Do it yourself a torque swing from any means. How to make beautiful garden swings do it yourself? Attraction for children

One of the favorite children's fun - swing on the swing. There is almost every courtyard in the city of Swing. However, in the summer, children often go to grandparents in the village or take with them to the cottage. To diversify your child's holiday, you can make baby swings for giving with their own hands. Instructions, photos and schemes you will find in this article.

Swing can have a different design: from the simplest "Tarzanka" to a large swing, on which you can even lie. Further the designs of the swings that can be made independently, in order of increasing complexity, will be described.

Garden swings are very popular in the country

The simplest swing, familiar to the majority - Tarzanka. It is a durable stick attached to the rope (rope, chains) to the tree. Tarzanka is made extremely simple: a durable stick is selected about a half-meter length (you can sprinkle a piece of the cutting for shovel, robble, etc.), the rope is tied to its middle, the other end of which is attached to the thick branch of the tree. It is best to use the so-called scaffold nodes - they themselves are tightened and keep the load well. Such a swing of a child can do it yourself. Tarzanka can be improved if instead of sticking a strong board, drill in the center and skip the rope into the hole, then fasten the node.

The most simple tarzanka can be made of rope and stick

Slightly different from Tarzanka another shell - a trapezium. A trapezium is the same stick, but the rope is tied to it not in the middle, but from both edges. The rope can be solid, but two - the same length can be used. If one solid rope is used, it can be fixed on the branch of the usual loop (photo 1).

Helpful advice. It is better to choose a stick with a significant margin of strength. First, the increased strength guarantees the safety of the swing, and secondly, then you can pump small grooves in the places of fastening of the ropes so that they do not slide - it also improves safety.

Tarnace cable can be fixed between two supports

The simplest swing

The simplest swing can also be suspended on a thick branch, but it is better to make a crossbar with supports. The design of the support will be described at the end of this article.

Simple swing with soft seat

The seat is a square or rectangular board suspended in four corners. You can use Phaneur. Not far from the corners in the seats, four holes are drilled in which the rope or ryy is passed (in the fish instead of the head is the ring); If ryy is not used, the rope can be skipped through the hole and tie up the node (the thickness should be equal to the diameter of the hole), thus attaching the board on it. If rye is used, then instead of the rope can be taken a chain that trays to the Karabin fish.

You can attach the back to the seat with the same plywood to the seat. Another version of the backrest (suitable for small children) is shown in photo 2. On the ropes are put on a tree tubes up to 30-40 cm long (the same length!), After that, for every two adjacent ropes, a wand-crossbar with drilled holes along the edges is put on. This design, despite the simplicity of manufacture, is quite convenient, safe and will serve for a long time.

Note. Instead of putting on wooden tubes (not everyone can make them!) You can tie nodes on the ropes at an equal distance from the seating. Then the crossbars will stay with the help of nodes, not the tubes. It looks not as aesthetically, but it is easier to manufacture.

Helpful advice. In the manufacture of any wooden parts, the swing must be cleaned with a skin or file - it will protect your children from the head and give a more aesthetic type of product. In order for the swing to serve for a long time, they need to be covered with varnish or paint to protect against dampness.

Wooden pallets swing (pallet)

To wooden pallets, the chain or rope is fixed in the same way for four corners. The dignity of the pallets is their large size and strength: on the wide pallets it is convenient to swing standing, and you can put the mattress and swing the lying. Pallets can connect, forming large designs.

Seat swing from wooden pallets (pallet)

Swing from auto stakes

Automotive tires are strong enough, but they are well cut. The most primitive use of the auto stroke is similar to the tarzanka: a tire in a vertical position is tied to the branch of the rope, in such a swing you can sit. But such a seat is not very convenient, and his appearance is not aesthetic. This is not a reason to abandon the use of auto strokes.

Much better looks like a swing from the auto strokes tied horizontally on three or four chains. In the tire at an equal distance, four or three holes are drilled from each other, each of which rhyled and fastened with a nut. Between ryom and sidushka (and between nut and sidushka) it is useful to pave wide washers. Rocks (or chains) are boosted together to the support at one point on the steel ring.

The band cut off from the car is used instead of the board, as described above. In this case, the "ears" stripes are attached to the edges of the tire strip, for which the rope is kept or the carabiner is engaged.

From the tires you can make a variety of shapes for swing

Fabric swing on a metal frame

Swing seats can be made from a metal frame with a strong tissue stretched on it (for example, a tarpaulter). Instead of fabric, you can use weaving from the ropes. Example - swing from the hoop.

The swing from the hoop resembles a hammock: a wide and durable hoop is attached to three-four ropes, from which thin rings are going to the center, which woven Macrame technique in some semblance of the web. The scheme of weaving can be different, the main idea is that weaving withstand the weight of your child. The hoop usually turns into a foam rubber and a cloth, either flipped with a twine, so as not to inflict the child with an injury with a possible impact and for greater comfort. Instead of Macrame, you can pull to the hoop tarpaulin, as noted above.

Packs for swing. Fastening swing to supports

Supports (goats) are made of three bars, bric, boards or metal and have the appearance of the letter A: the lower ends are placed in specially dug holes and bury or concreted. The crossbar even for children's swings is better made from a metal pipe. In the absence of a pipe to goats, the beam is placed - a thick bar or a rounded log. The design should be durable and not fused. Steel supports are harvested with welding, and wooden join with screws, anchors, self-draws and metal corners.

If the seat is suspended to a metal crossbar, it is good to use rings - plastic, metal or wooden. The latter can be chopped out of the tree independently. If you bind the rope to the tube without rings, the rope can be pulled out. Then it is necessary to regularly check its strength. If there are rings, it is better to smear the places of contact rings and crossbars.

If the swing is suspended to a log or brusche, then the rings are not needed: the rope will not slide on a tree due to strong friction. Both ropes and chains can be attached to the polls (or hooks), firmly screwed into the bar or log. Wooden design elements need to be closed or painted to protect them from moisture.

Instead of a wooden crossbar with fish, you can use steel crossbars with rings welded to them. On a wooden beam, the frame can be replaced by clamps for which Karabina hang. Chains can be attached to vertical stands on an anchor with wide washers. In this case, the beam is needed only to impart the design of stability and rigidity.

Cots can be attached on chains

Chains can be attached not separately, but to connect rings: the left chains are attached to one, right - to another. Rings are also suspended on the carbines to the fish, on hooks, clamps, or welded to a metal crossbar.

Children's swing on the ropes are not such reliable

Let us dwell on two types of swing.

Chairs rocking

Rocking chair can replace the child swing. The advantages of the rocking chair can be attributed to the safety for the swinging (there is no risk of the rope of the rope) and mobility (you can put into the house, you can take it outdoors); The disadvantages are the relative complexity of the manufacture and what such a chair can give the foot standing nearby. A variety of rocking chairs can be considered wooden rocking horses. The main complexity in the manufacture of rocking chairs is the manufacture of rounded polls; For a children's rocking chair, they can be filled out of thick plywood.

Rocking chairs are safe and fit even the smallest

Horse - a rocking chair from a wood array

For the manufacture of polozov, it is necessary to draw their contours on the sheet of plywood and neatly cut the jib, after which it is cleaned with a file and sandpaper. The seat of plywood or chipboard (plywood is stronger and easier) is attached between the polishes on metal corners. It is necessary to work very carefully so that the rocking is not turned out to be a curve.

Floor rocking for kids can also be made of dense cardboard

Swing-Balancer (Eng. Seesaw).

Swing-Balancer is a long crossbar, at the ends of which seats are made. On such a swing, you can swing at least two. The simplest variant of the Balancer swing is done like this:

It is selected long (2.5 - 3 m) durable board or bar, cleaning and sandwich.
On each side, the handles are screwed from the edge. For this, on the two sides of the bar attached on the table, to which the crossbar is fitted (photo 5).
On both sides, the seats from plywood or boards are screwed or nailed, it is advisable to attach the pads to the seats to be soft.
In the ground, a thick durable post is launched in length about a meter to the depth of half meter (or concreted).
By the middle of the bar, it is screwed or nailed with a hinge, which is then fastened to the wigged post.

Another option is possible when it is lit up from thick plywood, as for the rocking chair, and are attached to the middle of the bar. Then swings become portable and can be used indoors.

Making a swing - Balancer for children

Safety

When making a swing, remember: negligence in the work may respond an injury. Be sure to choose the durable chains and ropes, check the stability of the structures. It is better to spend more time and money and make a swing stronger you need than because of the error in the calculations to become a culprit of a spoiled rest, and worse - a serious injury of a native child.

There is another interesting type of keyings - this is a swing-grasshopper. Scheme swing grasshopper

Swing for giving with their own hands

42 photos:

Reading time ≈ 10 minutes

How nice after a long working day to sit on a bench. And sometimes more pleasant to relax on the garden swing, which will give lightly swaying and soothing coolness. To buy, unfortunately, this design is not always obtained. After all, the cost of such swing is high, often translated. Therefore, let's talk about how to build garden to enjoy a pleasant relaxing in the fresh air.

Beautiful garden swings in the country

The indisputable advantages of garden swings. Varieties

In the country or in the courtyard of the country house, garden swings are an indispensable landscape design attribute. In addition to the excellent place to rest, they perform many features:

resting on them, you can easily college;
calm the nervous system;
beautiful design helps to transform the entire courtyard;
a comfortable place to work for a laptop or reading books;
they can be laid in the afternoon (especially kids);
suitable for pleasant tea drinking and conversations for a glass of wine;
children help train and develop the vestibular apparatus.

As you can see, the advantages are really huge. Therefore, it is logical that their popularity is so high among the population. The design, in fact, is not very complicated, so even a newcomer in a construction business will be able to build such swings at home.

Another advantage of its own construction is full compliance with your desires. You can decorate it yourself or decorated, choose a special shape and size. The main thing, during the construction to adhere to the instruction, then it will be necessary to work out.

Before you start making a garden swing, you need to consider what they happen. For example, for purpose:

for kids;
for adults;
for the whole family.

Depending on the location, there is:

stationary swing;
mobile swings. Convenient because you do not need to be attached to a specific place. You can easily and quickly move it to another area.

If we talk about the main materials used, then the swings are:

from wood;
metal.

The design may also be different.

Suspended.

This option is characterized by simplicity. All you need to create such a swing is the crossbar, high strength rope and seat (it is better to choose with the back).

Suspended garden swings

Frame.

Often used for children. They are strong and stable and easily moved. So at any time you can move the swing in the shadow or other place you like.

Frame garden swings

Creating on a tree requires the manufacture of the seat. Everything else is easier than simple. After all, it is not necessary to make the framework in this case. After the construction structure, it must be fixed on the tree (make sure that the branch used is durable) or the beam. A rope with a crossed joint is suitable for consolidation, the diameter of which is at least 24 mm (especially for the swings on which children will ride).

You can replace the rope with a chain suspension. So you make the whole design much stronger. So that the links of the chain did not harm the children (fingers can fall into the links) you need to put it in a suitable size of the plastic pipe. Alternatively, you can take a chain canopy with a small caliber. It is worth noting that to install a frame garden swing, you should correctly choose a place on the site, avoiding trees and various kinds of fences.

The right choice of support

Support for swing is not just an element of the design, but its main component. It will depend on her strength to depend on swing and permissible swinging. Most often material that is used for the manufacture of support is wooden bars, metal pipes and corners. For the summer, there is often enough support in the form of the letter A. To do this, build a frame of two supporting elements. Between themselves, they are connected by a transverse beam, which is installed horizontally. Its placement occurs at the level of one third of the post above the ground level.

The crossbar itself, for which the seat is hung, you need to build up to the racks that are vertically. Use bolts for fastening.

Important: Metal swings need to be fixed in the soil. Because in the process of "foot" out of the pipes, it is loosened and turned out of the ground. To prevent this, reference frames create. Alternatively, you can make concreting into the trench.

But for a stronger consolidation of the design of the tree, you need to bury the "legs" of the garden swing to a significant depth (at least one meter). You can also pour with a solution of concrete. But before concreting, it is necessary to make preparatory work. A bitumen mastic is applied to the support so that the "legs" are well soaked. It will keep the wood from the processes of rotting. At the bottom of the pit laid brick.

Video: Garden swing do it yourself from metal

Construction with their own hands of a garden swing made of metal

Metal is a durable material and heavy enough so that the entire design of the garden swing is strong and stable. Such a choice is ideal for the construction of a swing, on which teenagers and adults will ride. Also, the metal base will be more wear-resistant to large loads.

Metal garden swing

Be sure to use the drawing so that the entire installation is performed correctly. Therefore, it is further represented by step-by-step instructions so that you can build garden swings with your own hands from metal (drawings and sizes, photos will be listed below) in your country. Of course, options are selected individually. And in the photo we will show only one of the possible.

Metal Sadden Swing Drawing

The construction of this installation begins with the preparation of materials:

pipes cut in accordance with the necessary dimensions;
burzes and sharp protrusions should be removed using sandpaper.

Form. For this, the support elements must be made at an angle of 45 degrees. Then install the crossbar. It should be strictly perpendicular to the racks themselves. At this stage, use the welding machine to make all the elements as much as possible.
You need to make a deepening to secure support. To fall asleep the sand that needs to be good. Then set the support and pour a concrete solution over it. The whole design is left for at least a week so that the solution is good, and grab.
As soon as the fill dry, you can proceed to the fitting of the seat. Before installing it, you need to privar special hooks using a welding machine. The seat itself hang on ropes (high strength) or on metal beams.
The final stage is to paint all elements of the garden swing. This measure is necessary not only to impart the design of an attractive appearance. Painting it, you will save your creation from rust and corrosion. It is also possible to various decoration for your taste and fantasy.

Previous Garden Metal Swing

If you feel that this option is not under force, you can stop on a simpler instance. In this case, you need to be built in a conventional metal profile (50 mm diameter).

Drawing of a simple model of a metal swing

At the stock (transversely) to attach special metal brackets. To do this, use bearings and welding machine.
Install the seat on the suspension and attach to the design itself. Most often can be found as the stems of the metal or chain.

Simple metal swing

Creating exclusive models looks original and attracts the attention of others. It may be forged products or swings, created from channels, or rather from their cropping. Interestingly looks like a swing, made on their own.

Worn garden swing

Swing from wood

Particularly popular is precisely. After all, the tree is always popular as a building material. To build garden swings with their own trees, as well as from metal. Drawings and sizes, photos from the Internet to help you. Only it is necessary to use suitable projects, then you will get the perfect result, and the photo of the home product is confirmation.

Wooden garden swing do it yourself

These designs have their advantages:

naturalness and environmental friendliness;
presentable and original appearance;
strength (in the case of impregnation with specialized solutions and substances).

Drawing of a garden swing from a tree

The most suitable trees are birch, spruce or pine. For construction, you need:

wood post - 2 pcs.;
transverse crossbar;
rope - about six meters;
hooks or suitable suspensions;
elements for fastening the design (perfect use of bolts).

If you have a wooden bar, then the construction of a swing on four pillars will be an excellent option. But this design requires some attention and strength.

Initially, you need to make a support. Two parts from BRUSEV should be collected in the form of the letter A, as shown in the photo.
After that, you need to secure the transverse crossbar.
In order for the installation to be the most durable and reliable, you need to use short bars.
From the same BRUSEV or seat. And do not forget about the back for maximum comfort.

Beautiful garden swing

Construction of children's garden swing

The process of building a swing for children is similar to the construction of an adult. Need a detailed design scheme, drawing of sizes and places of elements for fastening. When using drawings for adults, do not forget to optimize it under children.

It is necessary to make racks. They must be the same size.
Setting the racks is carried out at a distance that directly depends on the width of the future seat.
Both traces of the transverse crossbar should be connected.
Special attention should be paid to the reliability of the compounds. To do this, you need to accurately measure the angle under which the elements of the racks that are located vertically will be connected.
It is also necessary to ensure that the transverse crossbar itself is equally removed from the ground level.
Before installing you need to roll out the trench. It creates a special pillow of rubble. There are supports. After installation, everyone is poured with concrete solution.
There is a grinding of the whole design, you also need to round the corners. It is necessary in order to make a swing safe for children.

Children's swing

Your cottage will play new paints when such a swing made in the yard will appear made by its own. It is not only useful, but also incredibly beautiful.

System of fastening elements

There are various fastening systems for garden swings, namely:

carabiner - made from such types: with a rectangular cross section (intended for beams) and with a round cross section (for BRUSEV);
anchor - the fastening type passes through;
brackets and hooks - designed for children's models;
clamps are needed for fixing in the case of hanging swing on cables.

Therefore, carefully learn the features of each system. After all, the right choice of fasteners allows you to make a swing not only durable, but also reliable.

Rope swing

The most classic models are swing from rope and logs. This option is considered the easiest for the manufacture. To implement such an idea, you will have enough four holes. As a basis, use a wide log. In the well-done holes need to turn the rope.

Rope garden swing

Using the same ropes, you need to wear a seat board. But you need to be attentive. This option is not entirely stable. To avoid the coups of the seat, make a side of four holes and thread rope in them.

Rope ends need to tighten well and tie with durable nodes. And the swing is ready to use.

Today, garden swings made by their own hands produce a gorgeous and unforgettable impression. It is only a little patience and attention. What will be the swing? Frame made of metal or mobile made of wood? Establish to you, but the swing must be enjoyable. And the most interesting about the independent facilities of the garden swing, see the video that will find below.

Video: Wooden swing

What to do children in their free time on the street? Run and play, build a house from the sand, ride a bike, drive the ball. And many kids are happy to spend time on the swing. They love to rise and drop sharply. Such swings can be made with your own hands using a rebunny material for this.

Over the course of several centuries, the swing remained a popular attraction, and not only for children, but also for adults. None of the people's walk in ancient Russia did without "flights" on these devices. At the time of the Russian Empire, they were also the poor layers of the population, and rich people. Naturally, they looked differently: the poor swore on ordinary wooden boards tied with ropes to the columns, and the swings of the rich were decorated with decorative elements, pillows, bows and ruffles. Nowadays, interest in them does not fade, they can also be seen on the courtyard sites, in many children's organizations, in country "residences".

What material is suitable for the manufacture of yard swings

Swing can be made with their own hands, using almost everything that is at hand.

Table: Benefits and Disadvantages of Different Materials

Type of material	Benefits	disadvantages
Wood	Strength. Environmental Safety. Long service life. Non-slip seats. No dependence of the temperature of their surface from weather conditions.	Exposure to rot, if there is no appropriate processing. Increased risk of offplaces and minor injuries.
Metal	High reliability. Such swings are capable of withstanding significant loads (up to 150 kg). The possibility of decorating with different details.	Corrosion exposure. High thermal conductivity of metal, which prevents the comfort of the use of swings (in the heat they are very hot, and in the frost too cold).
Plastic	The vast assortment of shapes and colors. Ease of installation (associated with a small weight of structures). No need for special care. Harmonicity of presence both in country sites and in massive complexes for children's entertainment.	A small reliability of the design compared to products from other materials. The inability to use outdoors. Exposure to the influence of strong frosts, temperature differences, high humidity. The possibility of using only younger children. Not all plastic structures withstand strong frosts, temperature differences and increased humidity.

Photo Gallery: Types of swing on the material

Wooden swings require careful antiseptic processing and surface grinding
The strength and reliability of metal structures no one disputes
Plastic children's designs can be purchased in the finished form, but they only fit the kids

Using non-standard materials

Some craftsmen can make a swing and from other materials using for this by car tires, plastic pipes, wooden pallets, and others. There are even snowboard boards, skates and other non-standard materials, such as old basin.

Photo Gallery: Creative Seats

Creating suspended swings will not take much time
In skillful hands, even snowboarding can be a useful element of children's swings.
Older children like non-standard solutions, such as tire swings
The role of the seat can perform an old spacious pelvis

Designs of swing

According to the constructive features of the swing there:

framework;
suspended;
outdoor;
transformers;
electronic type.

Age preferences for frame-type swings are children from 3 to 10 years. Such structures have a big advantage - mobility. They can be placed in any zone of the country area or playground. They are strong enough to withstand the weight of the guys of younger school age.

Suspended swings are attached to the beam-crossbar. To do this, you can use chains, ropes, ropes. Reliability increases with a strong crossbar and under the condition of competent attachment.

Outdoor structures can be used to children under 5 years old. Most often, when they are created, plastic and metal parts are combined.

For very small kids, you can make a transformer rocking chair that combines several elements at once:

chair for babies;
mini chair;
directly swing.

Modern world is impossible to imagine without electronics. There are swings equipped with a special system in which may include:

timer;
"music Center";
the device for setting the rhythm of the movements of the swing.

They should be purchased only if there is a newborn baby in your family.

Photo Gallery: Different Swing Designs

Frame swings 0 The usual type of facilities
The design of the outdoor swing provides them with the transfer to any suitable place.
Good and convenient to children in suspended swings with a back
Electronic swing and even crumbs

What functions swing can perform

Swing, despite similar functions, can be somewhat different from each other. This is connected with the design of these designs, and with their principles of work.

Who among adults does not remember the attractions like boats? This type of swing can be used to entertain both children and their parents.

There are several types of children's designs marked with one concept - swing balancers. These devices include swings:

"Libra";
"pendulum";
"Rocker".

Such a fun fun comes even for small children. With the support of an adult on the swing can ride and one year old baby.

Nowadays, manufacturers of children's structures offer a rich variety of spring devices for swinging with balancing.

Of course, the swing can be purchased in the store, but it is better to work hard and build a swing. Years will be held, but your child, who has already matured, will definitely be remembered by the minutes of "takeoff" and "falls" on the swings that you made it with your own hands.

Photo gallery: Spring structures for kids

"By seas, on the waves" - the motto of designs for children in the form of a boat
Sitting in an airplane, you can feel like a real pilot
Such a ladybug will not carry your child to heaven, but you will have fun
Spring, sitting in helicopter, please all the guys

Preparatory work

If you decide to build children's swings yourself, you should conduct preparatory work:

decide with the type of future design;
clarify the parameters;
draw a drawing;
purchase the necessary materials;
get the entire instrument.

Selection of material

The easiest design of the swing is suspended. You can make them completely wooden or combine different materials. For suspended elements, most often use metal chains, ropes, durable cord, parachute pins or rope.

As a seat, it is best to use a polished board, because it is convenient, not cracking in the cold, will not deliver discomfort in the heat and in the cold. You can apply sweater tools - old seats from chairs, chairs, etc.

If you have not one child or you often come with guests with children, you can make a balancing for two. Make them from different materials. The advantages of metal swings are in their strength, but a good welder will need for an independent structure of such a design. Wood swings make it easier, and they are less dangerous during operation.

Calculation of materials

It is easiest to make hanging swings with a metal support and wooden swing-balancer.

Materials will be needed:

2 Iron pipes for reference pillars (d \u003d 74 cm);
2 bearings;
1 metal pipe (for crossbar) with a length of 50 cm (d \u003d 150 mm);
ready solution for concreting;
apparatus for welding;
2 metal plates are not already 7 cm.

For swing-balance prepare:

any wooden material (medium length - 2.5 meters). You can take a conventional lamb, timber (thickness 40-50 mm) or a circle of about 25 cm wide.
seat boards (width - 30-40 cm, length - 45-60 cm) with a thickness of at least 30 mm.
metal rod for support.
hardware.
paint or primer.
2 Wooden handles (they can be made of a wooden rod with a diameter of 25 mm, about 60 cm long).

Street swing schemes

It is possible to facilitate the work on the manufacture of a swing, making a design scheme. The drawings are made independently (under the individual parameters) or are taken ready from different sources.

Photo gallery: examples of drawings

The design of the swing should be very stable
Based on the desirable, you can build frame swings from wood
In the diagram, be sure to indicate the dimensions of each part

Tool preparation

Depending on which design you prefer, you need to prepare:

welding machine;
drill;
a hammer;
shovel or manual drill;
screwdriver;
bulgarian;
hacksaw;
roulette;
plane.

Step-by-step instructions for the manufacture of chain and wooden seed

Prepare everything you need can be started:

There is another reliable method for fastening supports and crossbars - by welding a special design (this option is very suitable for connecting wooden structural elements).

Bearings using metal plates are mounted in the central part of the transverse crossbar. Bearings must ensure the movement of the swing in the direction of "forward / backward". Next, the actions are:

The state of the swing is to carefully monitor. It is necessary to regularly lubricate the bearings with machine oil and tinting cutting parts.

Before you offer the children to ride, test the swing yourself.

Video: how to make a swing from the profile pipe at the dacha with their own hands

How to make a swing balance for a child from a tree do it yourself

Relying on the drawings made and armed with the necessary materials, the tool, you can start assembling a tree-balance from a tree. Work is carried out in 4 stages:

installation of base;
production of a rocker-balancer;
assembly;
paint product.

The basis is the basis of reliability of construction for children. This element of the swing can be built from a wooden bar (10x15 cm), logs (20 cm), boards (not thinner 3 cm), securing them in the intended place of future swings. From the tree, the lower frame is built with a length of about 1 m and the vertical supports or racks at an angle are fixed on it (with the help of self-tapping screws).

The rocker-balancer is easiest to make a bar or a thick board.

For the entire length of the balancer (up to 2.5-3 m), 2 bars are stacked in parallel to each other, bars are placed between them (on both sides), the bars are placed (up to 1 m). The entire design of screws or waterproof glue (for carpentry work) is recorded. You can use one board.

At the edges of the rocker, the seats with handles are made, in its central part - a hole for the profile pipe.

Pens, like all other wooden parts should be perfectly smooth, so that the child does not drive into the skin in the area.

The assembly of the rocker and the base is performed using two pipes: the support and segment mounted in the center of the swing. They are combined, insert steel rod into pre-drilled holes on both pipes.

Video: how to make a tire product

Decor process

After the swing is mounted, it is necessary to take care of their appearance. It is easiest to paint them with oil paint. This method is suitable for wooden, and for metal structures. You can fantasize and make a swing particularly attractive for the children.

Do not neglect the rules for using children's swings that will help avoid injury. It is impossible:

Too closely approach them during their use by other children.
Rather standing, leaning her legs on the seat.
Twist ropes, chains or other suspended elements.
Sleep from the swings before full stops.
Sit down to one seat at once to several children.

Before exploiting swing, it is necessary to carefully examine all the nodes and compounds for their integrity and functionality. Regularly lubricate the swing, not allowing the appearance of rust and screens. Ensure that there are no acute items in the design, protruding bolts, unwelked wooden sections.

Swing do it yourself easy. The main thing to adhere to the technology of manufacturing the product and recommendations of specialists.

The construction of the swing with their own hands will make it possible to create a universal relaxing agent and will provide a full-fledged holiday in the country or in a country house.

The presence of free space on the country's country or the preservation site gives a lot of advantages. Some prefer to break the garden in its place and enjoy the beneficial properties of vegetables grown with their own hands. Others prefer to equip it under the recreation area, building a garden canopy and putting it. All these options have their advantages and are safely used to fill the territory of the site. In turn, the creation of a comfortable and practical place to relax in the open air allows not only to optimize the territory, but also gives the opportunity to a person from the everyday bustle.

Varieties of swing

Garden or country swings create an extra comfort on the site. At the same time, such an adaptation will have to taste absolutely everyone, ranging from young children and ending with adults. For children, it is an entertainment that can brighten their leisure. In turn, they bring relaxation and comfort, which is extremely important in modern fast and forever somewhere in a hurrying world.

Similar products can be purchased in the finished form in almost any construction supermarket or order them on the Internet. By making a purchase in this way, it will only remain to establish a design, and then some organizations offer to do it yourself. Such a solution makes it possible to get full-fledged street swings in the shortest possible time, but it requires large material costs, which is not always relevant in contemporary realities.

An alternative to a similar solution is the construction of a swing with their own hands, allowing not only to save a significant part of the material resources, but also the opportunity to choose the form and design of the future building. As a rule, such systems are performed from two types of materials that are inevitably available on the pretending or summer cottage. These funds are wood, metal or combination. In most cases, it is precisely with the help of these materials a gardened swing.

It should be taken into account that modern swings for their own garden can have very diverse forms and sizes, since the main criterion for their creation is its own fantasy. This gives space for experiments and sometimes leads to the formation of completely unprecedented forms. What is the sofa-swing, which are rapidly gaining popularity in our days. In general, the greatest demand in the modern world enjoy the following options for country swings:

traditional;
swing-nest;
swing cocoon.

At the same time, the most popular still remains the traditional option, the creation of which we will look at your own hands further.

Swing do it yourself: stages of work

As mentioned above, most often the swing is made with their own hands using wood or metal, since these materials are the most accessible and inexpensive. In addition, they guarantee the acquisition of an optimal product, which will be different in high strength and comfort. To give these qualities of the future design, it is necessary to take a great responsibility to the development of the project and its subsequent implementation. In general, suspended swings should be performed on the basis of the following scheme, the most fully and in detail describing the entire work procedure. It consists of the following steps:

preparatory work;
drawing up a fundamental plan;
collecting tools;
installation of racks and cross;
creating a seat;
finish build construction.

Building a swing in its own garden on the basis of the above plan makes it possible to significantly save the time of work and get a great result. At the same time, the creation of similar designs with your own hands will be impossible without the availability of skills to work with tools and a clear understanding of the purpose of each process. From here it follows that before starting the construction of the swing, it is necessary to determine their final design and application. Only so you can be confident in the reliability of the future product and its practicality.

Preparatory work

How to make a swing in the garden? Initially, before carrying out the work itself, it is necessary to prepare. You should choose the place where the design will be installed and create optimal conditions for its construction. At the same time, the definition of the construction site plays a huge role, allowing you to obtain additional characteristics of the comfort on the plot. So, the construction in the distance from the recreation area is unlikely to create the best ratio of comfort and practicality on the site. Therefore, the playground for the swing should be located in close proximity to the canopy or even installed directly under it. After determining the place, it is necessary to prepare a plot for work, which requires the implementation of the following actions - cleaning the territory, alignment of the surface and eliminating its defects.

As soon as this stage is over, it is possible to move to the next stage, which is the display of the construction principal plan. It can be based on both the formulation of a detailed visual system of the system and represent an ordinary planogram. In general, you are pretty simple drawings with your own hands. Their main criterion is the choice of the correct aspect ratio and the size of the main parts. Also, this stage include the choice of material for the construction of the structure, which can act as a timber or metal pipes. In our case, the optimal solution will be the use of wood, so we will focus on it.

Wooden swings and their creation requires a widely wide tool list.

This aspect is due to different types of work and a large number of processes to be done. So, for the construction of the swing, we will need the next set of tools:

shovel;
master OK;
bucket;
hacksaw;
roulette;
pencil;
a hammer;
screwdriver;
drill;
a set of keys;
plumb;
level.

As we see, the above list is large enough, which causes the complexity of the upcoming work. At the same time, the collection of all the necessary inventory makes it possible to significantly reduce the overall time of the construction of the object, thanks to which the construction will pass faster and more productive.

Installation of support racks and seats creation

Having finished the preparatory part, you can build a swing from a bar. To do this, you need to dug four pits, which will subsequently installed support racks that ensure the stability of the system. They should be at least four - two on each side. At the same time, the distance between them is determined by the height of the support and the size of the sizes in general will swing from the logs. The same applies to the number of reference elements. So, large and massive structures implying the creation of several places for riding requires additional amplification, which is carried out by mounting the auxiliary reference elements. As a rule, they are installed between the seats to ensure optimal conditions for its movement.

In the process of creating a swing from a bar, wooden racks are poured with concrete in the form of the letter "L", which provides them with additional reliability and stability. In addition, several transverse slats are recorded between them, providing a binder function. As a rule, they are fixed in two or three places on the surface of the racks. At the same time, the flooded supports should stand for several days so that the solution is completely dry and becomes monolithic. It should also be noted that in hot weather it is necessary to periodically water water to prevent the appearance of cracks and chips on it.

While the supports are frozen, you can go to the creation of the seat itself. Wooden swings for giving with their own hands can imply the use of a variety of seats models. Recently, such types such as a cocoon or a nest acquired particular popularity, which allow to obtain a mass of positive emotions from the process of swinging. However, their application is not so universal as the use of a traditional seat that is suitable for everyone, ranging from the smallest and ending with the elderly.

Therefore, our fraud swings will be equipped with a similar kind of landing place. To create it, you can use a variety of remedies available: old pallets or boxes. If there are no such materials at hand, then the seat itself must be made independently. By its structure, it resembles ordinary boxes, in which there is no one side, and a similar model is assembled quite simply - with the help of self-tapping and wooden planks.

Build assembly and processing

When the support parts are completely established, and the seat is ready, you can proceed to the last stage of construction of the swing in the country. It consists in the finish assembly of all elements and the formation of a monolithic structure. It is necessary to start collecting wooden swing from the installation of a longitudinal beam, which falls on the rack with its ends, as a result of which the crossbar is formed. It is on it that the seat itself will be fixed. For greater reliability, the beam itself is fixed with fasteners, providing its immobility and durability.

rope;
chains;
pipes.

The most commonly garden swings made of wood are created on ropes, cables or chains. At the same time, the chains differ good indicators, since they represent the most durable and reliable products. Based on this, the fastening for swing in the garden is best carried out using metal chains. To do this, they must be fixed on the one hand on the surface of the crossbar, and on the other directly on the seat. As a rule, to ensure maximum safety and practicality, the seat is fixed in four places with individual parts of the chain. Each of them is screwed to the wooden base of the seat with metal bolts, and its ends are collected along two and also fixed, but already on the surface of the crossbar.

In this variant, the swing is completely ready and can be used for intended. However, the appearance in this performance leaves much to be desired, so they need to decorate. To solve this problem, you can use a variety of varnishes and paints that will not only make swing more colorful, but will also significantly increase the service life. Thanks to the conduct of such fairly simple manipulations, it will be able to bring joy to all people resting on the summer or garden plot for many years.

Photo Gallery

We bring to your attention the original photo ideas of design of garden swings.

Swing always enjoyed great demand. Yes, it is understandable, because they love to ride babies and adults. In the article, we will tell you how to properly make them in the country, consider various materials (metal, wood), as well as demonstrate photos and video instructions.

Today there are many constructive variations of these structures. We will break them in 3 categories:

Baby. This group includes a swing on the type of chair with suspensions and peculiar boats. The frame is always done in accordance with the security scheme. For very young children, seat belts should be provided.

Family. Most often, they are massive structures by the type of bench with a large back. On such structures, the whole family can immediately fit. They are fixed on the P-shaped frame, using cables or durable chains. If the roof is made above them, then you can swing even during the rain.
Mobile - easily and quickly transferred, and also installed in a convenient place, for example, on the veranda, in a gazebo or house.

Diversity

The hammock type of structures hang on the crossbar, for example, on a tree. This design allows you to soar above the ground. They will like people who are enthusiastic reading books. They withstand weight up to 200 kg.
Suspended is a seating with several ropes fixed on the sides. Today they make them lungs, comfortable and durable. The dimensions and shapes of such structures are different.
Single is all variations that do not need additional crossbars. Such designs can be quickly installed anywhere. They are made from a wide variety of materials.
Swing loungers can accommodate two adults and one child. They can be placed even in the room, because they have only one point on which they are attached. Make them from a special metal alloy. Externally lounge chairs are air, but in fact they are very durable.

To make metal structures, you need to prepare such a set of tools and materials:

Welding machine with electrodes.
Capacity for the kneading solution.
FIRLING / METAL FEATHER.
Ingredients for kneading solutions: water, cement, crushed stone, sand.
Bulgarian for cutting metal elements.
Fasteners: bolts and nuts.
Keys to twist bolts.
Metal pipes.
Shovel.

To start, cut the pipes:

Side racks 2 m long - 2 pcs.
Crossbar Long 1.5-2 m - 1 pc.
For the base of 2 pipes on each side (arbitrary length).

After cutting the pipes, remove the sowing on them. You can do it with a neck for metal / file. Pipes forming the basis of such a structure must be welded at an angle of 45º, as shown in the diagram. After at a right angle to the racks, breed the crossbar.

Drop 2 trenches with a depth of 80 cm and the width corresponding to the tripod resulting in our case. The distance between them should correspond to the width of the crossbar. Supports (tripods) will be inserted into these trenches. Before the support pillars will be laid in the trenches, make a sand pillow for 10-20 cm, sorrow sand. Set tripods and pour them with concrete solution. It needs to be done on the basis of the proportion of 1: 2: 1 - cement - sand - crushed stone. Add water into this mixture. You should have a homogeneous not too liquid mass.

Concrete must stand during the week.

After you can fight the hooks to the crossbar to which the cable / metal beams will be enshrined. Welcome to the beams of metal, secure the seat. You can paint the finished design.

Consider the technological sequence of the manufacture of a wooden structure, on which several children can sit down. Dimensions can be reduced / enlarged if necessary. Pine, spruce or birch wood can be used as the starting material. So you will need:

boards with a cross section of 100 × 25 mm Long 2, 5 m - 15 pcs.;
board cross section 150 × 50 mm 2 m long - 1 pcs.;
self-tapping screw 52 × 3.5 mm - 250 pcs.;
carabiner - 6 pcs.;
welding chain 5 mm thick, equal height;
galvanized screws: 2 pcs. - 12 × 100 mm and 2 pcs. - 12 × 80 mm.

When choosing a screws, pay attention to color. If you choose them into tone wood, they will be unnoticed on the finished design, and it is better to choose a self-effect to give a special effect to contrast.

From the tools you need to stock:

as a carbon;
drill with a set of drills;
roulette;
circular saw;
pencil;
branches;
hacksaw;
hammer.

Following the plan, perform the work accurately - easier. Therefore, before the start of making a swing, prepare its project.

If you find it difficult to decide, then read the drawings and schemes placed at the end of the article. Remember that the design for children and adults is different.

Make the blanks of 1.5 m, make a cut at an angle of 90º. For seating, use a board having a thickness of 20 mm. In this case, the thickness of the backing board can be within 12-13 mm. For the design proposed by us, it is necessary to make a seat on which you will need 17 by a 50 cm long plan and 15 plates of 45 cm wide.

So that the wood does not crack when screwing the screws, drill thin holes in the parts connected items.

If you want to make a more convenient back, then make it curly. To do this, you need to use the boards of the greatest thickness - 150 × 50 mm. You should have 6 blanks. Pencil / marker applies the contour of the shape of the workpiece.

Determine the back of the backrest. Planks should be fixed with the same step. For even their screws, fasten your ends on both sides, and after - in the middle. To swing it was more comfortable, make armrests. For these purposes, the timber will be born of any width. One of his end must be screwed to the back of the back, and the other to the seat.

Then you can attach the chain to the frame. It is best to do this to the bottom of the armrest, at the place of its connection with the seat. The other end of the chain is attached to the top of the framework of the frame on the back. Fix the chain with nuts with washers. Otherwise, the nut can enter the wood than to spoil its integrity. A special element on one side with a ring, and on the other - with a thread, should be fixed on the frame of the seating and on the crossbar.

After, you can connect rings with a chain. Secure the swing benches is better at a-shaped rack. For support, it is important to use strong logs or make a metal frame. It all depends on you only.

Manufacturing support

A-shaped rack or support is quite reliable and able to withstand significant loads. To work, you will need the same set of tools as for the manufacture of seats, if we are talking about a rack of wood.

Make two identical racks having the same size. Ultimately, they will be installed on the distance you need, which depends on the width of the seat. Racks / supports are connected by the crossbar.

Exactly calculate the angle of connecting the vertical parts of the racks. At the top of the pillars should be securely connected. Over time, they should not start to disperse. Reclauded by 1/3 of the height of the support racks. For these purposes, use metal corners and screws. The crossbar must be installed on the racks at one height.

At the top of the rack, one crossbar is usually installed, but if you wish to strengthen the design, you can make two crossbars.

The construction should be installed in the ground. Drop the pits up to 80 cm deep. Make a sand pillow from rubble for 20 cm. Insert the racks and fill them with concrete. To prevent racks, they need to be isolated before filling. This can be impregnated or wrapped with water with waterproofing material, such as rubberoid.

If you make swing for children, then make them safe. Sharp corners eliminate, and wooden elements are stuck.

Simple

You stayed a wooden pallet after the construction of building materials, why not use it as a basis? Agree that it is easy, and not worth the high cost! All you need is a pallet, a solid rope and a tree trunk, for hanging the design. You can make support from strong pillars. About how to implement it, it will be a little later.

Swing can be made of solid pallet, fixed on the sides of four ropes. All, you can ride. If you want more comfort, put the mattress on the pallet and make it a sheet, and put a few pillows on top. Now you can take on reading in the shade of the tree, in addition, you can relax from the midday heat, lie down and even sleep.

If you have 2 pallets at your disposal, then you can create cute designs with a back. To achieve greater aesthetics, you will first clean the parts and squeeze them, and then close and paint (cover moisture-resistant varnish) ready design. Now your non-bright pallets turned into very attractive country swings!

"DOALS" is the most simple idea. On the sides of the junction, it is necessary to fix one more board for more than one board so that the rope is less larching, then drill 4 holes, turn the ropes in them and tie to strong nodes. You can consolidate this design on a tree or P-shaped support.

Another idea - with a rope. To do this, 4 Pazics should be made in the cutter: 2 in the end and 2 at the edges closer to the corners. The board may have a rectangular shape or semicircular. Although the grooves are open, but the rope still does not pop up. The strength of the tension only fixes the position of the rope, which makes the design even more reliable.

Do you have an unsuitable board for skiing in the snow? Then use it instead of seating! Drill holes in it and secure the rope. Now it remains to hang the finished design on a reliable support!

Do you have old tires? Do not hurry to throw them out, because of them you can build beautiful swings for children! For this you need a tire and rope. If you want to create some kind of special form, improve the designs of the tire, then you will need a sharp cutting tool, for example, a construction knife. You can paint the bus that will make it even more fun. To achieve the best results, you can draw a design model on paper or mark the places of cuts on the tire itself. Below are the ideas of implementing tires.

If 2 small round logs are lying in your yard, then align them, clean and tie them with a solid rope, and then tie the sea knot to the support.

We select material

The above mentioned variations of the manufacture of simple swings meant the use of submitted materials. But if you want to create a more refined design, then you can use the appropriate tree of wood and metal. It can be supplemented with a backrest and crossbar placed in front, which will allow to secure operation.

The list of materials required for the manufacture may be approximately:

Larch boards.
Selfless sizes.
Karabina.
Chain for consolidation.
Screws with rings.

To create a design you will need a typical set of tools. It includes a drill with various dimensions of the drill. It can be a useful hacksaw and saw, planer, jigsaw, hammer. For measurements, you will be useful to roulette, square, chalk, or perhaps - pencil, marker.

It is better that the designs are installed in a shady spot, under the roof or wood. If the canopy is not provided, then in the bad weather they must be covered with a protective film.

If you want to create a steady support, then you should definitely go to the soil to a depth of about 80 cm four columns. Subsequently, they will be necessary to concrete, then connect racks and crossbar. If you chose metal pipes as racks, you need to be connected using a welding machine. If you use wooden supports, then before installing them, the material should be treated with an antiseptic preparation. Connect them with bolts and nuts. To make a seat prepare 2 frames that will serve as a back and seat. Attach the phaneer, and then connect the frames at an angle of 120˚.

Now it is necessary to attach special hooks or brackets to the seat, which will allow you to conduct chains through them, cable or rope. In such a state, swing can be swallowed to the crossbar. Please note that the legs of the sitting man must touch the earth with socks. In fact, the country's swing can be the most diverse, here, perhaps, it all depends on the power of the flight of your imagination.

The main thing is that when creating this garden subject you could provide its safety, reliability and durability. Add a bit of creativity into the product: Decorate it, use an unusual object as a seat.

Mount the fastening mechanism

In order to hang the seat to the crossbar, you need to attach special hooks or brackets to it. If you decide to use cables as suspension, then you will need clamps. Through the holes stretch the cable, rope or chain. It is better to use chains having big links. This is due to the fact that they are more durable, weather weather and temperature drops are not afraid. Chains, among other things, perfectly decorated landscape design.

It is better, of course, that the seat was with a back, while the suspension plays a less important role.

The place on which the suspension will be recorded must be particularly fortified. If your seat is wooden, then decorate it with pillows, pull the awning or put the mattress. All these details will only improve your vacation and rest your children.

Swing is an integral part of leisure. You will never regret the strength spent, because your structure will delight the whole country season!

Have you already worked on creating such constructions? What ideas did you manage to implement? Maybe you have difficulty in manufacturing? What helped you cope with them? Write comments on the article, we appreciate your work and experience!

Video

An example of making wooden swings you can see below:

Photo

Schemes

If you decide to make a swing for cottages yourself, then the presented drawings and schemes will help you with this: