. A bucket and a rag can be useful, especially if the water pipes are already old and even with the valves closed, water remains.

Control key to replace the crane

Unscrew the nuts of the mixer using the adjustable key.

Unscrew the tap wrench

View the state of the eccentric. If they are pushing, they need to be replaced with new ones. As a rule, high-quality brass eccentrics do not require replacement.

Flashing arrow is wound on each thread, the plumbing paste is lubricated and screwed into the pipe. If there is no flax, a special sealing tape is suitable.

We wear flashes on the carving of eccentrics

Both eccentric are screwed into the same number of revolutions. Set them symmetrically.

The location of the eccentric depends on the distance between the tap nuts

Screw the bouts of the cups. Under the threads of decorative elements, the seal does not need to wink.

Screwd decorative chashes

Screw the nuts of the mixer manually until you stop. Do the key to twist a quarter turnover. If you take, you can damage rubber gaskets or fragile details of the new mixer.

Press the crane manually, do nuts cheese

Turn on the water, check. If leakage occurs, you should try to pick nuts. If it did not help, you will have to remake the work again. Perhaps not enough wretched seal or installed too thin gasket. After troubleshooting, the remaining elements - hussak and shower hose are screwed. Checked Switching water flow with bathroom to shower.

Ready! You can admire the result of its work

In principle, replacing the old mixer - the process is not particularly laborious. If you wish, you can cope with your task yourself. But there are moments when it is better to trust the specialist, whose experience will help to cope with unforeseen situations. Professional will easily unsubscribe rusty eccentrics, removes their remnants if they cracked and remain in the opening. Without attention, the many nuances will not be left, which involves the installation technology. In any case, to do or cause a worker - the decision takes the owner.