Repair Design Furniture

Log cabin of a bathhouse with planks and a chopped veranda. Sauna with decks - optimal use of a small area Log bath with decks

1. Log cabin 4 x 6, five-walled with an internal protёs of walls (cutting the corner "in the paw", size 4 x 6 is the internal dimension from wall to wall)
2. Net height from floor to ceiling 2m.30cm.
3. Floor logs and ceiling beams from hewn logs.
4. Rafter system for a gable roof with a ridge height of 2m.50cm. running their boards 50 x 150
5. The rafter beam protrudes from the walls of the log house by about 50 cm, and the roof slopes fall below the rafter beam by 15-20 cm, which allows you to get:
a). Pretty cute appearance.
b). Lowered roof slopes protect walls from rain
c). Near the wall it turns out approximately 70cm. a dry space where you can make a woodpile.
6. Lathing - unedged board 25mm.
7. The roof is covered with roofing material (roofing with any other material is discussed).
8. The pediments are sewn up with clapboard and a frame is made in them for the windows of the “second light”
9. The final floor in the bathhouse and on the wards is a grooved floor board 38mm.
10. Two bath doors from 50mm boards. and two double windows 60 x 60
11. The frame is assembled on moss and installed on posts 40 x 40 x 40, assembled from foundation blocks on a sand bed (sand is provided by the customer)
Any changes are possible according to your desire!!!
YOU CAN SEE YOUR LOGO BEFORE IT COMES TO YOU,
Write us an email and we will send you a photo of the finished log house in the size you need.

Facilities

Equipment: Under the roof
Foundation, walls, floor beams, roofing.

From our point of view, the most competent project for starting the development of the site is a bathhouse with floors, the size of the log house can be 6x4 and 6x6 and the one that the owner of his site wishes. You immediately get a comfortable house where you can live quite comfortably and without any haste start thinking about and building the main house. After the house is built and the bath (after finishing) begins to fulfill its main purpose, the space above the steam room and washing room will become a cozy sleeping place for guests.

Bath with tents
project
project
project

A bathhouse with planks looks the same as a bathhouse with an attic, only in this case the rafters are made of 50x150 boards. On such even rafters, it is easy to insulate the roof and sheathe it with clapboard. If you add a porch, then, if desired, a blanket can be made above the porch.

OPTION IN BAR 150x150 mm from 180,000 rubles

OPTION IN LOG f 24-26 from 266,000 rubles

Total 266,000 rubles. and on your site there will be a bath processed under a planer:

1. Log cabin 4x6, five-walled (cutting the corner "into the bowl", size 4x6 is the size along the axes)

2. Net height from floor to ceiling 2m.20cm.

3. Ceiling beams made of hewn logs (floor beams at the request of the customer).

4. Rafter system for a gable roof with a ridge height of 2m.50cm. their boards are 50x150

5. The rafter beam protrudes from the walls of the log house by about 50 cm, and the roof slopes fall below the rafter beam by 15-20 cm, which allows you to get:

a). Pretty cute appearance.

b). Lowered roof slopes protect walls from rain

c). Near the wall it turns out approximately 70cm. a dry space where you can make a woodpile.

6. Lathing - unedged board 25mm. (at the request of the customer, you can install edged)

7. The roof is covered with roofing material (roofing with any other material is discussed).

8. Gables chopped log (discussed - they are sewn up with clapboard and a frame is made in them for the windows of the “second light)”

9. Finishing floor in the bathhouse and on the wards - floor board 38mm.

10. Two bath doors from the board.

11. Log cabin is going to tow

12. Installed on posts 40x40x40, assembled from foundation blocks for sand bedding (sand is provided by the customer). Strip foundation by prior arrangement

Any changes are possible according to your desire!!!

Shipping is calculated separately.

Is it interesting for you?

Is it possible to leave the round timber inside the log house when cutting “in the paw”?

What is the best way to drain water?

Do you need a foundation for the stove?

What is the best way to cover a roof?

Get detailed advice on all issues.

Log cabins available
from 3x5 to 4x6
with delivery tomorrow

Bath with beds 4x6 from the Good Bath.

Log cabin with decks for 185,000 rubles.

As soon as you become a happy owner of a land plot, the question immediately arises - you need to start somewhere, something needs to be built for the first time.

From our point of view, the most optimal project for starting the development of the site is a 4x6 bathhouse with decks. You immediately get a comfortable house where you can live quite comfortably and without any haste start thinking about and building the main house. When the house is built and the bath (after finishing) begins to perform its main functions, the space above the steam room and washing room will become a cozy sleeping place for guests and a place for children to play.

A bathhouse with planks looks the same as a bathhouse with an attic, only in this case the rafters are made of 50x150 boards. On such even rafters, it is easy to insulate the roof and sheathe it with clapboard. In the right picture, you can see that the shelves protrude slightly into the room relative to the fifth wall. In this case, the ladder does not interfere with the approach to the stove.

You can see how you can equip a bath with floors

If you attach a veranda to the bath, you can get a second floor

You can see how you can equip a bath with two floors

Bath layout 4x6 with two decks

Stages of construction of a bath with floors

If you have any questions about the bath with floors - call us and we will consult in detail, or write

185 000 rub. and on your site will stand:

1.Srub 4x6, five-walled with an internal protes of the walls (cutting the corner “in the paw”, size 4x6 is the internal size from wall to wall)

2.Net height from floor to ceiling 2m.30cm.

3. Floor joists and ceiling beams made of hewn logs.

4.Rafter system under a gable roof with a ridge height of 2m.50cm. their boards are 50x150

5. Rafter beam protrudes beyond the walls of the log house by about 50 cm, and the roof slopes fall below the rafter beam by 15-20 cm, which allows you to get:

6.Crate- unedged board 25mm.

7. Roof covered with roofing felt (roofing with any other material is discussed).

8. Gables they are sewn up with clapboard and a frame is made in them for the windows of the “second light”

9.Finish floor in the bathhouse and on the wards - grooved floor board 38mm.

10.Two bath doors from a board 50mm. and two double windows 60x60

11. The frame is going to moss and is installed on columns 40x40x40, assembled from foundation blocks on a sand bed (sand is provided by the customer)

YOU CAN SEE YOUR LOG

BEFORE HE COMES TO YOU,

Email us

And we will send you a photo of the finished log house in the size you need.

We do not promise more than we really can. BUT! What we promised, we do WELL!

This website is for informational purposes and under no circumstances is it a public offer, determined by the provisions of Article 437(2) of the Civil Code of the Russian Federation.

The project of a bath with floors on the Good Bath
Sauna 4x6 with decks - an ideal house for an empty lot from the Good Bath


Bath with floorboards.

From our point of view, the most competent project for starting the development of the site is a bathhouse with planks, the size of the log house can be 6x4 and 6x6 and the one that the owner of his site wishes. You immediately get a comfortable house where you can live quite comfortably and without any haste start thinking about and building the main house. After the house is built and the bath (after finishing) begins to fulfill its main purpose, the space above the steam room and washing room will become a cozy sleeping place for guests.

A bathhouse with planks looks the same as a bathhouse with an attic, only in this case the rafters are made of 50x150 boards. On such even rafters, it is easy to insulate the roof and sheathe it with clapboard. If you add a porch, then, if desired, a blanket can be made above the porch.

OPTION IN BAR 150x150 mm from 180,000 rubles

OPTION IN LOG f 24-26 from 266,000 rubles

Total 266,000 rubles. and on your site there will be a bath processed under a planer:

1. Log cabin 4x6, five-walled (cutting the corner "into the bowl", size 4x6 is the size along the axes)

2. Net height from floor to ceiling 2m.20cm.

3. Ceiling beams made of hewn logs (floor beams at the request of the customer).

4. Rafter system for a gable roof with a ridge height of 2m.50cm. their boards are 50x150

5. The rafter beam protrudes from the walls of the log house by about 50 cm, and the roof slopes fall below the rafter beam by 15-20 cm, which allows you to get:

a). Pretty cute appearance.

b). Lowered roof slopes protect walls from rain

c). Near the wall it turns out approximately 70cm. a dry space where you can make a woodpile.

6. Lathing - unedged board 25mm. (at the request of the customer, you can install edged)

7. The roof is covered with roofing material (roofing with any other material is discussed).

8. Gables chopped log (discussed - they are sewn up with clapboard and a frame is made in them for the windows of the “second light)”

9. Finishing floor in the bathhouse and on the wards - floorboard 38mm.

10. Two bath doors from the board.

11. Log cabin is going to tow

12. Installed on posts 40x40x40, assembled from foundation blocks for sand bedding (sand is provided by the customer). Strip foundation by prior arrangement

Any changes at your request are possible.

Bath with curtains
From our point of view, the most competent project for starting the development of the site is a bathhouse with decks, the size of the log house can be 6x4 and 6x6 and the one that the owner of his site wishes. You immediately get a comfortable house where you can live quite comfortably and without any haste start thinking about and building the main house.



The acquisition of an empty land plot opens up excellent prospects for its development. You can build a house, a bathhouse, a garage and a greenhouse.

But you have to start with one thing.

Photo of a bath with a floor

A bath with floors will be a great choice for the first building, because it:

  • The opportunity to experience the delights of using your own land. After all, a personal steam room is the dream of many.
  • Housing at minimal cost and in a short time. The construction of a full-fledged large house can drag on for many years and require very high costs.

Structural features

Rest on the floors

In such a building there is no horizontally hemmed ceiling of the bath. And the steam room and washing room are covered on top with floorboards. The mattresses located on them will become a wonderful place for rest and overnight stay for the entire time of the construction of the main house or for the period of visiting the dacha. A staircase is installed for the convenience of visiting.

Beds with a ladder attached to them

Tip: Be sure to take care of high-quality ventilation under the roof.
Otherwise, during the operation of the sauna stove, it will be too stuffy and hot there.

Polats for a bath significantly increase its functionality at minimal cost.

In order to save the family budget, all construction work can be done by hand. To do this, we will consider their phased implementation.

Tape foundation for a bath

Installation of tape or pile type of the basis is possible. Pile comes out cheaper and is possible for implementation in sloping or lowland areas. But the strip foundation for the bath is more durable and has increased thermal insulation, which is especially welcome when planning a heat-loving bath. Consider the steps of its bookmark.

  • We prepare the ground, removing all debris and removing the top layer of vegetation.
  • We apply the markup with the help of wedges and a cord. We hammer the wedges in the corners of the future building and pull the cord between them.
  • According to the markup, we dig a trench half a meter deep and ten centimeters wide more than the thickness of the planned walls.

Tip: under internal partitions, a trench can be dug flush with the walls in order to save money, since they still do not have a load-bearing load.

  • We make a fifteen-centimeter gravel pillow, carefully ramming it.
  • We put wooden formwork on the sides.
  • We install reinforced rods on the bottom.
  • We fill with concrete.
  • Cover with foil and pour water for a month until completely solidified.

Construction of a log house

A log cabin is a primordially traditional structure for a bath, and we will analyze its construction further.

Material and cutting method

The best and most common material is pine, due to its strength, water resistance and low thermal conductivity. The logs themselves should be chosen with a diameter of about 25 cm.

This provides two benefits:

  • The net area is 4 m by 6 m.
  • Ease of subsequent interior finishing.

Tip: for the rest room, you can pick up round logs.
This will give a natural look to the interior, increasing unity with nature.

Steam room and washing

Steam room in the bath

We divide the six-meter wall of the building into segments of 2.5 m and 3.5 m. We leave most of it under the rest room of the bath, and divide the smaller one again, but already under the steam room and washing room. In them, the logs must be necessarily hewn with high quality, since further sheathing with insulation and waterproofing will be carried out.

To create floors above these two rooms, proceed as follows:

  1. We make a net height of 2.3 m.
  2. Lay sanded boards over them, getting 12 m 2 of additional area under the roof.
  3. We make a skate two and a half meters.
  4. We install the rafters from boards with a section of 50 mm by 150 mm, while we release them half a meter from under the log house, and lower the roof slope by 20 cm.
    This will provide several benefits:
  • Attractive rooftop interior.
  • Protection of walls from falling precipitation.
  • About seventy centimeters of dry space to create a woodpile.

Do-it-yourself roof installation

In order to save money, you can initially cover the roof with ordinary roofing material. The price is low and it is easy to use.

With a larger budget, you can first lay a plastic film and install any roofing material on top of your taste.

The flooring can be made of wood or concrete. The wooden floor will look more aesthetically pleasing, complementing the overall natural composition.

  • We lay thick beams on the foundation.
  • On them we install a draft layer of unplaned boards with a thickness of 25 mm.

Installation of the subfloor in the bath

  • We fasten the lags from above.
  • Between the lags we lay insulation and waterproofing.

Insulation of the underground in the bath

  • We create the finishing layer from a grooved board of 38 mm. We also use it for mounting floors.

Some time after the construction of the building, the log house will shrink, and then it will be possible to move on to the external and internal decoration to your liking.

Conclusion

Is it difficult to make a choice between building a bathhouse or a residential building on a new site? Build a bath with floors! You will get both the opportunity to take a steam bath and a place to stay while the long-term construction of the main housing is underway.

Finished wooden bath

Bath with floors - optimal use of a small area
Sauna with floors: do-it-yourself video installation instructions, price, photo



Sauna from a log house 6x4 “into a bowl” with decks and a veranda 2x4

What is a bath with decks?

In an ordinary bath, in the dressing room, they do not make a ceiling. The ceiling is only in the bath-washing department. And floorboards are laid on the ceiling above the steam room with a washing room - this is the bed.

The general ceiling of the entire bath, which will repeat the shape of the roof, is hemmed along the rafters over the entire roof area and insulated.

Polats make it possible to get additional space in a one-story bath, such as mezzanines. On the floors you can make a place to relax or store some things.

For the construction of floors, it is required that the roof rafters do not rest on the external ceiling beams, but directly on the walls of the log house. The roof rafters in this case are cut into the walls of the log house and are called wall rafters. Then the ceiling beams can only be made above the bath and washing compartment. And in the rest room they can not be installed. This makes it possible to make a ladder for climbing on the floor.

A bath with floors has its own characteristics:

  • It is more difficult to heat the entire bathhouse, as additional volume is added under the roof.
  • Warm air accumulates under the roof, and it will be warmer on the floors than below.
  • In the rest room, the ceiling is much higher than in the bath-washing department.
  • We have an additional area (not a cold attic) for sleeping or storing things.

A set of lumber for a bathhouse 6x4 from a log house "into a bowl", with boards and a veranda with a chopped "skirt"

(the set is included in the bath price)

  • Log cabin five-wall ( the fifth wall is cut with a cut outward), cutting corners “into a bowl”, the walls inside are not hewn (round timber), logs are processed with a scraper. The diameter of the log in the log house is at least 22 cm.
  • The log frame of the veranda (the logs of the lower and upper crowns are solid, produced for 2 m), the log “skirt” of the extension with three racks around the entire perimeter of the veranda is raised by 1m(in the photo the left wall is deaf to the ceiling).
  • Ceiling and floor logs - a log, hewn from two sides (carriage). The distance between the lags in the log house is 80 cm.
  • The rafter system is a beam 150x50, the height in the ridge is up to 2.5 m. The rafters are wall-mounted, installed in increments of 60 cm (under the insulation).
  • Roof sheathing - edged board of the second grade 25 mm, the roof is covered with roofing material.
  • Roof gables - lining 22 mm, timber 150x50 on the gable frame.
  • The net height of the first floor from floor to ceiling is 2.10 m.
  • Mezhventsovy insulation - moss or tow, nails, staples.
  • Columnar foundation of blocks 20x20x40 cm on a sand cushion.

The price of a bath 6x4 with a veranda 2x4 with a chopped skirt, with battens, with a set of lumber, delivery and assembly 316000 rub.

Bath from a log house 6x4 - in a bowl - with decks and a veranda 2x4
The price of a bathhouse in a bowl with log cabins 6x4 with a veranda with a set of materials, delivery and assembly. The project, the layout of the bath with a log cabin 6x4 with a veranda.

The acquisition of an empty land plot opens up excellent prospects for its development. You can build a house, a bathhouse, a garage and a greenhouse.

But you have to start with one thing.

A bath with floors will be a great choice for the first building, because it:

  • The opportunity to experience the delights of using your own land. After all, a personal steam room is the dream of many.
  • Housing at minimal cost and in a short time. The construction of a full-fledged large house can drag on for many years and require very high costs.

Structural features

In such a building there is no horizontal. And the steam room and washing room are covered on top with floorboards. The mattresses located on them will become a wonderful place for rest and overnight stay for the entire time of the construction of the main house or for the period of visiting the dacha. A staircase is installed for the convenience of visiting..

Tip: Be sure to take care of high-quality ventilation under the roof.
Otherwise, during the operation of the sauna stove, it will be too stuffy and hot there.

Polats for a bath significantly increase its functionality at minimal cost.

In order to save the family budget, all construction work can be done by hand. To do this, we will consider their phased implementation.

Foundation

Installation of tape or pile type of the basis is possible. Pile comes out cheaper and is possible for implementation in sloping or lowland areas. But it also has increased thermal insulation, which is especially welcome when planning a heat-loving bath. Consider the steps of its bookmark.

Instruction:

  • We prepare the ground, removing all debris and removing the top layer of vegetation.
  • We apply the markup with the help of wedges and a cord. We hammer the wedges in the corners of the future building and pull the cord between them.
  • According to the markup, we dig a trench half a meter deep and ten centimeters wide more than the thickness of the planned walls.

Tip: under internal partitions, a trench can be dug flush with the walls in order to save money, since they still do not have a load-bearing load.

  • We make a fifteen-centimeter gravel pillow, carefully ramming it.
  • We put wooden formwork on the sides.
  • We install reinforced rods on the bottom.
  • We fill with concrete.
  • Cover with foil and pour water for a month until completely solidified.

Construction of a log house

A log cabin is a primordially traditional structure for a bath, and we will analyze its construction further.

Material and cutting method

The best and most common material is pine, due to its strength, water resistance and low thermal conductivity. The logs themselves should be chosen with a diameter of about 25 cm.

This provides two benefits:

  • The net area is 4 m by 6 m.
  • Ease of subsequent interior finishing.

Tip: for the rest room, you can pick up round logs.
This will give a natural look to the interior, increasing unity with nature.

Steam room and washing

We divide the six-meter wall of the building into segments of 2.5 m and 3.5 m. We will divide the largest part, and divide the smaller one again, but already under the steam room and washing. In them, the logs must be necessarily hewn with high quality, since further sheathing with insulation and waterproofing will be carried out.

To create floors above these two rooms, proceed as follows:

  1. We make a net height of 2.3 m.
  2. Lay sanded boards over them, getting 12 m 2 of additional area under the roof.
  3. We make a skate two and a half meters.
  4. We install the rafters from boards with a section of 50 mm by 150 mm, while we release them half a meter from under the log house, and lower the roof slope by 20 cm.
    This will provide several benefits:
    • Attractive rooftop interior.
    • Protection of walls from falling precipitation.
    • About seventy centimeters of dry space to create a woodpile.

Roof

In order to save money, you can initially cover the roof with ordinary roofing material. The price is low and it is easy to use.

With a larger budget, you can first lay a plastic film and install any roofing material on top of your taste.

Floor

The flooring can be made of wood or concrete. The wooden floor will look more aesthetically pleasing, complementing the overall natural composition.

Means:

  • We lay thick beams on the foundation.
  • On them we install a draft layer of unplaned boards with a thickness of 25 mm.

  • We fasten the lags from above.
  • Between the lags we lay insulation and waterproofing.

  • We create the finishing layer from a grooved board of 38 mm. We also use it for mounting floors.

Some time after the construction of the building, the log house will shrink, and then it will be possible to move on to the external and internal decoration to your liking.

Conclusion

Is it difficult to make a choice between building a bathhouse or a residential building on a new site? Build a bath with floors! You will get both the opportunity to take a steam bath and a place to stay while the long-term construction of the main housing is underway.

The video in this article will provide you with additional materials. Make the best use of your site!

In an ordinary bath, in the dressing room, they do not make a ceiling. The ceiling is only in the bath-washing department. And floorboards are laid on the ceiling above the steam room from the washing room - this is the bed.

The general ceiling of the entire bath, which will repeat the shape of the roof, is hemmed along the rafters over the entire roof area and insulated.

Polats make it possible to get additional space in a one-story bath, such as mezzanines. On the floors you can make a place to relax or store some things.

For the construction of floors, it is required that the roof rafters do not rest on the external ceiling beams, but directly on the walls of the log house. The roof rafters in this case are cut into the walls of the log house and are called wall rafters. Then the ceiling beams can only be made above the bath and washing compartment. And in the rest room they can not be installed. This makes it possible to make a ladder for climbing on the floor.

A bath with floors has its own characteristics:

  • It is more difficult to heat the entire bathhouse, as additional volume is added under the roof.
  • Warm air accumulates under the roof, and it will be warmer on the floors than below.
  • In the rest room, the ceiling is much higher than in the bath-washing department.
  • We have an additional area (not a cold attic) for sleeping or storing things.

A set of lumber for a bathhouse 6x4 from a log house "into a bowl", with boards and a veranda with a chopped "skirt"

(the set is included in the bath price)

The price of a bath 6x4 with a veranda 2x4 with a chopped skirt, with battens, with a set of lumber, delivery and assembly 322000 rub.

Prices for saunas with planks, with a chopped veranda skirt from a log house, cutting corners "into a bowl"

Delivery of a log house with a set, unloading and assembly are included in the price indicated in the table

SIZE
(m x m)
4x4+2 5x4+2 6x4+2 5x5+2 5х6+2 6x6+2
PRICE
(thousand roubles.)
262 292 322 339 383 449

Option for planning a bath 6x4 with decks (log house "into a bowl")

The price includes such a veranda Here on the veranda one wall is deaf to the ceiling