Self-ending house Block House. House covering Block House: Types of material, how to choose wood, options and features of installation Insulated block House

Blockhaus is a special kind of facing, imitating:

diagnosed log;
building timber;
decorative lining.

Due to its aesthetics and simplicity of attachment, the block mobile can be used not only for the external cladding of the house, but also inside buildings. A similar solution looks quite natural if the same material is used. This allows you to withstand a single style of design (including for wooden log cabins from a typical bar).

Is it necessary to fabulous "under the tree" of the walls of the wood? The answer to this can be the following nuances:

When assembling a log of logs or bar (using the principle of the connection "in the paw"), its external and internal surfaces in the presence of cladding in any case will look more stricter and more elegant than without it.
This allows the structure of the traditionally "Russian" view.
And finally, additional insulation of the walls of the building and their protection against external climatic influences is ensured.

You can separate the house by block mobile, however, some features of this design should be taken into account. When purchasing a trim cover, first of all, make sure that the samples you choose have special connecting grooves. The fact is that there is a type of blockhaus, the plates of which are deprived of such grooves, which markedly complicates their installation. As for the working conditions, it must be remembered here that it will be possible to enjoy the coating only after the final shrinkage of the structure.

Preparatory stage

For fixing the boards, a doom is prepared, which is mounted directly on the walls. The carrier design is made of 30 × 30 mm bars, placed vertically in about 60 cm. Before installing the frame produced using ordinary nails, the bars are processed by a composition protecting wood from fungus and preventing it.

At the stage of arrangement of the crate, it will be necessary to determine whether the insulation will be laid, which is usually placed between the block key and the walls. After completing this work, you will not only warp your housing, but also provide its good sound insulation.

Upon completion of the frame assembly, you can go to the direct installation of decorative panels. Regardless of the selected type of fastening, the operation is performed from the bottom up. We should not forget that the block cham must be treated in advance with an antiseptic.

Connection methods

Consider how to correct the boards on the crate. Famous mounting methods suggest the following options:

application of a retainer called "Klimmer", which in one of its part is inserted into the groove, and the other is fixed on the frame bars using selflessness;
fixation of blockhaus through screws or self-tapping screws;
nail feeding at an angle of 45 degrees in the groove.

The murmerous fastening ensures the propulsion of the connecting lock, due to which the necessary strength and reliability of the decorative coating assembly is achieved. The undisputed advantage of this method of fixation is the husty of the fasteners themselves and the ability to do without self-tapping screws that violate the integrity of the facing material and increase the likelihood of its splitting.

The second option to fasten the panels looks somewhat more complicated and needs additional preparation, manufactured as we are wearing a blockhaus building. To implement it, a round recess on half of its thickness with a diameter, equal to the size of the fastening screw, is made. In this case, the screw is completely interpreted in the hole, and from above is closed in advance by a prepared plug, which is subsequently stitched with a flush with the surface. A good alternative to a wooden tube is a special paste of appropriate (woody) colors, reliably protecting the hat of self-press from moisture and rust.

Video: Instructions for facing a private house

Since ancient times, at home in Russia was erected from a tree. A tree is an amazing material that creates the atmosphere of comfort and comfort. Today, the construction and finishing materials market offers wooden panels block house. The cover of the house by a block house give the building a presentable view and spectacular design. Block House allows at a low level cost to ensure high-quality protection of your home.

Advantages of Panel Block House

Panel Block House have a semicircular outdoor side, which in appearance resembles a rounded log. On the back there is two grooves, allowing to remove the tension and provide ventilation. Most often, these panels are made of ate, larch or pine.

Coniferous woods are distinguished by high durability.

The panels are widely used both for the external finish of the facade and for the interior decoration of the premises.

When evaluating the facade, the block of house should be noted the following advantages:

Favorable visual perception that causes a natural wood finish.
The mechanical strength of the material allows it to adequately resist external influences: small stones, sand, random strikes.
In case of damage, the material is easily restored by grinding.
Installation of the lining of the house by a block house is simple, it can be performed without having special skills in a short time.
Panels provide additional insulation at home.

How to choose a block house?

The panels may differ in their appearance and specifications. It is very important to choose the right width of the board. For outdoor sheat, it should be at least 150mm. Boards should choose the same.

The facade will look attractive for a long time if we use coniferous wood, as they differ in high resistance to rotting. Larch and pine due to the increased resin content in the wood have water-repellent properties. In these rocks contain natural antiseptic components, which ensures the protection of the tree from mold and rotting. The most durable and durable sheathing from larch panels. A block house from pine has the most affordable price. For external cladding, it is not recommended to use a block house from ate, since this material does not have sufficient strength. It can only be used for interior decoration.
Leafer of wood, for example, alder, oak, birches are used less often for the facade finish. They cost quite expensive, but individually can be ordered and such material.
Wood from the northern regions has greater density and durability. Externally, this can be determined by the distance between the rings - they are less.

Facade Tube Technology Block House

After purchasing panels, they should withstand some time on the street without packing for "acclimatization".

"Acclimatization" is necessary for the fact that in the future to avoid its shrinkage.

For installation you will need:

block house,
board Corner and Taming,
bar for doom
shkant (heater),
level,
antiseptic and brush,
wooden hacksaw
paper emery
drill,
a hammer,
sculpture and self-tapping screws.

The facial and inner surface, as well as spikes and grooves, must be treated with an antiseptic. After you apply the first layer, the surfaces and irregularities will appear on the surface to be treated with emery paper.
After that, you should apply the second layer of the antiseptic. Currently, there are a number of antiseptics in the construction market that can protect the surface from the effects of sun rays with different shades and color. Using them, in the future you can not paint the panel and not to cover with varnish.
A pre-purified smooth wall is set to a level with a level. Pre-concrete and brick walls need to be covered with a special waterproofing layer. Wind and moisture protection film should be attached to the metal brackets with metal brackets using a stapler.
As a dohable, you can use a wooden ram 30x30 mm. Attach it to the wall vertically with the help of screwdriver and screws. Between the bars you need to withstand a distance of up to 60 cm.
Warm building. Insulation sheets can be installed between the shelter bar. They are attached with special nails dowels. From above layer of insulation, cover the layer of waterproofing, securing it with the help of two-stroke tape.

For mounting panels, various fasteners are applied:

brackets;
nails;
self-tapping screw;
clammers.

It is best to use selflessness for this purpose - this will allow minimizing the possibility of the deformation of the skin when the moisture and temperature drops.

Benefit begin to install the refrigerated board on the self-tapping screw. Installation of panels Block House start from the bottom row. Wood panels are located strictly horizontally spike.
To the sump board tightly customize the panels and fix with the help of self-tapping screws. Drill a hole to a depth of 15 mm. The hole should be done so that it coincides with the diameter of the brazen (wooden tube from the same board). It is better to use the heater from solid wood, its size may be different. Universal diameter 25 mm.
Then screw the self-tapping screw, and the hole is closed with impudent. Its cut off and paint on the tone of the tree or a little darker. Before installing the bracket, it must be covered with a layer of PVA.
In the future, the Block House panel is installed using the fastening of the groove / spike and are fixed using self-samples. It is very important when installing the panels are spinning upwards, which eliminates the ingress of dust into the groove and accumulation of moisture, and therefore their long-term preservation. Between thermal insulation and outer panels, it is necessary to withstand the air gap.

Important nuances

In order to dock the boards on the corners, they can be confused at an angle of 45 degrees. Or use the corner board.
If the length of the wall exceeds the length of the panels, they are joined using the bar, the thickness of the equal thickness of the panel. In this case, the facade is well protected from the wind and looks more aesthetic.
In the case of small gaps when docking, they are closed with a jute rope.

Features of outdoor care

In order for the wooden panels to serve a long time you need to take measures to protect against external influences.

To eliminate the appearance of a white strip when the thorus tree is trimmed before assembly, covered with the same solution (varnish or versa), which will be covered in the future facade. You can get acquainted with the material about.

With the help of the simulatory, you can select the texture of the tree or give the desired shade.

First, the surface is primed, and then the panels are covered with colorless paint or varnish.

After drying the coating, the surface is defined.

After grinding, the final layer of paint or varnish is applied to the surface. To panels for a long time look beautiful for the coating, you need to choose high-quality materials with a long service life. But still periodically, in seven or eight years, it will have to renew the coverage. It is advisable to apply the same tone, the same paint or varnish, and otherwise before applying the new coating will have to completely remove the old one.

Installation of block house (video)

Conduction options by block house

Today, the facade of the facade of the house can be performed not only by wooden panels of block house, but also plastic (vinyl) and metal. In each of these options, the facade is obtained, which is almost impossible to distinguish from a natural log cabin.

Metal panels Block House "under the log" are inexpensive material, resistant to corrosion, as they are made of galvanized steel with a special coating. Panels have a rounded shape, externally resembling a rounded timber.

Vinyl block House also has a number of advantages. It:

Easy to care.
Durable.
Frost.
Not inclined to corrosion.
It has a presentable appearance.
Vinyl siding not only definitely imitates the color of wood, but also its texture.

How much your house would be new and from what material would not be built, it still needs good protection. Also, it is necessary to close insulating materials that do not tolerate open interaction with the external environment and moisture. That is why it is important to choose one of a variety of diverse finishing materials, which is optimally suitable for all items. Despite the fact that the market offers a tile, stone finish, the latest synthetic materials, etc., the finish of the house block to house outside still remains in fashion.

Block House photo of houses

Earlier, we have already loosened how to repair a village house, in the same article we will talk about how to see the house Block House, as well as how the home finish is done by the House Block to House.

Preliminary preparation

As in any other form of construction works, preparatory work is required before the trim. By the way, it is worth noting that the best time to cover the house by a block house - at least a year after its construction. So, to begin with, it is necessary to make sure whether all the work on the insulation of the house has been produced. In case of plating a wooden house outside the block to House, it is necessary to cross the junctions between the logs. Otherwise, after the trim, you will not be able to warm the house correctly, and it will remain cold.

The next step will be the choice of materials needed to cover the house by a block house. Such a lining consists of a variety of layers, including:

parosolation film
okeekhet
heat insulation
controlling
windproof film

It should be noted here that using the Block House for finishing the house outside of wooden and brick houses a vapor barrier film will be superfluous, so it can not be used.

As for the thermal insulation material itself, then it is necessary to be based on the materials of the house, the thickness and density of the walls. For example, 15 centimeter walls require 10 centimeters insulation. But at the same time, if the cover of the house is produced by the house of the house, then a sufficient layer of insulation with a thickness of about 5 centimeters is sufficient.

The bar for the crate is selected exactly the same thickness as thermal insulation, since their thickness should accurately comply with the calculated dimensions to achieve the best effect. The inches inserted insulation is covered with a film protecting against wind and then covered with a counterclaim.

This design provides a high level of thermal insulation, as well as impeccable ventilation of a natural type, due to which the house will be dry and warm.

Choise

The choice of block house, in fact, only the sizes and the material from which the board is made. Usually used general division of boards for block house in two categories:

wide board (width over 15 centimeters)
narrow board (width of less than 15 centimeters)

A narrow board is usually applied in rooms, and wide - outdoors, as wide boards provide better wind protection. However, due to this, the price of a wide board is slightly higher.

In terms of material, boards from larch, which possesses wonderful properties, is considered the best boards for block house.

high strength
not exposed to moisture
not susceptible to rot
has a long service life

In addition to larch, you can use pine, it has more modest characteristics, but will provide excellent opportunities for use in the quality of block house.

Regarding the length of the board, you can give the same advice as in terms of width - long boards is better, as the fewer joints, the better the protection will be.

Of the above, the tips can be concluded that it is better to use more expensive and reliable materials that will serve much longer.

House cladding Block House

Of course, the above subtleties are many and this is only a small share related to the choice of block house. Now we will talk about what stages are waiting for you when repairing the facade of a private house, as well as possible difficulties when working with it.

The first trick that will help to avoid the accumulation of dust in the joints of the Haus block - place the groove boards down and spike up. Since dust will not accumulate in the groove, the block house will last longer and will not lose his kind. In addition, it is necessary to make a small gap between a block house and a ceiling and a block house and a floor. Such a technique will help create natural ventilation of the inner cover, which will also extend its service life.
For fastening the trim, it is worth choosing powerful fasteners that are not subject to corrosion. For example, galvanized or anodized selflessness will fit in the best way. They will perfectly hold a block house, and will not spoil the kind of rust.

Nuances Protection Block Haws

So, the covering block house of your home is completed. Now there is a question of processing boards so that they do not lose their type and properties, and could serve you for many years. From atmospheric influences, lacquer coatings are well protected, you can also use special paint types. When painting it is necessary to take into account that as far as wood would not be, it still gives moisture, which is why cracks and white stripes in places of connecting boards appear during shrinkage. To prevent this, it is enough to simply clear the spike and the groove of each board before assembling the skin with the same paint coating that you will paint the remaining surface of the block house.

In addition, it is necessary to carefully follow the instructions of the manufacturer of the paintwork, correctly progress the surfaces before painting, observe the temperature regime.
As you can see, the cover of the house by a block house not only makes your home more beautiful, but also perfectly protects the internal components of isolation from external influences. Knowing simple rules, you can easily get a good result of finishing work and will enjoy the view of your home for many years.

House clamping block House video

Many dream of a wooden house, because this is a standard of ecological purity and beauty. But the construction is completely from the tree will cost the customer in a round sum that not everyone can afford. The lining of the walls of the house by a block house is one of the options for saving the means and obtaining the desired effect.

How to strip the house block house - alternative to dear cut

A modern block house is one of the types of car board, which has an outer side of the panel in the form of a rounded log. This casing material is used to finish the building, both from the external and inner side. The main advantage of the walls of the walls by a block house is an excellent appearance and ease of fastening. Each panel has a "groove-spike" compound system, which allows without special tools and in the absence of professional skills to perform installation independently.

The arrangement of the internal, as well as the external decoration using the imitation of the log is a practical and modern step. Now in the construction market you will find, as well as plastic and metallic. Wooden has several quality classes, for example, a class of extra and class, but are best suited for interior decoration, since they have a minimum amount of bitch and the absence of any other defects of wood. A wooden low-class bed house is great for exterior decoration.

Plastic products can be both painted in mass and have several layers of paint from the front side. It is better to choose painted in the mass, as well as products produced from primary raw materials. Siding, produced from waste, has a significantly smaller service life.

Advantages and disadvantages of materials - choose carefully

These procedures must be performed at least once every five years, although for a longer service life of the finishing material, it will not be superfluous and impregnated once every two years. In addition, a wooden block house refers to the most expensive kinds of similar siding.

Metal and plastic types compared to wooden also have a significant minus - how not to twist, but they only imitate the appearance of the wood texture.

From afar, the difference will be difficult to determine, but near this visual deception is revealed. All species combines one undoubted quality - during the lining of the house by a block house there is an opportunity to further insulate the house. Not to mention the aesthetic perception of the trimmed house - even the most expensive structure from the slagoblock will acquire the appearance of a rustic hut, with the attractiveness peculiar to such buildings.

Covering House Block House with her own hands - Features of choice

Despite the external simplicity, choose a suitable wooden block house for the outer finish of the facade of the house seems not the most common task. First, you should focus on the width of the block house. The fact is that each manufacturer has its measurements, and the material bought in two different places may differ in the parameters of thickness and width.

So try to choose the most common sizes. For example, the exterior buildings are best used wide boards, up to 150 mm width. Secondly, it is necessary to determine the type of wood from which the board is made. For outdoor siding, block houses need to use boards of coniferous trees (spruce, pine, larch) - they have increased resistance to the rotation process.

Also, it is also necessary to find out from what area of \u200b\u200bthe country this board was on sale. Wood from the north has greater density, which means it is more durable. This can be identified even visually - the northern wood between the annual rings has a smaller distance. Naturally, for the finishing of the facade of the building, a block house can use a board not only from northern forests.

TECHNOLOGY OF HOUSE BLOCK HOUSE - Step-by-step instructions

In addition to the Block House itself, you will need other finishing materials - sin not to use this opportunity and not inspired by the building at the same time. That the trimming of the stone is that the covering of a wooden house by a block House does not have a fundamental difference. To start the wall, it is necessary to surround the layer of vaporizolation so that the moisture from the house does not penetrate the outward, forming condensate, which will significantly reduce the thermal insulation properties of materials.

Parosolation membrane is on sale in every construction store. It is fastened with a mustache, while connecting the stripes by 10-15 cm. The joints of the joints are best sealed with aluminum scotch. Then you can proceed directly to the construction of the building.

How to strip the house block house - step-by-step scheme

Step 1: Dooming under the block house

From the thickness of the plates of thermal insulation directly depends the size of the bars that are selected. For example, for central regions, the maximum thickness varies in the range of 10 cm. The distance between wooden bars should be no more than 60 cm, although it is best to adjust it under the size of the insulation plates. Before the attachment, the selected bars must be necessarily processed by an antiseptic. For installation it is better to use screws or special nails (if a wall of stone is a dowel), with wide hats.

When building a house, building materials of different origin are used. In many countries, natural products prefer to use natural items. They have been used since ancient times for construction, decoration of buildings, bringing positive energy, creating a comfortable environment for living.

Features of a wooden block house

Among the modern natural materials used to the outer decoration of buildings, you can still meet a block house - a variety of wooden lining.

A beautiful and stylish house, covered by a block house, in the photo is indistinguishable from a high-quality natural cut. In addition to external similarities, such a decoration of buildings has a large number of common positive parties.

Houses built from a natural log are famous for their longevity. Nowadays, it is often possible to meet buildings, more than a century building, which have not lost their qualities and are actively used. In such houses it is easy to breathe, there is no increased humidity, a favorable psychological climate is formed.

To replace the popular material, the industry has established a production of inexpensive coatings. These include a metal profiled sheet and siding (see), imitating a natural block house. Each of these species has a beautiful appearance, good strength indicators, quite a long time of use, but are not suitable for internal use.

Vinyl or acrylic siding becomes especially popular for creating a stylish building. Solving what kind of sample is better, siding or block house, it should be remembered that natural materials are more suitable for the arrangement of people's accommodation facilities due to their environmental purity and harmlessness.

At the same time, it is determined, the better to strip your home, many make a choice towards siding, guided by the available prices and long use, the lack of the need for complex care and additional measures to maintain the relevant appearance. However, this concerns only high-quality samples from reliable manufacturers.

Positive characteristics

The house covered by a block house of wood combines many advantages allocating it among other materials:

one). High environmental characteristics.

2). The absence of harmful discharges allow it to be applied to finishing not only outside, but also inside buildings, during the construction of mansions, cottages, summer buildings, saunas, baths, economic premises.

3). Good hygroscopicity and vapor permeability of wood contributes to the absorption of excess moisture in the room, and the excavation of their outward, leading to a decrease in the level of humidity.

four). Due to the good noise absorption and low thermal conductivity, the block house is an additional insulation and soundproofing layer.

five). Simplicity of installation (see), which does not require special equipment and tools, makes the bedding at home by a block house with a fairly simple operation that allows the neat owner to make the beautiful decoration of its own residential and household structures.

6). Beautiful appearance allows you to implement modern design projects at a high level of quality, for example, in a popular rustic style, build beautiful, reliable, durable houses.

Variety of material

The appearance of the block house can be compared with a wooden clapboard having a convex facial part, carefully trimmed under a rounded log. There is a variety with a cut convex part. Such a block house has a surface resembling a timber.

The strength, reliability and durability of the surface is ensured by the compound of the groove-comb (spike, spool). To do this, on each product, on the one hand, the groove is torn, and on the other, there is a spool. Such a type of docking of the Blocheus bands with each other creates a high-quality connection and protection against moisture penetration, cold.

For the manufacture of block house used in the outer decoration, coniferous breeds are most often used:

Pine.
Larch.

A block house of ate has insufficient strength quality for outdoor use, but it can be successfully used to finish the interior.

Olhi's hardwood, oak, birch, it turns out a durable, beautiful and eco-friendly material. The dimensions of its use are limited to a fairly high price. Such types of block house can be used for stylish interior trim cottages, baths, saunas.

The premises decorated with wooden block house are very beautiful, have a pleasant golden color, a warm surface. In such a room, a comfortable environment is created for a person who does not harm health, but on the contrary, having healing properties due to the natural components. The tree can take fatigue, replenish the strength, restore the mental balance.

The house, carved with a block house, not only looks beautiful and stylish. With this finish, you can get a durable wall covering, reliably protecting on atmospheric influences, creating a comfortable and warm living room.