How to make a wooden frame with your own hands: a step-by-step description and recommendations. How to make a frame for a picture with your own hands? Frames for pictures - a photo How to make a wedding from a wooden frame

All photos from the article

If you have a lot of photos or any paintings and other compositions that you would like to hang on the wall, then you cannot do without frames, any of the above options will look much better with them. The cost of ready-made options is quite high, but if you wish, you can make frames on your own, this is what this article will be devoted to.

What you need to work

Let's figure out what materials and devices will be needed when carrying out work:

Wooden elements	These can be a wide variety of options: from slats and remnants of a plinth or platband to any other similar materials. If you want to create a very skillful piece, you can purchase ready-made wooden moldings and use them.
Saw and miter box	With this simple kit, you can file joints ideally at an angle of 45 degrees, thanks to which the joints will be of the highest quality, which has a very positive effect not only on the reliability of the products, but also on their appearance.
Carnations and glue	Joints can be made in two ways: either using finishing nails and reduced caps, or using wood glue, which can also provide good reliability. If you need very high strength, then the options can be used together
Special clamp	If you are going to make frames more than once or ideal quality is important to you, we recommend purchasing this type of equipment, since with its help you can press the parts very well when gluing, while maintaining the ideal geometry of the structure

Important! And do not forget about paints and varnishes, a wide variety of options can be used - from varnishes and impregnations to stains, and special compounds to give products an antique look with gilding and patina.

The working process

Even someone who has never been involved in such an activity can figure out how to make a wooden frame with his own hands. We will look at the sequence of work to further simplify your work.

Preparation of everything you need and cutting blanks

First of all, you need to choose photos, paintings, collages, embroidery and other compositions that you want to arrange within the frames, this is necessary in order to take the actual dimensions and make exactly the configuration that you need, and not adjust the elements to the finished version , this is a huge advantage of homemade frames.

As for the process, it happens as follows:

• If there are passepartout (cardboard frames) in the photo, then they need to be made in advance and the dimensions of the frames should be taken using them, with the exact parameters you can proceed to the choice of material for production, both and other options are suitable, you can find many blanks on sale, the price which is not high, they are perfect in our case;

• Next, you need to make measurements, it is important to do this carefully so as not to be mistaken, otherwise the finished product will come out crooked. Make sure that paired elements are the same size;
• Cutting workpieces at an exact angle used to be considered a difficult and painstaking job, but nowadays you can buy a miter box with a saw for little money and cut wooden elements very accurately and very quickly. The most important thing here is to use a saw with a fine tooth, so that it provides the best cutting quality, the more ideal the edges, the better the elements will connect and the more attractive the finished product will be;

• Last of all, on the back side of the blanks, you need to choose a groove for the glass, its depth should be 3-4 mm more than the thickness of the glass, so that it can be fixed with small studs.

Assembling the product

The instructions for carrying out this stage are very simple and straightforward:

• First, it is necessary to connect the two elements and securely fix them, as noted above, the best fixation method is to use a special corner clamp, with its help you will securely fix the parts in the desired position, and they will not move when dry, the geometry of the connection will be ideal;

• After gluing, you can proceed to further work, first of all, this is the decor of the wooden frame, here your imagination is not limited by anything, so the style of the design and the chosen color scheme depend only on you;

Important! You can achieve the effect of antiquity by painting the frame first with dark paint, and then with light paint, after which the top layer is wiped with fine sandpaper in some places.

• Then you need to insert the glass, behind it there is a mat if it is available or immediately a photo, then you need to put in thick cardboard for rigidity and fix this whole system with nails or attach special rotary clamps of a small size;

• For wall mounting, you can attach special lugs from the back (they can be purchased at furniture hardware stores) or drill a hole in the diameter of the fastener to simply put the frame on the head of a protruding nail or self-tapping screw.

Output

Making frames is a simple process, while you can get a unique result, because you can implement any ideas, the main thing is to choose the appropriate materials. The video in this article will tell you additional information on the topic, if you have any questions or important comments, leave them in the comments below.

Cool trendy photo frames are an essential element of any interior. DIY photo frames can become not only a unique accessory for your home, but also serve as an excellent gift for family and friends.

In this post, the site has made a selection of 14 cool ideas on how to make a photo frame with your own hands from simple materials, many of which can be found even at hand.

1. Frame made of dry twigs

This option is suitable for creativity with children, they will willingly help you first collect sticks in the forest, and then they will happily break them into short pieces.
What you need: wide brim frame, glue gun, sticks

2. Frame from an old rustic window frame

3. Photo frame from an old book

An extraordinary frame from an old book is a great example of a photo frame from the materials at hand. Suitable for a small, but very sweet to heart photography.

4. Frames made of cardboard tubes and rolls from toilet paper

Such a creative panel is suitable for some photo story, for example, about your last trip.
What you need: toilet paper rolls and any other cardboard tubes of different diameters, scissors, glue, paper knife, pencil.
Step by step instructions in the pictures below:

5. Large panel with a metal mesh

What you need:

How to do:
Attach the metal mesh with a stapler to the frame from the back side. Attach photos to the grid with clothespins.

6. Dry moss frame

A stunningly live photo frame made of real moss is a sophisticated decoration of your home.
What you need: an old wooden photo frame, dry moss (can be ordered), glue.
How to do it: Just glue the moss around the perimeter. Decorating will take no more than 30 minutes and will bring a lot of fun 🙂 This photo frame is perfect for a wedding gift.

7. Photo frame from old magazines

For this frame, for sure everything is at hand. Everything you need: old magazines, the frame you want to decorate, glue (it is convenient to use a glue gun).

Step by step instructions in the pictures below:

8. Photo frame made of thick sticks

9. Photo frames from ice cream sticks

These simple and cute frames are perfect for family and children's photos. In this example, ice cream sticks are supposed to be decorated with multi-colored scotch tapes, but we propose to paint them by hand.


And here is an even simpler version of the frame using sticks.

10. Brutal cement photo frame

What you need: cement, container for mixing cement, cardboard or cereal / cereal box, etc., frame fasteners, glue, paper knife, tape, small pieces of wood (you can cut a branch).
Detailed step-by-step instructions in pictures can be found below:

Hello, hello friends! Are you ready to plunge into the world of wood? Today we will try to make a photo frame out of wood.

Master class evaluation 4 out of 5 based on 9874 votes.

Method 1:
Photo frames are here for reasonable prices. Discounts on goods in 719 online stores are a return of part of your money. Organizers and tool bags are here to help craftsmen. How convenient to make a frame for photos.

Method 2:
A real way to make money on the Internet, register here for free and earn. Discounts on goods up to 60% do not miss the moment here Joiner how to make a frame for a picture from wood with your own hands in a garage workshop.

Method 3:
Today the package "Words and letters from wood" arrived. We have ordered a name for our son, which indicates: date of birth, height, time of birth, weight and a separate photo frame for your baby's photo! We bought this decoration for $ 27, and the package arrived from Minsk to Brest in three days.
If you liked it, please like it and subscribe to the channel. If you have a desire to order such a decoration, leave a comment on this video!

Method 4:
"VseInstrumenty.ru" offer the option of making a photo frame with your own hands at home. The review uses both hand tools and electrical ones. Now it's easy to make such a frame for photos!
We wish you every success!

Method 5:
This video shows the process of making a picture frame.

Questions asked daily

• What tools are needed for woodworking?
• Advise master classes or woodcarving circles in Vladivostok, I want to take my child away from the TV / computer and do something useful;
• I can't watch the next video tutorial, an error pops up. What to do?
• I want to order a wooden photo frame in 4 way in the amount of 47 pieces, who should I pay for the work? Must be delivered to Kiev

More video

There is always the question of how best to glue a wooden picture frame. Frames with a curly profile are joined in a "mustache", ie. the ends of the parts are filed at an angle of 45 *. Clips for tightening the frame when gluing have been around for a long time, but here's a strange thing, they continue to be invented to this day.

Moreover, such clamps are designed by the craftsmen themselves, especially those who have to make a lot of such frames for work. Apparently one single universal clamp has not yet been invented.

I don't make picture frames every day, and I usually use two methods. The first option is to tighten the parts using a special corner clamp, photo above. But this method has some inconveniences, the corner clamps that I use do not allow me to collect small frames.

There are other fairly simple gluing methods. To make such a device is a matter of just a few minutes. For work, you need a flat square platform made of chipboard or thick plywood. Support bars are screwed on two edges with self-tapping screws. Please note when assembling, the bars should be at an angle of 90 * relative to each other. Use a metal square for an accurate fit.

Next, we smear the already prepared and angled parts of the frame with glue and tighten with two long clamps. When squeezing, be sure to check all corners of the frame with a square. The photo shows how else you can check the correctness of the assembly. Graph paper is laid on the device's platform, and during assembly, you can see how the parts have risen relative to each other. And also, so that you can use your device for a long time, place the paper at the corners so that the glue does not stick to the site.

Another option looks more like a professional angle clamp, although in fact it is also homemade. Four separate flanged stop corners are used here. All four corners are pulled together from the inside with elastic rubber, tension rope or cable. In the classic version, all four corners are tightened with one bolt, and the stop corners are installed on four diagonal rails.

As for this particular product, the whole problem here is to make these same corners with bumpers. In my opinion, the methods listed in this article are quite suitable for making a small number of frames. There is also a method, an article. Although I repeat, the craftsmen continue to invent corner clamps for assembling frames, everyone is looking for the most convenient option for themselves.

Never fond of arts and crafts? It doesn't matter, because learning to do something simple with your own hands is not only useful, but also pleasant. Let's try to make a nice wooden photo frame. After all, you always want to surround yourself with bright memories of a vacation or smiles of loved ones.

How to make a frame for a photo with your own hands at home? It's very simple :) You will need quite a bit of it: a knife, an awl, a saw, a hammer, a small drill. Almost every family has all this. So you can start

Before that, however, it is worth visiting the forest. There you will find the roots of various shrubs and trees, branches, cones, acorns, from which you can then make real works of art.

If you are creative, then almost every root can make an original craft. Of course, it is impossible to give specific advice on what to make of this root. After all, in it each person will see an original object, on the manufacture of which he will work. Involve your children, thanks to children's imagination, you can make such extraordinary figures that everyone just gasps.

Now let's start making such a useful thing as a photo frame. It can also be a frame for interior decoration. You can make a completely new one or restore an old one using natural materials.

First, we clean it from dust and varnish. We grind. After that, we prepare branches and cones, tree bark. The frame is opened with glue, and a variety of materials are glued. We place some symmetrically, others asymmetrically. It all depends on your imagination and the imagination of the child.

It is better if the entire surface is covered. Then everything has to be varnished and your joint creation can be mounted on the wall. The photo shows one of the examples of the design of the old frame. This is not a standard, each master will make his own unique work.

When collecting natural material, teach your child to use roots and branches from trees that have been cut down. You cannot break growing trees, causing irreparable harm to your native nature.

Thus, several useful educational processes that will help your child become a worthy citizen of their homeland will be combined in a short joint production of handicrafts. He will receive the skills of working with the instrument, a lesson in respect for the surrounding nature.

How to make a photo frame

When you get good pictures, you want to print them and hang them on the wall. But as always, there is a problem with photo frames.
The ones that are on sale do not always match the size and color for the implementation of your idea. The only thing left is to make the frame for the photo yourself.

Moreover, it is very simple and you can get by with a minimum of tools. First you need to find wooden planks, from which we will make the frame.

I usually use small curly or rectangular glazing beads for this, which are sold in the construction markets. Next, you need to decide on the shape of the corners, as a rule, these are two options - at 45 degrees and 90.

The first option looks more beautiful on frames covered with a transparent coating or without it. I prefer the second option with painting in black. Then we saw off the four sides of the future frame, and adjust the corners, especially if we sawed off at 45 degrees. When the frame is roughly fitted, align the planks with fine sandpaper or a small planer.

There are several ways to fasten the planks together. The easiest way is to glue them together with a sufficiently strong glue. For this, you can use epoxy resin or transparent "Moment". A more reliable connection will be gluing and hammering staples from a large stapler. Such a connection will suffice in the vast majority of cases.
If you need to make a large photo frame, then you can make the corners of thick tin or aluminum, in this case you can attach them with small screws.

I make the smallest frames even easier - the strips themselves and the photograph are glued to the thick cardboard substrate, this is enough for the whole structure to hold firmly.

You can go beyond the usual materials for your frames.
I saw frames made from kebab skewers, cut out of 1 liter beer cans, just a contour smeared with glue and sprinkled with sand and shells.

Having shown imagination, you can even make a volumetric frame - in the form of, say, a window. To do this, you need to make a copy of a real window frame and insert a photo instead of a background, if you choose a photo successfully, you can achieve an amazing effect.

Wooden or what can be made from scraps of boards

In any carpentry workshop, be it home or large-scale production, there are always a lot of different scraps. Of course, it's not a pity to throw out defective ones, but those that are more or less suitable, I want to use it somehow. I have already touched on the topic of scraps on the pages of the site, these were curvilinear and radius details, and again decided to return to it. Very often in the search queries for which visitors come to the site, you can find the following: what can be made from scraps? So I want to suggest a topic on how to make a simple frame for a picture or portrait with your own hands. I must say right away that what I will tell and show in this article is of course not of artistic value. The goal is not to create a work of art, but to show how you can make a simple and necessary thing, durable and light, using "illiquid assets". And how to make a work of art, it will depend on your imagination, taste and artistic ability. And so to the point.

I made a frame for the finished canvas 450x550mm, so the dimensions were determined in advance. The frame requires four corresponding strips with a margin of approx. 150 mm. The first thing to do is to drive them into the same section size. This is important because the corners will be cut at an angle of 45 degrees and if the width is different, then the cut will also be cut accordingly. As a result, we get "not going out of hand" in the corners. You can, of course, connect the corners and not at 45, but at the butt-edge junction, this is as convenient as anyone. In this case, the width of the posts and jumpers may be different. With any available tool, we make the slats the same in thickness and width. Next, mark the dimensions of the future frame on the slats. When marking up, you need to make indents from the edges, since we will file the corners from the outside of the line. Since I had a canvas, I started from the internal dimensions of the frame, hence the markup. Once marked, the task is sawed off as accurately as possible. There are many ways, a good hacksaw and a miter box, a miter saw, a circular saw with a device for sawing corners, a band saw with the same device, and so on ... The main thing is the accuracy of the saw. In addition to a precisely maintained ula, you need to make a cut perpendicular to the base plane, so that when connecting parts there are no so-called "beeps". This is when one of the planes joins tightly, and a gap remains on the opposite side.
Sawed off, move on. Now, on the seamy side of the blanks, you need to select a quarter, in order to then insert a canvas or portrait and fix it with a glazing bead. The procedure is not mandatory, you can do without a quarter, but it seemed to me that this would be more reliable fixing the canvas. I used a horizontal slot cutter, but you can do the same with a hand router or circular saw, with the option to adjust the cutting depth. Almost all household circulars produced now are capable of performing such an operation. Determine the size of the quarter based on what will fit into the frame. It can be a photo under glass, for example, or a mirror. In any case, there must still be room for the fixation. Although if it is supposed to insert something without the possibility of replacement, you can not choose a quarter, but make a cut of the appropriate size, and insert a mirror during the assembly process. Then it will be in the frame "for life". In this way, window sashes were once made.

I cut out part of the workpiece in order to somehow select the corners, this is firstly, to increase the mating area at the corners, while making the frame visually less massive, this is secondly. Your imagination may go further than mine.

The next step is to ensure maximum bond strength in the corners. I had a small picture in a factory frame and shattered into five parts when it fell. It turns out the corners were fastened from the seamy side with brackets from the construction stapler, two per corner, that's it! Let's learn a lesson and not repeat the mistakes of others. We will make a connection of the corner on a plug-in tenon, this, together with good wood glue, will provide sufficient strength. Select a groove on the end cuts. What it will be depends on the thickness of your blanks. I just made the cuts with a regular circular saw blade. I got a kerf of 4 mm and a depth of 12 mm. The section of my blanks is 45x18 mm. A spike of this size will be sufficient. Having made the cuts, you need to make a thorn. I took a rail of a suitable width and passed it through a thickness gauge to obtain the desired thickness. This can be done with a regular jointer, and even an electric planer, but keep in mind that the spike should fit tightly and at the same time without excessive force. If you have a thickness gauge, but it does not allow you to plan such thin slats (often the minimum size is 5-6 mm.), Place the strip on a previously planed board and skip it in a bag. Thus, you can even plan veneer.
Carefully fit the cleat to the groove, ensuring maximum tightness in both thickness and width of the cleat. The fibers should be directed perpendicular to the end cut. Fitted, you can paste. If you intend to insert a mirror, then the inner edges of the frame must first be rolled with a mill (if you want to do this at all). I did it on the assembled one, so the inner corners were rounded. If the cutter passes the workpiece disassembled, the angle will naturally be right.

When all the corners have been collected, you can somehow process the edges. If you do not want to use a router for this, then at least just a little walk over them with sandpaper, so as not to blunt a lot. It is generally not recommended to leave sharp corners, especially on softwoods. After finishing, there may be unpleasant surprises in the form of small but clearly visible chips. I rolled the inner edges with a bevelling cutter, to the depth that a quarter allowed, and the outer edges with the same cutter, only with a larger diameter and milling depth.

For this, you can safely proceed to grinding, and then to finishing. What it will be, you know better. I limited myself to stain and semi-matt varnish (2x3 layers, both polyurethane materials). And finally, insert into the frame what you planned and fix it well. If you do not want to insert the glazing bead, you can simply cut small wedges out of tin and press them in, thereby fixing the object. This is appropriate if you are inserting something hard. In my case, it was also necessary to provide some tension on the material, the glazing bead allowed this to be done.

Processed