Two-round wall gas bucky: instruction, installation. Gas Copper Baxi Instruction Gas Boiler Bakci Hinged Two-Building Instructions

Tariff growth and the inaccessibility of centralized resource highways in remote areas contribute to the development of autonomous systems for providing private houses with heat and hot water.

The most successful options are boilers that ensure heating of hot water, power supply and circulation of the coolant in heating circuits or warm floor systems.

There are many firms engaged in the production of heat engineering equipment, which develop and improve the design of heating units.

Gas plants that are noticeably dominated over other types of heating boilers are considered the most efficient and economical.

The most important operational procedure is the setting that will be considered on the example of the Gas boilers of the Italian company BAXI.

Mounting the boiler consists of several stages:

Installing the water filter on the pipe, bringing water to the GVS system. It is necessary to deliver cutting valves on both sides, ensuring the possibility of dismantling the filter for maintenance, repair or replacement.
Placing an aggregate in a reserved place. Outdoor devices are simply placed at the desired point of the room, the wall boilers are hung on the surface of durable walls. It is forbidden to mount on plasterboard partitions or other structures that do not have sufficient bearing capacity. Fastening to the wall is made on special brackets (sleds), which are included in the package.
All undermining pipelines are joined - gas, heat carrier direct and reverse line, DHW. A coaxial chimney is installed and attached (some models are equipped with a double chimney of the vertical type). Immediately checks the availability and quality of thrust.

The final step is to connect the boiler to the power supply network. For this, a separate outlet is needed, the power of other devices from it is prohibited by the rules of operation.

User's manual

It is primarily necessary to wash or clean the heating circuit and chimney. Any contamination is capable of violating the nominal mode of operation, which will cause accelerated wear of certain nodes and failure the entire system.

Connecting the boiler must be performed by specialists from an authorized service center, they also perform the primary setting of the installation.

Boilers pass pre-sale preparation and come to the trading network completely ready for launch. This means that no additional actions are required.

This is the application of the manufacturer, but in practice almost always have to adjust the settings in accordance with the existing technological or technical conditions. Basically, the setting consists in determining the minimum and maximum gas pressure and the temperature range, which determines the inclusion and disabling the boiler.

NOTE!

All settings must be performed by employees of service organizations. The warranty period begins from the moment of launch, and independent inclusion may be regarded as a violation of the contract with the service center, as a result of which the repair will be denied.

How to turn it on

Connecting the boiler to the power supply network is made only after the addition of all pipelines supplying water, OV and gas.

It is necessary to carefully check the correctness of the connections, special attention is paid to the gas pipeline..

Check with a soap solution Lack of leaks, when deficiencies are found to immediately correct them on their own or with the involvement of specialists of the corresponding profile. After that, the boiler can be filled with water, opening the fuel tap.

Pressure should be from 0.7 to 1 mbar. When the pressure reaches the desired value, you can start the boiler.

First start

After connecting all communications and power supply, you can turn on the boiler.

Procedure:

Open gas crane.
Install the heating and supply mode of DHW (or only DHW). These modes correspond to the designation "Winter" and "Summer".
Install the desired temperature by pressing the "+" or "-" buttons.

After that, there will be a launch of the burner and the boiler will start working. Often, after the first launch, the error and the boiler immediately pops up on the display.

This is due to the air remaining in the pipelines. By pressing the "R" button and hold it for a few seconds, the error and restart of the unit are reset. Until complete air removal, several repetitions of such a situation may occur.

Air can be released faster if you open access to the pump and weaken the screw. The procedure is performed when the power is turned off. The air will be released from under the pump cover, as soon as the water goes, the screw immediately delays and the equipment starts again.

How often should it turn on?

The inclusion frequency of the boiler depends on several factors:

The power of the unit.
The correctness of the boiler settings.
The presence of a room thermostat.

With excessive power, the installation quickly heats up and turns off. The circulation pump provides the receipt of new portions of the cooled coolant, the temperature sensor works and starts the boiler again.

Power can be reduced by programmate. It is also necessary to reconfigure the boiler, in particular - to increase the parameter F11 (waiting time before repeated) to a maximum that is 10 minutes.

The use of the thermostat can significantly increase the time between the launch of the unit, since the air cools and heats up much slower.

Temperature adjustment

To add or drop the temperature on the right and left of the display, there are "+" and "-" buttons (on older models there is a special regulator, turning clockwise The temperature rises and vice versa).

If a room thermostat is used, the adjustment is made from it, and only limit values \u200b\u200bare installed on the boiler.

When tuning the temperature, you should not change the parameters of jumps to large values. It is necessary to change the mode smoothly, give some time to overcome the inertia of the system. This will mitigate the transition to another mode and extend the service life of the boiler.

Pressure setting

To raise the pressure, the feed crane is used, and in order to drop the pressure - the trigger valve.

The optimal value is the range of 0.7-1 mbar. Typically, BAXI boilers independently support the desired value, but sometimes failures. If a constant drop is observed, which does not disappear after feeding the system, it means somewhere the leakage occurs.

This can mean either leakage of pipelines or radiators, a system of underfloor or other external elements.

Often the problem arises due to a trigger malfunction. An abnormal increase in pressure may be due to a malfunction or an open tap of feeding or damage to the expansion tank membrane.

Optimal mode of operation

The optimal mode of the boiler is described in detail in the user manual.

His parameters:

Temperature s - 70-75 °.
Water pressure is 0.7-1 mbar.
The parameters F08 and F10 are configured according to the minimum and maximum value.

The setting is performed during commissioning, additional adjustments are performed periodically during the annual maintenance or after repair work.

Self-Diagnosis

Self-diagnosis is an automatic continuous process that runs immediately when the boiler is first turned on.

It does not require any special actions and passes constantly in the background. Any error is immediately recorded by the corresponding sensor, which displays it to the display, and the control board blocks the operation of the unit. To reset the error and restart the boiler, click the "R" button and hold it for a few seconds.

Basic error codes and their decoding

Baxi (buxi) boiler errors are certain deviations from the nominal mode of operation, which are fixed by the sensors and are issued on the unit in the form of a numeric code with the letter E (ERROR).

Consider them carefully:

Error code	Type of malfunction	Decision
E01-02	Lack of heat carrier in the system (failure of the duct sensor)	System feeding, sensor replacement
E03.	No flame	Practitioners nozzles, gas supply, repair system
E04	False evidence of the presence of a flame (breaking spark on the sensor)	Removal of water drops from fees, insulation or sensor replacement
E05	Open temperature sensor	Restoration of contact
E06	CZ temperature sensor	Replacing the sensor
E07	DHW Temperature Sensor Open	Restoration of contact
E08.	KZ DHW temperature sensor	Replacing the sensor
E09.	Failure fan	Repair or Replacement Device
E10.	Failure to work smoke	Cleaning the chimney, restoring the working state of the smoke
E13	Kz duct sensor	Replacing the sensor
E15	Malfunction or refusal of control board	Repair or Replacing the Board
E16	Excess the permissible temperature of the boiler heating	Cleaning the heat exchanger from scale, feeding the system with water
E18	Overheating sensor smoke removal	Repair or sensor replacement
E27	KZ or air pressure slope	Replacing the sensor

Useful video

Read more in detail how to connect, configure and run this boiler you can in this video:

Conclusion

Carefulness and quality settings of boacies boils ensure the efficiency and durability of the equipment and the entire heating system as a whole.

The boiler operation largely depends on the gas supply mode and the specified temperature range, which, in turn, are selected on the basis of the climatic characteristics of the region and the size of the heat loss.

The main condition is the accuracy of the execution of adjustments, the absence of frequent and unskilled interference with the operation of the unit.

Competently completed setting to ensure the durability of the equipment and a comfortable microclimate indoor.

In contact with

Dynamic development of construction technologies allows many of our citizens to acquire their own home behind the city. Enjoy a small cottage or cottage becomes the norm. To live away from a noisy megalopolis, enjoy clean air and peace - that's what attracts people.

In a country house, cottage or cottage, as a rule, there are no central heating and hot water supply. This makes it impossible to constantly comfortable stay in such a house in the winter. Without full heating during the cold time, the solutions will be an autonomous heating system.

Independent heating system

Autonomous heating does not depend on heat networks. And this is perhaps the main dignity. You can adjust the temperature in the room yourself, and if necessary, turn off the heating at all. On average, for 5 years, equipment for autonomous heating is completely paid off.

Comfort, efficiency and reliability of housing is dependent on the choice of boiler. If your home is in a gasified area, it makes sense to acquire a gas boiler.

Types of boilers

Provide hot water in the house is designed by a flow gas heater. He was installed earlier in an apartment building. Now the models are improved and equipped with a gas control system and ignition.

Single-mounted gas boiler uses a small area for heating housing. It is simple, powerful, but its operation has its own characteristics:

the need to connect to chimney;
use for combustion of indoor indoor air (open combustion chamber);
the need for additional ventilation of the room.

The boiler with an open combustion chamber requires increased caution and strict adherence to fire and sanitary requirements. Among one-contacts there are boilers with a closed combustion chamber, but they are more expensive.

A double-circuit gas boiler is capable not only to heat the room, but also heat the water. One contour works for water heated, and the second is for heating.

Wall gas boilers "Baksy"

The design and design of Italian gas boilers meet the needs of modern heating. Copper Gas "Baksy Moon" can be positioned on any free wall area. He does not require a special premises for accommodation - everything that he needs for work is already provided for in the inner structure.

Mandatory certification for compliance with the safety requirements are all wall gas boilers "Baksy". Consumer reviews most often confirm the simplicity of boiler management and its safety.

The aggregates are equipped with a special system of control, which is capable of diagnosing system operation itself and take into account weather conditions. If there is a gas pressure drop in the main entrance, it will not affect the operation of the gas boiler.

Assortment of wall gas boilers "Buckuck"

Gas single-mounted boiler - only for heating at home.
Household wall gas boiler with two contours; Purpose - heating and hot water supply.
Turbated boiler with two contours. Special equipment increases the rate of internal processes - for heating and hot water supply.
The gas wall uses the released steam energy until it is transition to water.

Wall boilers with one contour

Single-mounted gas boilers are designed for heating at the house. Wall-mounted "Baksy" decided to make more functional and installed special taps for installing an additional boiler. It is possible to heat the water for household needs.

Single-mounted boilers are pretty simple. The burner, which sets up gas, placed inside a safe thermal shell. The heat that accumulates in the combustion chamber, through the heat exchanger is transmitted to the heating circuit.

Material for the manufacture of the heat exchanger is copper, cast iron or steel. This type of boilers is designed for a small power - from 14 to 31 kW. Wall-mounted baxi are small in size, made with a closed or open camera.

Double-circuit wall gas boilers

The design of the boiler provides for the presence of a heat exchanger that is connected to the heating system. Water heating occurs once in a closed cycle. On the heat exchanger, you only need to maintain the required temperature.

The heat exchanger that is connected to the water heating system, the secondary, and the new portion of the cold water periodically comes into it, so it is forced to work constantly on heating.

Types of heat exchangers on "Baksy" boilers:

Lamellar. A long curved steel tube is attacked to protect the design from high temperature, a special protective layer was applied to it.
Biometric. Another pipe smaller diameter is inserted inside the pipe. In the outer water flows for heating, water for household needs is moving along the inner.

Gas boiler Baxi Luna 3 Comfort

Perhaps the most popular and perfect is a double-circuit gas wall-mounted boiler "Baksy". Reviews, in any case, it is that. The model is considered successful and reliable. There are several reasons for this:

Installed weather-dependent automatic system.
Temperature regime for heating radiators (30-85 ° C) and separately - for water heating floor (30-45 ° C).
Self-diagnosis with the memory of recent problems and failures in work.
The liquid crystal display reflects all the necessary operating parameters.
An anti-corrosion coating is applied to the heat exchanger.

Wall double-circuit turbine boilers

The use of such boilers provides significant blue fuel savings. Turbocads are built into the system, and this allows you to get the necessary amount of heat at a lower gas consumption. The fan is additionally installed in the boiler, which injected the air from the street.

Cold air falls along a pipe embedded in another, larger diameter, which works on the output of combustion products. The design is completely sealed and eliminates the hitting of harmful toxins and gary inside the room.

Condensation wall boilers

The principle of their work is based on the laws of physics. Usually in the chamber of the boiler burns gas, and combustion products are outward. In a condensation, a slightly different procedure.

When combustion, carbon is formed its dioxide and water vapor. The installed heat exchanger cools the steam, and the energy separated uses to heat the contours. Its efficiency significantly exceeds the indicators of simple gas boilers.

Advantages of wall-mounted boilers for consumer reviews

Boats "Buckuck" with two contours with all their small size are able to cope with the heating of the room and the heating of the water in uninterrupted mode.
Water heating occurs in protocal mode, and not in a boiler room. It is much more convenient and economically.
The boiler is fully working in automatic mode. The user does not need to spend time to control the workflow of the boiler.
By choosing a wall gas boiler "Baksy", you do not need to buy related equipment. All that is necessary for the autonomous work of the boiler is provided by its design.
The size of the unit is minimal. It does not take a lot of space, so it is more often installed in the kitchen, where it coincides with the size of the wall cabinets.
If the Gas boiler "Baksy" is correctly installed, the error in its work is almost excluded. It is reliable, effective, safe and relatively inexpensive.

The main characteristics of the wall gas boilers "Baksy"

Permanent flame modulation occurs. It increases efficiency and saves gas.
In winter, at low temperatures, with a decrease in gas pressure to 5 mbar, the device is working smoothly.
It is enough to change the jets and re-set up the gas - and it will switch from natural gas to liquefied.
Stainless steel used for burner material, and this significantly increased their service life.
Installed filter at the inlet for cold water.
You can install a room thermostat or modes programmer.
Limit pressure in the heating system - 3 bar, in the DHW circuit - 8 bar.

Gas floor boilers "Baksy"

A large range and optimal consumer properties are distinguished by buxi gas boilers. Owners who have established an outdoor option of boilers indicate their smooth performance. And this is due to the excellent quality of their execution.

Gas flooring boilers "Baksy" have a built-in self-diagnostic electronic system, which controls the operating parameters and, if necessary, adjusts them in the event of a pressure drop in the highway.

Fully autonomous, without any intervention, the bucky gas boiler works. Errors in the operation of the boiler or a decrease in pressure in the pipeline lead to the operational shutdown of gas supply to the burner.

Outdoor boilers are produced in several versions. You can pick up your homes, cottages or production facilities, where it is necessary to maintain a constant temperature, the most suitable gas outdoor pottery boiler. Owners say that errors are practically excluded when connected, the models are extremely simple. Specialists in installing aggregates will argue them for the needs of the homeowner.

Assortment of outdoor gas boilers "Baksy":

Single-mounted boilers.
Double-circuit boilers.
Atmospheric boilers.
Condensation boilers.

Condensation Gas boilers "Baksy"

The principle of operation is the same as the wall boilers. The heat exchanger undergoes the process of reverse transformation of the dispersed part into the liquid. In the transition, the release of additional energy occurs, which at times increases the energy intensity of the boiler.

Atmospheric floor boilers with one contour

In the gas boiler "Baksy" for the ignition of the burner is provided by a separate source. Aggregates are used in various conditions. To increase the safety of the aggregate, made an atmospheric gas boiler "Baksy". The instruction prescribes to install it in a place where it is possible to connect the chimney, a gas pipe, heating and water supply systems.

In the atmospheric boilers, thermocouple controls the uninterrupted operation of the product. The dependence of the boiler from energy carriers is excluded, and if the burner flame went out, the intake valve is closed. Such a device was able to improve the safety of the gas boiler operation.

Atmospheric floor boilers with two contours

Gas flooring boilers, having two independent contours, warm the house and prepare hot water. Thermal energy that is produced is spent on maintaining the heat transfer regime already obtained. The periodic flow of cold portions of water makes the boiler constantly work for heating.

Gas boiler "Bacci Slim"

Copper gas "bucky Slim" Compact, independent of electricity. Made from cast iron, has an atmospheric burner and automation that will protect the use of the unit, breaking the gas valve. In the model line boiler, the gas "bucki slim" is represented by the 5th species. They differ in power.

Problems are possible, which are out of order of the bucky gas boiler. Installation instructions should always be observed.

There may be problems with the boiler when installing an incorrectly selected chimney. Profile experts insist on the installation of a coaxcal chimney, which also produces Baksy firm.

However, if you already have a proven reliable chimney, and you have no doubt about it, it is possible to connect to it. This will somewhat save the cash holder.

Easy to serve gas boilers "Buckucky Slim." User feedback indicate that if you need to clean any compartment of the unit, it can be done independently without resorting to the services of professionals.

You can easily customize the bucky gas boiler. Managing instructions are simple, and the information liquid crystal board will give an exhaustive picture of the settings. Power consumer can set himself, it is necessary to set the right program and set the necessary minimum and maximum values.

A self-diagnostic system is built into the bucky gas boiler. He himself can not only reveal the breakdown, but also eliminate in a short time. The display shows all information to adjust and set pressure in the system and the water temperature.

Safe and reliable gas boilers "Baksy". Consumer reviews

Any technique is subject to breakdowns, but everything compares in percentage ratio. Judging by the reviews of the owners, Gas boilers "Baksy" have the quality, ease of control, fully automated and do not require complex maintenance.

Complaints if they arise, then the breakdowns are insignificant and they do not always occur due to the poor performance of the boiler itself. It is necessary to monitor the chimney so that it is possible to scale on the heat exchanger possible, but this can also be quickly corrected.

Instructions for choosing a bucky gas boiler "

Be sure to ask the warranty period that is issued when buying a boiler.
The wall boiler with a capacity of 11-42 kW is suitable for heating at home with an area of \u200b\u200bup to 400 square meters. m. For the price it will be almost half cheaper than the outdoor. This is due to the design of the boiler.
If the cottage is allowed, and the boiler can be installed in a separate room, the choice can be stopped on boilers with an open combustion chamber.
A closed boiler combustion chamber is designed for residential rooms. Oxygen fence occurs through a coxic chimney. Forced or additional ventilation is not required.
The turbocharged gas boiler is environmentally friendly and economical, it can be installed in closed rooms.
If the house is planned to regularly use a bath, a bidet, a kitchen sink - a choice for a boiler with two contours.
If the project is more than one bathroom, then a single-mounted boiler is needed and an additional boiler installation.
Outdoor boilers have a greater margin of safety, they are more durable, more powerful and more productive. To install such a boiler, a special room will be required.
Due to the long service life, it is necessary to approach the installation of the boiler itself more responsibly.

Italian gas boilers "Baksy" reviews with positive estimates from users get regularly. They have proven themselves in the market safe, productive and environmentally friendly, have modern design and high-tech automation, fully justify the expectations of buyers and do not disappoint the demanding users.

If earlier in the heating equipment above all the reliability was valid, then the ability to work in automatic mode is waiting for it today.

English Holding Baxi Group, a well-known producer of gas boilers, takes into account these requirements: the aggregates produced by them due to high quality we use with good demand.

Our article will assist our advantages, the theme of which is the bucky gas boiler: instructions for use.

According to its device, TM buckci aggregates are not much different from other gas boilers. They consist of several components.

Gas Melting Device

The composition of this node includes several elements:

Gas-burner: In the most accessible models, a burner is installed with a constant power, in more expensive - with stepped adjustment. To maintain a constant temperature in the room, the automation system accounts for such burners to periodically extinguish, and then upload again. In the most expensive boaches, modulation burners are installed, the power of which is adjustable smoothly. Such burners work constantly and in the most optimal mode, so the set temperature is maintained with high accuracy.
Combined gas valve: Allows or blocks the gas supply to the burner depending on the automation devices signals.
Ignition unit: Consists of an electronic circuit and electrode. The network voltage incoming on it This block converts high frequency to high-voltage pulses, which are supplied to the electrode. As a result, a spark flashes between the electrode and burner (in some models - between the two electrodes), gas-air mixture on the burner.

Camera combustion at boilers TM bucki is closed, that is, the air is closed to it from the street. An exception is the model LUNA-3 Comfort 240i, which has an open camera.

The pipe for connecting the gas supply line is located in the middle between nozzles to connect the heating system.

Heat Exchanger

In their aggregates, the company establishes both steel and copper heat exchangers.

The second due to high thermal conductivity are more efficient.

The successful design of the heat exchanger allows you to absorb 90.8% of the heat combustion generated in the cell (some efficiency models are slightly less than - 88.7%).

In addition to the main heat exchanger in the buxi heater, another one, intended for the preparation of hot water, can be located. Such boilers are called double-circuit. Some models, for example, buxi EcoFof 24, can warm the water in an external boiler.

At the entrance to the heat exchanger, a grid filter is installed.

Expansion tank

In different models, the volume of this element can be 8 or 10 liters.

Russian manufacturers of heating equipment have a lot advanced as their equipment. Among popular firms - Condord. Users and review of characteristics, read carefully.

The home heating scheme with a gas boiler is presented.

Video on the topic

Consider the basic device of the BAXI boiler. The scheme is printed in the instruction manual for each specific model, but the main nodes will be the same.

The above is the chimney. Immediately under it installed a fan with a venturi tube and an exhaust hood for the output of combustion products. Below is the primary heat exchanger, having a radiator and coil, slightly left safety thermostat and NTC heating temperature sensor.

The center is located in the center of the combustion, inside which is worth the burner and the ignition electrodes and the ionization of the flame. A gas ramp with nozzles is connected to the modulation burner, which comes with gas valve gas.

On the right side of the heat exchanger, it turns down a pipe connected to the expansion tank and circulation pump. The pump is equipped with an automatic air bleed valve. It ends at the bottom of the drain of the drain of the coolant from the device and the pressure gauge, water from the heating system is at home.

On the left side, the pipe is lowered on which a hydraulic pressure switch is installed and the safety valve at the end. It comes out of it in the heating system. Between themselves these pipes are connected by automatic bypass.

In dual-circuit models, a secondary plate heat exchanger is additionally installed, a GVS priority sensor and a three-stage valve. A series of Baksy models Moon 3 Combi and Nulova 3 are equipped with an indirect size boiler.

Main 5 boilers are equipped with a bietermic heat exchanger, which simultaneously heats and flow water and coolant. It is implemented due to the fact that inside the tube on which the liquid flows from the heating system is another tube of a smaller diameter, which flows tap water.

An electronic control board is installed in front. In the electroke, printed in the instruction manual, it is shown to which places all the elements and the boiler sensors are connected on it. It can be sorted out how the electrical part of the equipment works.

Outside, a steel casing is installed on which the electrical control panel with the power and select mode is installed below. In modern models, a display is installed to display technical data and error codes in case of malfunction.

Principle of operation

We will understand which principle of operation of the bucky gas boiler. The coolant enters the system of the apparatus on the right tube, driven by the circulation pump. Next, he falls into the heat exchanger.

When the fluid temperature drops below the control panel installed in the settings, the gas valve supplies the fuel to the burner and the ignition electrode works. The flame lights up, which heats the heat exchanger. When heated, the coolant expands and its excess enters the expansion tank.

It turns out the coolant through the left tube, passing through the temperature sensor. When the water was heated to the exhibited level, the flow of gas in the burner is overlapped. Also adjust the work of the boiler may be a detached thermostat, in this case the cycles of the work will be tied to the room temperature.

In the two-circuit series, the three-stage valve changes the priority of DHW and heating depending on the needs of the consumer.

Three-stage bucky gas valve

The binding of such a boiler is quite simple, since all functional elements are configured and located inside the case. It is necessary to calculate the desired number of radiators, draw the scheme, and then connect them between themselves and bring all pipes to the device.

Series and their features

So that the type of boiler can be determined by the title, we will deal with marking. The symbol "F" or "Fi" indicates that the boiler is turbocharged with a combustion chamber of a closed type. Atmospheric devices have the letter "I". The word "comfort" means that the control panel includes a remote control panel, the mark "Air" says that this panel is remote.

The first digit after the name of the series reflects the generation of boilers, and the second power. For example, the Fourth-generation Baxi ECO FOUR 24 F device with a closed combustion chamber and 24 kW.

BAXI ECO FOUR 24 F Boiler

The Main 5 Series of the fifth generation is the following step in the development of the boilers BAXI MAIN FOUR 240 F. Includes three wall-mounted models with a capacity of 14, 18 and 24 kW. All of them are two-circuit due to the established Bi-Letter heat exchanger, have electronic protection against scale. Equipped with a closed combustion chamber. The configuration is very adaptive, the boiler works at a reduced gas pressure to 4 bar and electricity voltage drops from 170 to 270 V.

BAXI MAIN FOUR 240 boiler panel

The development of the Eco-Four ECO Four (ECO), ECO 4S and ECO 5 Compact. BAXI ECO Compact devices are distinguished by small dimensions due to the optimized internal location of the main nodes. They include single-circuit and double-circuit devices with a secondary stainless steel heat exchanger.

BAXI ECO COMPACT 4S boiler

The hydraulic system includes an economical circulation pump with an automatic air tension. The ruler includes 18 models with a closed and open combustion chamber with a capacity of 14 to 25 kW. Have a liquid crystal display. ECO 5 Compact devices can be connected to an integrated solar circuit.

The Baxi Four TECH line is a cheaper analogue of the Eco Four series due to plastic supply water pipes. LUNA 3 and LUNA 3 Comfort issues offer single-circuit and double-circuit devices from 24 to 31 kW. Can work on liquefied gas. The burners have continuous electronic modulation of the flame.

Boiler Baxi Four Tech

In the electronic board there is a self-diagnosis function and the possibility of weekly programming. Comfort Series is equipped with a remote control panel with a built-in room temperature sensor. The devices of LUNA 3 COMBI DHW is provided by the built-in eighty-line boiler of indirect heating from COMBI 80 stainless steel.

Floor booth boilers Slime have very compact dimensions, a stylish gray case with a black control panel and equipped with a cast-iron heat exchanger. In SLIM 2 models, an indirect heating boiler is installed by 50 or 60 liters.

The circulation pump operates in three speeds. Power range from 15 to 62 kW. It is possible to connect a programmable timer. The SLIM EF devices are equipped with a thermocouple gas automatic, which allows you to work in non-volatile mode with the natural circulation of the coolant.

In conclusion, we offer video about the device of the boiler BAXI ECO FOUR 24 F: