Board game "Fantastic gymnastics." Making dynamic toy "Gymnast" Wooden Toy Gymnast on the horizontal bar

Iron harden steel, and steel hardens the spirit. The soul, hardened with Steel, formed a strong steel spirit of our magnificent gymnast, who performs on the crossbar. "Street Workout", as popular street workouts, capture the attention of everyone who has ever watched the performance of the Turkman. Let's try to reproduce one of them from the easiest girlfriend.

The final look of the crafts.

To create such a mobile toy, you will need:
1. Wire with a total length of 50 cm. It can be an aluminum wire in isolation, or copper - which is.
2. Floors.
3. Little Passatages and Pliers.
4. Rule, plastic cap from handle.
5. Sandpaper, cheerful or bulgaria with a grinding disk.
6. Round thin puffl.
7. A small nail with a thickness with wiring without insulation or a drill with a drill of a similar thickness.
8. Stove / Candle / Air / Plate.

Work begins with the preparation of aluminum wire. From it you need to remove isolation. This can be done in any available way. For example, burn insulation: in the stove, in the burner, above the candle. If there is a stove, it is enough just to omit the wire into the fire, and it is easy and quickly burns.

The burnt isolation is removed by pliers. Then the impressions need to cut off the wiring with a length of 14 cm. Thus, it is necessary to cut only 3 segments of aluminum wiring.

Black and charred wire is cleaned by eats.

Cuts of segments need to be stupid more diligently: aluminum should become light and clean.

Instead of the fun, you can use a grinder with a grinding disk for metal.

Now proceed to creating holes in the cap from the handle with the help of nail and pliers.

The nail must be bare in the furnace or use the flame of candles, electric stoves, gas burner.

After that, you need to try to pierce the cap throughout the upper part - for the hands of the gymnast. If it does not work the first time, then it is necessary to reap the nail again and again.

The same needs to be done to pierce the bottom of the cap - for the legs.

The decoration of the head is happening as follows: the excess elongated part of the cap must be removed with impositions. It turns out a head with a nose.

We proceed to the very responsible point - the assembly: the first wire is inhabited through the top of the cap.

With the help of small passas forming the hands of the turnstile.

Properly installed on the Hand Case:

Similarly, legs are formed. At the same time, you need to pay special attention to the angular bends.

Now you need to bend your hands, and bite up too much. The length of the hand together with the elbow should be a little longer than the body.

Attaching hands to the horizontal manist occurs with the help of bustard. First, the end of the wire must be beaten, and then rounded and tightly clamp to the crossbar.

It remains to bend the feet of the foot athlete - and the toy is ready!

The final look of the crafts.

What attractive is this model of turnstile?
1. To create a toy is not at all necessary to spend money: everything you need to work can be found at home.
2. Even a child can make such simplicity.
3. It is possible to decorate the gymnast and color paper and plasticine. A large spectrum has been created to embody the most bold fantasy.
2. Due to the simple structure, the gymnast is very movable by its design.
3. All lovers of "Street Workout" can play with it, regardless of gender and age.
4. And the compound of maneuvers, the dynamics of movements and grace of the acting acrobatic elements can be able to template the heart and the imagination of anyone who will see a turnstile in action.

Tatyana Titova

I bring to your attention a surprise toy "Gymnast on the horizontal bar" made of clothespins and a throwing material. The toy will bring your child a lot of positive emotions. At the same time, in the process of making crafts from the cast material, the child along with technical skills develop independence of thinking, creativity, artistic taste, the valuable qualities of the person (accuracy, purposefulness, perseverance in achieving the goal, etc.) are developing.

Purpose: For gaming motivation, directing game, gift.

Purpose:education of interest in sport, gymnastics.

Material: Plastic clothespins, cinema wire, wooden spanch, plastic covers, used disk, markers, 2 old feltwasters, sewn, scissors, nail polish.

Step-by-step description of the method of manufacture:

Stage 1.

We make bars from old markers, plastic covers, spanks and wires.

Step 1.Heat sequel and pierced the holes in the markers.

Step 2.Similarly, we make holes in the lids (small holes are tested, so you can expand with a scissors or a knife tip).

Step 3.Insert markers in the holes in the covers.

Step 4.Fill out the old plasticine the inner part of the sustainability covers.

Step 5.Install on the disk.

Step 6.We shorten the wooden skeleton and insert into the racks from markers.

Stage 2.

We make gymnasts from plastic colored clothespins.

Step 7. Covered with white varnish part of the face clothespins and draw a face with a marker.

Step 8. We cut the wire in half and insert the hands.

Craftsman "Gymnast on the horizontal bar" is ready. In gymnasts from clothespins, movable handles from wire, which can be attached to the different position: at the top below, to the sides.

The surprise is that the gymnast on the bars swing and rotates.

The toy will be interested in both younger and senior preschoolers.

How to play?

Goals of the game:

Acquisition of children to sports games;

Education in children interest in gymnastics;

Acquaintance with the appointment of BRUSEV;

Fixing orientation in space and on the plane; Development of shallow motility;

Development of connected speech.

Plots for directories:

"Sports Training"

"Sports Competition"

Gaming content:actions with plot toys with the use of items - substituents (for example, cubes as a pedestal for awarding, etc.)

Thank you for attention! I wish you creative success!

Publications on the topic:

I propose to replenish the mini-zoo with a new toy made of chestnut and a cinema wire. Crafts are available for children of middle and older.

In December 2017, a competition of joint creativity for parents and children "New Year's toy" The purpose of the competition was organized in our DWA.

Chestnuts are a beautiful natural material from which you can create many interesting crafts and toys in the joint work of children.

In the fall, children are under great impression of those changes that occur in nature. They reflect their impressions in various.

Nature gives us a huge number of interesting materials for creativity, from which you can do something beautiful and useful. Such.

A Christian legend of snowmen reached us from deep old. She says that snow is the gift of the sky, and the snowmen are angels. Them.

Homemade children's toys Always interesting. Each toy made for the child possesses the love and energy that is embedded in it during the construction. No wonder children are sometimes very careful to non-zeep toys.
Currently, there are a lot of different color and beautiful children's toys in stores, so homemade toys do very rarely. But hidden meaning in homemade technical toy Just and is the process of creating a toy, thinking, building it with your own hands using the tool. Moreover, such a process takes place jointly with someone from parents or senior brothers and sisters, especially when children are small and cannot work independently with the instrument, this is simultaneously playing the learning process.
Purchased educational toys (such as the designer "LEGO") is very good, they allow you to collect many designs, but the weak link is that everything is going from ready-made bricks - just fasten these bricks among themselves and we get a planned design.
In such a game, the initial elements of creativity disappear - the choice of materials, processing their hands using all kinds of tools until the necessary form is obtained, fastening the necessary methods, achieving the necessary function.
Therefore, a homemade toy is a truly educational toy.
In childhood, we were forced to build toys and accessories to the game for games. Many of them are undeservedly forgotten. I will remember to remember some homemade toys for boys, let them bring joy to children and their parents.

Wooden coil tractor

Such a tractor is interesting for boys 3 - 7 years old. It is made from the coil from under the thread or, as we called it - Katumchik.
On the wooden cheeks of the Katon, the deepening is neatly cut - this is a prototype of the tread on wheels or hooks on the caterpillars.

Such hooks allow tractor from the coil Clearly crawl on sofas and pillows.
The basis of the engine is rubber. Her length should be a little longer coil. The best rubber is airmodal, good rubber can be carefully spent from ordinary clothing gum. Such rubber gives a large stock of the stroke.

On the one hand, a small carnation or two is clogged into Caton. An elastic band can be hooed in one end for the carnations, and you can put a piece of matches for the carnations - then the rubberotor is fixed exactly in the center, which gives another extra stroke.

So that the rubber is spinning at a low speed, between the supporting stick (or match) and the coil's cheek is placed from the economic soap.
Its diameter should be slightly smaller than the diameter of the wheel (so as not to interfere with the movement), and the thickness is near the centimeter. The center is the hole with a diameter of 4-5 mm, for a support match - a small groove.
You can make a clutch from a bath soap - it is a little softer, it is possible from a candle or a ski paraffin. The softer the material of the flutter, the more slower slows down and, therefore, the tractor is going.
The assembly and launch of the tractor is shown on the video.

This tractor does not spoil anything and does not publish any sounds. Little growls only the child himself when he plays.

Toy "Buratino with a ring"

This toy is cut out of the 4-millimeter plywood publs.
First, a drawing is applied to the phaneer through copying, then cut down. The edges are treated with a skin, then everything is painted and covered with varnish. At the end of the nose, the little hole is drilled and a harsh thread is tied with a length of 50-70 cm. By the end of the thread, the ring is tied with a diameter of 3-7 cm.
The ring can also be chopped out of plywood or find a suitable ready.
Holding the profile of Pinocchio in hand, it is necessary to jerk threads to throw up the ring and put it on the nose. The smaller the diameter of the ring, the hard to do it.
There are several people at once, trying to score as much of the resulting throws for a certain number of attempts.

Acting model of sailboat

Being in the summer on vacation near the water, you can make a lot of pleasure to make making and launching small sailing boats.

For the manufacture of such it is enough to have with you only a sharp knife.
A suitable piece of dry wood is taken or, even better - a pine crust that sometimes falls on the river or lake. A knife is painted a housing of a boat - a flat-bottomed boat with a sharp nose and rounded feed.
The case is tested on the absence of a roll.
Then the case is made in the case - one vertical in the middle of the feed for mounting the steering wheel and another incision tip knife right in the middle of the housing along the fibers for fastening the mast.
The mast is made from a round bar, light and durable. One end of the rod is sharpened with a shovel and clogs the knife with a knife in an incision in the middle of the housing.
The steering wheel is littered from a flat pinch of a width of about about the thickness of the boat housing and a length of about one third of the housing length. The steering wheel is also clogged with a knife in an incision on the stern of the case, and the steering wheel should be all shipped into the water.
The sail is cut from Berrés using a knife. The top and at the bottom of the sail are made round holes, with the help of which the sail of the battlefield neatly satisfy on the mast.
You can equip one mast several sails.

Sails can be made of plastic bottles, and the body of the foam.
You can build frigate, equipping the ship by three masts and a lot of sails. The main thing is that it does not turn to the severity of the snap and tolerate well.
After several buildings, experience and ships comes well hold the course and gain a good speed.
If there are several sailboats, you can arrange a small regatta for speed and accuracy. It is very convenient when there is a shallow closed with a reservoir, where it is possible without fear and without loss of ships to work out launches.

Paper planes

The child 5 - 7 years is usually easily controlled with scissors, and these schematic flying models of aircraft are quite capable of building themselves.

The best thing paper planes It turns out from postcards - they have good dense paper and suitable dimensions. Airplanes are well holding the shape and fly well inside the room.

Cut the model classes can be all sorts of shapes and structures, you can experience a flying wing, make two stabilizers, make wings of various sweatshirts.

Each form of the model has its own flight characteristics, its flight speed and its resistance in flight.
When building a flying model, it should be taken into account, one hundred all lines of the aircraft must be perfectly straight, that is, the paper should not be mint. Paper folds neatly stroke the nail.

The center of gravity of the model should be on the first third of the wing. The angle of the attack of the rear wings should be within 15-20 degrees, it is selected experimentally and then it turns out automatically.
A well-planning angry model should be out of a vertical peak with an extended hand and smoothly sit on the floor. The airplane, fastened up from the floor, makes a dead loop and produces a soft landing.

Gymnast on the crossbar

The basis of the toy is "n"--like bed of two wooden specks bonded in the middle of the bar.
In the top of the bed, two parallel threads stretched through the holes in the hands of the gymnast figures in the "legs up" position.
The figurine of the gymnast is cut out of a veneer or other thin material.
Hands and gymnast legs are hinged with a body with a thin wire.
In the initial state, the gymnast hangs on the threads down, and the threads are 180 degrees to the left and right of it.
If now slightly squeeze the lower ends of the crossbar, then the threads will stretch and the gymnast will make the rack on the hands. If at this moment there are ends of the crossbar at this moment, then the inertia gymnast will turn over to the other side and the threads will be twisted again, only to the other side.
Changing strength and sharpness of pressing you can get very interesting pyruets of the gymnast.

Suceeded with a rubber system

Creature suceeded with a rubber systemEven very simple, already the process of creating equipment. Here there are already trees, screws and brackets, there is something to think about and make.
The simplest ship-seeker is a wooden boat with a rhubber.

The body of the boat is painted from a wooden plate, cutting out a suitable bar or a piece of polyfoam. Next we build a rubber engine.
To operate the screw from a tin, we make a bracket with a tube for the shaft (we rock a nail) and flexing the ears for fastening. The bracket can be attached by cloves or small self-drawing.
The screw cut out from the tinned tin, in the middle of the axis from the stationery clips and bend the blades of the screw.
Then we put on the axis of the bead as a bearing, insert the axis into the bracket and bend the hook.
Ahead of the case smooth the wire hook for gum. The rubberotor is made from aircraft or fishing gum. The number of gum is selected by an experimental way. In the free position, the rubberotor should be saved at about half the length of rubber. Rubber ends can be covered with threads by inserting rope loops.
Feather steering boat should be located right in the center of the screw. The axis on which the feather of the steering is kept, should provide a steering wheel of at least 45 degrees, then the model can be allowed on an arc.
For the convenience of the rhubber plant, instead of a hook in the nose body, you can put a nasal bracket with a fixed handle.
You can build a submarine on the rhubbinder, which can be immersed on the depth of meter and even more.

So that the submarine on the go was immersed in water, she needs the depths and a very small positive buoyancy. Two pairs of depth steering is also made of tin.
To regulate buoyancy, we use flat lead weights. We achieve that only the cutting of the boat is visible on the water. The differential must be zero, that is, the boat should not peck down nor nor feed.
Before adjusting the buoyancy, the submarine must be painted, otherwise after several launches of wood wet and the submarine will forever go under the water.
The longer the housing of the shipyard with the rubber coaster, the greater the reserve of the stroke. Also on the reserve of the course affects the quality of the running screw.

Boomerang-frame

Being in nature, you can make a very simple boomerang in two minutes - a frame of five flat wooden specks with a length of 20-25 centimeters.
For this rail, they are wooped according to the drawing. The design is kept due to the bend of the rail.
The frame take in the hand for the lower part of the central rail and thrown in a vertical position and a little up, and it, as a real boomerang, falls on the side and, making a circle, returns back.
If it knocks on a solid subject, then scattered on the part. It is cool, you can collect again.

Simple car with electric motor

The easiest car with an electric motor has a wooden frame from a plank or plywood, four wheels in pairs on two axes, no steering, transmission is straight - from a motor shaft, on which a rubber tube is dressed - right on the car rubber wheel.

The meaning of such a car is to feel the excitement of construction, see the dynamics and power of the electric motor, study the foundations of electrical engineering.
The wheels of the model are taken ready from a suitable toy, the axes are made from cycling spokes. The mounting brackets of the axes are cut out of fasten and fasten with self-draws or screws.
The electric motor is attached to the bracket to the frame.
A luck will be easier to fasten the electric motor on a non-rigid elastic loop bracket, then the clutch with the wheel will be more reliable.
The car is powered by a double wire (from any low-voltage adapter). Batteries and stop-back switch are collected in any plastic box of suitable sizes.
You can play, just running over the car, but you can make a circular track and secure the wire in the center of the circle.
Developing the interest of the child, you can design a stroke control with it, steering, and then it myself will design steeply managed automodels and disassemble your favorite car.

Two katonchik gun

Children's gun is going out of 2 wooden katonchiks.
One of the ends of the first Cathon is grinning straight, leaving the fly, the lower edge is cut to the level of the middle, and the neckline is made in the upper part. It will be a gun barrel with a sewer.
The second Caton is used unchanged. It will be the wheels of the gun.
You still need a piece of rail 2cm width and a thickness of 4-6 mm, the length is about half the length of the Caton. It will be a kind of emphasis and hook for a shrom.

The most complex part in the cannon is a shrom. The pushing part should be round and without friction to enter the trunk. Length is a little shorter of the trunk of the gun.
Rear: width - in the width of the stop, height is 1-2 mm, the height is 2-3mm, but not to clinic when shooting. All the faces in contact with the barrel shield (except the top to avoid injuries), should be steep, so as not to jin. The length of the rear -2.5-3cm, on the back side a small cutout for gum. Material - Birch. Pine is also suitable, but more often falls apart when shooting.
Gathering gun on threads for sewing.
First, threads tightly tied a rubber loop by the ends on both sides. Then it is attributed to the stop and immediately tie the bottom Caton - wheels, well-tightening the threads crosswise.
We insert the ammunition and put on the back of the rubber. The gun is ready.
Shoot the pea or how to find. We bring a shore, engage for the edge of the stop, charge the pea, put in the shooting position.
Now, if you press a finger on the top of the shield, the gun will shoot.

Bow and arrows

Onions and arrows are acceptable to playing outside the city, because the arrow released from the onion is flies relatively far away.
This is not a sports bow, but a distant one for the game and workout with its techniques and shooting technique.
Onions are made of a smooth piece of willow stem with peel or versa (juniper), which is even better. A piece of barrel with a length of 50-100cm is selected the necessary stiffness to have enough strength to pull onions.
The string is made from a strong kapron thread. The string is attached at the ends of the onion into the cut-off grooves, and it is tied in a non-tentuent state.
In order to tighten the the tent, they rest on one onion to the ground, the other hand bends onion and wound into the groove to the tension to the required tension. Therefore, the groove for winding the teta must be made with a dealer with the channel for pulling.
The arrow is painted with a knife from a smooth piece of timber of specking, it is cleaving that the treatment with a knife occurs exactly on fibers. Otherwise, the arrow will not be made.

In front of the boom, a thick wooden tip is left in the form of a thickening, which is spinning so that the arrow could not bear much harm.
On the back side of the arrows, a shallow groove for the taisle is cut. The technique of shooting is the usual, the only one, with such a design, the grip of the arrow's shank is not sporty - for the guide, and the game - two fingers for the arrow shank.

Simple toy self-propelled tank with electric motor

About the same technology as for a simple car, you can build toy self-propelled tank. Such a tank is to play even more interesting, because it can overcome significant obstacles.

The speed is small, so it is convenient to work with a wired remote control.
Simple tank design does not provide its turns, only move forward-back.
The design of the transmission tank is much more complicated than the car. Here is applied a multistage gear from gear from toy machines. You can choose a suitable ready gear, and you can collect a simple gearbox yourself.
First you need to pick up gears.
The main running gear of the vague is shaped or soldered on the axis. For fastening the gear, cloves of the desired diameter are selected and dry up to the desired length.
A suitable rectangular bar of strong tree breeds is taken. It is approaching the position of the adjacent gear and, accordingly, the position of the bar.
Then we work separately with Bru. In the marked place we bring the sample gear, then try on and tip the following.
We press the bar with the gear to the running gear and secure it to the tank frame by self-draws.

When the small gear is signed on the motor shaft, the second end of the shaft must be overtaken in the odor, so as not to break the engine.
Cress the gear of the electric motor to the gearbox and the crepim clamp.
Leading shafts and sloths tank are selected from unnecessary automobiles.
With rinks, the problem is more. They can be made of gaming plastic checkers.
Drills in the centers of the holes of the hole with a diameter of 2.5-3mm, we connect two checkers with planes inside, we draw a suitable piece of PVC tubules into the holes of the PVC tubule and smooth the axis. If dimensions are met, everything keeps perfectly.
Caterpillars glue from the rubber band from the bicycle chamber, the soils can be glued with rubber, and you can sew wood from matches. Caterpillars should be jagged on rollers tank. When scrolling the caterpillars, the leading roller can be rubbed in the rosin.
Such caterpillars sometimes fall during operation, but it can be corrected by restrictive colors on the sloths. In general, full space for upgrades.
Tank superstructings can be glued from any suitable material.
If on each caterpillar tank put a separate gearbox with an electric motor, it turns out a full-featured model. The axes of rinks and sludges must be replaced by separate semi-axles for each side.
The control unit will also have to be modified to manage the two engines.

Subject:

Objectives:

educational:

Improve and develop skills and skills in fuel filling;

Learn to drink curvilinear surfaces on a template.

developing:

Develop the ability to relate new information from previously learned;

Develop creative thinking and imagination;

Development of self-control students.

educational:

Bring up accuracy, accuracy when performing work;

Continue the formation of such qualities as collectivism,

a responsibility.

Methodical equipment lesson:

1. Material - technical base:

Cabinet of Labor Training;

Tools, fixtures;

Materials;

2. Didactic support:

Workbook;

Additional literature;

Posters;

Routing;

Object of Labor: Box.

Methods for conducting lesson : verbal, visual, practical.

Interdimensional connections : Iso, drawing, history.

Type of lesson : Combined

During the classes.

I.. Organizational part:

Greeting;

Checking students' appearance;

Filling in a master magazine teacher;

Checking availability of educational and working supplies;

Hello guys!

Checking student appears

Ivan's duty officer today.

There should be nothing superfluous on the workbenches. It will take: a ruler, pencil, eraser, as well as overalls. Do everyone have everyone? Well done, ready to learn.

Actualization of knowledge.

Before you know the topic of our lesson, We will play. Your task is to solve rebuses. Ripping rebuses We will learn what tool will work and what to produce. And so, began. Well done boys. As you understood today, we will work the jigsaw and begin the manufacture of a dynamic "Gymnast" toy.

Please write down the topic of our current lesson. Making a dynamic toy "Gymnast ».

This wonderful toy is common worldwide: from South America to China. Who is her author is unknown, but, of course, it was a very talented person.

It is two long sticks that are connected in the midst of short. At the ends of long chopsticks on threads, a figurine of the gymnast was suspended. With the easiest compression of the lower ends of the sticks, the figure comes into motion, imitating the exercises of the gymnast on the crossbar.

These toys will go to the school game.

(On the Lobzik screen).

Tell me please for which the logs is designed, and from which parts is?

Lobzik- this is a hand tool with a replaceable saw blade, intended for curvilinear sawing plywood and thin boards on an internal, closed circuit, consists of a frame, handles, upper and lower clamps

Now try to formulate what you need to know and be able to .

Know : Lobzika device, safety equipment when working with a jigsaw,

Be able to : Install the Pillet, cut the curvilinear surfaces on the pattern, translate drawing through a copy across

And now let's, listen, the history of the development of artwork prepared us a small messageIvan.

History of Development of Art Dumping

(1Slide) Drinking is an old type of decorative and applied art, whose tradition is alive and in our time. Lobzik drinking is not today fashionable hobby, it's rather, call of the heart and a wonderful way to upbringing in yourself not only patience, perfection and accuracy, but also feeling beautiful!

Decoration from wood is one of the most common types of decorative and applied arts available to wide masses. Masters - Dippers create wonderful patterns and drawings on the tree, and also manufactures artistically decorated products adorning our life. (Vases, boxes, clocks, various stands, etc.)

(2Slide) ANDthe stories of the art sawing takes the origins of the II half of the XIX century, perhaps each time. Options for drawings, ornaments, products are so wide and diverse as the master can afford.

(3 slide) Art sawning from plywood turned out of the openwork, slit and house thread, which distinguishes it only with material, plywood, and the lack of a cutter. In case of artistic drinking from plywood edges and ribs, only finishing and handling fine-grained grinding paper are served.

(4 slide) Currently there are 4 main types of artistic wood threads:

Geometric;

Embossed;

Sculptural;

Rubber.

From the slit thread was formed art sawning from plywood.

(5 slide) The main sign of the rubber thread is the removal of the background, the separation of the workpiece through.

A widespread spread of a slit carving was due to the fact that it is the least laboriousness, simple design technique and therefore is available to anyone, even children.

(6 slide) From the second halfXIX. Century from the central regions of the Russian Empire began to move the Russian and Ukrainian peasants to the east, including Kazakhstan. After the resettlement, they founded new villages here. On the territory of our district were founded: Nadezhdanka, Terentiyevka, Verenka, and others. Migrants together with them moved their culture, including the house thread.

(7 slide) The tool with which the drinking occurs is called a jigsaw. The history of the emergence and development of this tool goes to the distant centuries and the countries!

Today, manual jigsik is not forgotten, he is improving and new models of jigsaws appear.

(8 slide) The first similar patented tool appeared in 1876 and was called the pilot of the Bul.

(9 slide) This looked like a stationary jigsaw with a foot drive.

(10 slide) Modern stationary jigsaw with an electric motor.

(11 slide) Volume products made in technology lessons.

As I already said Today, in the lesson you will make a dynamic "Gymnast" toy. Look at the screen.

And tell me what major criteria is obliged to rely on anyone who is going to produce a particular product:

· Strength

· Aesthetics

· Material intensity

· Practicality in use

· Technoism

· Low time consideration

· Original form

· Accessibility of material

· The possibility of mass production

We will perform practical work in pairs, so let me share you on the pair.

Before proceeding with practical work, let's get acquainted with the procedure for execution. (On the screen)

3.Practic work: Making a dynamic toy. "Gymnast"

3.1. Following instruction:

Message to the name of practical work;

Clarification of practical work tasks;

Familiarization with the object of labor;

Familiarization with teaching and technical documentation Instructing on technology card

Stages of work:

Translation of the drawing on the material;

Lobzik preparation;

Installation of the epippled table;

Drinking;

Stripping product;

Drawing drawing on the product;

Safety Instructions:

1. The turn of the jigsaw and seer with reliably fixed and good handles

2. Easy to mount a piping table for the workbench

3. Shopping the pink in the frame jigsaw

4. Do not make sharp movements with a jigsaw when drinking, not bend low above the workpiece

Fizminutka (video) Fizkultminutka:

– Guys, you probably tired a little? Let's interrupt with you and make a small workout. Set aside tools and stand near your jobs. See on the screen and repeat.

For your eyes: Look to the left, right, up, down, on the tip of your nose, brightening your eyes clockwise and against;

For the neck: tilt head left, right, forward, back, rotation heads in one direction and to another;

For a shoulder belt: Hands on the shoulders - circular movements shoulders;

For hand brushes: circular movements with hands, bending - extension of fingers in a fist;

For muscles of the back: pulling the tilt of the body back and tilt forward with the touch of the hands of the socks of shoes;

For the muscles of the legs: squatting 5-8 times.

And most importantly, in order to work well and efficiently, we must remember the Japanese proverb "Hurly hurry." And what similar Russian proverbs do you know?

"Hurry - people mockery"

3.2. Summage of students

Current Instructions (Targets):

Proper jigsaw setting;

Compliance with pipe sawing by the jigsaw;

Observance of product stripping techniques;

Compliance with safety regulations during operation.

3.3. Including instruction:

Analysis of independent work by students;

Analysis of typical errors;

4. Cleaning jobs.

5. Summing up the lesson.

Message of the teacher about the achievement of the lesson's goals;

An objective assessment of labor results;

Relationship.

The mark "5" is set if the product is performed exactly according to the drawing; All sizes are sustained; The finish is made in accordance with the requirements of the instruction card or sample.

Mark "4" is set if the product is made according to the drawing, the size is descended, but the quality of the finish is below the desired one.

Mark "3" are set if the product is made according to a drawing with small deviations; The quality of the finish is satisfactory.

The mark "2" is set if the product is made with deviations from the drawing, does not correspond to the sample. Additional refinement cannot lead to the possibility of using the product.

Setting assessments in the classroom and in the diaries of students;

Homework; (Compose a test on the topic studied).

Cleaning jobs.

7. Legal reflexion . Reception "Traffic light".

A green circle - liked, everything was clear;

A yellow circle - liked it, but there are questions;

A red circle - I did not like it, everything was not clear.

Self-analysis lesson technology
Theme lesson: Making a dynamic toy "Gymnast"

The lesson was carried out in a combined workshop for the processing of metal and wood.
The purpose of the lesson:improve the skills and skills of the workload, learn how to cut the curvilinear surfaces on the template.

I believe that the combined type of classes corresponds to this topic. In accordance with the current requirements of classes on technology, 30% of the time is assigned to theory and 70% for practical work.
Everything has been prepared for classes - there are the necessary tools Presentation.

The organizational part of the lesson was performed clearly, the transition to the next stage of the lesson smooth, logical. The actualization of previous knowledge was aimed at making necessary, necessary, in addition, also the psychological preparation of students to the topic studied. This stage has given the opportunity to assess the degree of readiness to the perception of a new material.
The topic of the lesson was communicated and together with students identifies goals. A presentation was used to organize attention.

The formation of new knowledge was carried out by the method of the story, conversation. Material made consistently. During the explanation, a demonstration of actions was conducted. During the lesson, a benevolent tone was preserved. The pace of work is normal. The material is selected effectively in accordance with the objectives and objectives of the lesson. Questions and tasks contributed to a deeper assimilation of the material.

Students are taught to work independently, carrying out self and mutual control.
The introductory instruction was carried out in an accessible form, with a demonstration of operations and receptions, used visibility during the instruction. Current briefing. All students were involved in practical work, jobs were organized. Practical work was performed individually, under the supervision of the teacher.

The consolidation of knowledge was carried out in the form of a crossword puzzle, showed assimilation of the studied material.

When conducting the lesson, everyone gained d / s, the estimates are commented, (exhibited with the help of students).
The goals of classes are achieved, time is distributed rationally, the occupation was carried out according to plan.

Board game "Fantastic Gymnastic" (Fantastic Gymnastics) from Hasbro Gaming - new fascinating entertainment for a child or a whole company of kids to the basis of this game is the incredibly popular and relevant to date fun, the meaning of which is to be thrown into the air it got up Exactly on Rodyshko, for example, a bottle of water, etc. It is possible to say with due confident that Fantastic Gymnastics will cause genuine interest not only in children, but also in adults!

To start the game, you must first make a simple build of the horizontal bar. Included you will find: figurine of the gymnast; crossbar fixed on two racks; base with buttons for spinning and jumping gymnast; Special mat (like Mata), to which your athlete will land; Detailed instructions, including the tournament grid. When the assembly of the toy sportsman will be completed, and the gymnast is fixed on the crossbar, we can safely begin the competition.

The essence of the game "Fantastic gymnastics" is that your gymnast makes a certain number of revolutions in the air, and then landed clearly to the legs, having received the highest ball for the difficult element! In order to carefully spin the figure, you must press the yellow button at a certain pace. As soon as you understand that the gymnast is ready to let go of the hands and make a dizzying jump, press the red button immediately, so the figure will immediately be pulled off from the crossbar! It is worth noting that it is for such a spectacular "purely" trick, and even with the maximum number of revolutions in the air, not so simple. It is necessary to be patient to develop a dexterity and purchase a snorkeeper, then the impeccable performance of an incredible gymnastic element will only be the case of equipment!

Buy the board game "Fantastic Gymnastics" / Fantastic Gymnastics from the brand Hasbro Gaming at the lowest price you can in our online store with delivery in Moscow, St. Petersburg and all of Russia!