We make a circular with your own hands. How to make a table for circular saw. Safety Requirements

When buying a circular saw, the future master does not always imagine the scope of work that he has to do with this equipment. This is one side of the problem. On the other hand, the master understands that he is better to buy a circular machine immediately, but it is very difficult to choose a comfortable table that would meet all the requirements.

The circular table allows you to make a more accurate and smooth sleep.

Thus, the idea is born to make the table for the manual circular saw with their own hands. In this area, these craftsmen have no restrictions.

See also:

Under what work is necessary.

About dump for the motoblock with your own hands.
General requirements for the table for circular saw

The working saw table must comply with several basic requirements:
stiffness support;

stability;

equality.

In addition to these requirements, there are several necessary conditions that must be taken into account when creating a machine under a circular saw.

Safety and reliability fastening saws.

The fence for the saw disk, which is very often unfulfilled.

Free access to the on and off button.

An additional set of functions of fixtures depends on the requirements of the Master itself and its qualifications. This set includes devices that:
help perform smooth longitudinal cut;

the same high-quality transverse cut.

A standard table that can be purchased along with a circular saw is made, as a rule, from stainless steel. The sawing device itself is fastened upside down, approximately in the middle, an incision or a slot is performed for placing a disc itself into it. Its width must match the width used by the saw disks. It is impossible to allow this gap to be too wide. In this case, the chips and the other worker will often clog the device, deriving it out.

As for the technical parameters of the saw, which will be used for machine cutting, its engine power can be greater than the ordinary hand saw. But still not exceed 1200 W, experts consider such a risk unjustified. After all, the more powerful saw, the more durable and reliable table needed.

Industrial machines are manufactured as already mentioned, exclusively of metal, but their support is very often poured with cement for more reliable fastening of the device.

Back to the category

Required material and assembly of the table for manual circular saw

For the manufacture of the table, you can take the following materials:

phaneur 20-50 mm thick;

plexiglas;

plates of fibercristolite.

Choosing saws in the store, the buyer often draws attention to the depth of immersion of this instrument, which means the maximum thickness of the material being processed. It is necessary to assume that the use of a manual saw is not for the purpose will select approximately 1 cm of sawing thickness.

The table parameters are largely dependent on the treated surfaces.

If it is assumed that the products will be bulky, for example, more than 2.5 m long, then the table will have to strengthen additional legs.

The circular table has several features in its assembly. The workpiece for the table cover should be described by a separate item.

So, for the table tops are made of legs from the same plywood, but more thickness. To secure it, retains along the table or cross. This will allow the table to be tougher. The stability will affect the correctly selected leg length, the installation location.

The table can have different sizes, these parameters master determines independently. For example:

cover 70x80 cm;

height 110 cm.

Back to the category

Table lid: How much useful on it can be

For the saw itself, depending on the thickness of the table top, it is done with a depth of about 1 cm. The sleeve is made for attaching the desktop of the device itself around the perimeter. In order to make it, using a ruler, a simple pencil and a manual saw itself, mark the place where the device will be located.

There are several options like fastening saws to the table. It all depends on what purpose is delivered. If a person wants the saw freely dismantled if necessary, the mount should allow this to do, but it is reliable.

For this, around the marked perimeter of the working surface of the saw, limit bars with grooves, without forming a closed frame. Thus, a manual saw is fixed. But this installation is applicable to small volumes of work and small speeds of disc revolutions.

More reliable fastening looks likewise, but with such a mount, the bars have a smaller size: they are not 4, and 6 or 8, each is fixed near the particular area of \u200b\u200bthe bed, and if necessary, the master will have to unscrew the bolts near each such bar. Some fasten the circular without wooden bars, screwing it straight to the table, making holes in the bed.

Turning the table cover, you can see a slot with a disc head protruding from it. When installing, the disk platform fixation feature is used.

You can make a slot on the sawing table for a removable deflocked knife, which with the help of clamp will be attached next to the saw from the bottom.

Back to the category

Guides for longitudinal and transverse spins

The table must have guides, for their manufacture use aluminum construction P-shaped rails. At the open edge, they cling to the table. Subsequently, the auxiliary fastening details will be moved to perform more accurate saws.

The first must be built into the guide, going along the saw. Reiki for a parallel guide will go along the edges of the table, perpendicular to the pile itself. The guides themselves are also made of plywood.

Back to the category

How to perform transverse cuts?

To perform transverse saws, the bar is most often used, which looks like a small table. It will be turned over, has 2 parallel bases and a slit through which the saw disk can pass. If all the angles were respected, the cut will be strictly perpendicular.

The solution for the transverse direction of sawing can one more interesting option. On Phaneru (slightly large than the table), bars are attached from the bottom. They should be located clearly on the width of the table. With the top of the board, 2 parallel plates are fastened, which are above the saw blade and have slots for its passage. The result is the same, but such a solution is more easily implemented.

In addition, the table lid can be equipped with rules on both guides.

Circular saw is an important and need for many people tool, allowing you to independently engage in numerous types of work on the house. It has a fairly high cost, so many people think about making it on their own. To do this, you need to prepare a workbench or the optimal table that replaces this tool, and also need to have skills to work with the metal. During the process, you should be ashabled and careful to not harm yourself, as well as get the perfect result of the work.

The circular is made with their own hands using the following components:

profile pipe rectangular shape;
corners formed from steel;
engine.

How to make a hand saw from the Bulgarian?

A homemade circular was considered quite popular from the disk saw with their own hands. Most often for this work is used by Bulgarian. To do this, only some changes are made with a ready-made tool that is equipped with a special sliding focus, and an axial handle is installed.

All work on the independent creation of a circulating saw from a grinder lies in the following steps:

It is created on the tool sliding emphasis, represented by two corners of small dimensions made of metal. They are installed from two sides of the main working body of the tool represented by a disk with different teeth used instead of a standard abrasive circle. At the same time, on each side, a gap of 4 mm is left.
In order for the installed corners during the use of the already finished saws, they did not cling to the detail exposed to processing, they should be rejected below. In front and rear, they are connected by special cross-links, for which standard fasteners are used - bolts and nuts.
A special clamp is attached to the Bulgarian itself, made of tape formed from metal. At the same time, its spiral screed must be at the bottom of the tool. A strip of tin is fixed to this clamp, in advance folded twice, and it is allowed to replace with galvanized. On this element, there must be a special hole intended for fixing the rear bolt of the sliding stop.
Create identical gaps between the focus of the future circulation saw and its working body are created.
In the gearbox housing, which is an important element of the grinder, is created from 2 to 4 holes equipped with threads. They are designed to use small bolts. For this work, the reducer is originally disassembled to determine exactly where it is possible to create holes in the drill holes in its housing. It is with their help that an axial handle is recorded, which can be purchased in the finished form or done on their own.
If it is supposed to perform an axial handle on your own, then a metal tube is used for this, and a metal bar can also be applied, which has an unusual curve form. In the created handle, as well as in the gearbox housing, holes are formed, after which the fixation itself is implemented.
Next, an adjusting rod is created, for which a small segment from the steel rod is usually used, and its thickness is usually 5 mm. One end of this segment is bent, resulting in a loop. A hole for the front bolt of stop is created. On the front of the stop, the washers are selected, which will allow you to get uniform and optimal clearance in width. On the other side of the rod, a thread is formed, which is included in the hole existing on the saw handle. To do this, the nut makes the nut in advance, and as soon as the assembly is completed, the second nut begins. Using these nuts, which are easily tightened or released, the optimal and desired depth of propyl is ensured.

Thus, the process of creating a manual circular slab is considered fairly simple. Here you do not need to use expensive tools and materials, as well as all work is easily implemented on your own.

How to make a desktop circulating plate?

You can even make a table for circular with your own hands with drawings that are formed in advance, as well as high-quality and correct. With their help, you can get a design with high quality, safety and performance efficiency.

The full circular saw, formed on its own, is represented by a serious, complex and unusual design, which is created only when preparing all its elements, the study of drawings and preparation of materials and tools.

It is important to determine whether the circular is stationary or desktop will be, and the choice depends on how the tool will often be applied, as well as the scale of work it is assumed to be implemented with it.

Standard Circular Saw Construction

"True" stationary circular

The table for circular is your own hands, the drawings of which are available in free access, it is created easily and quickly, if it's good to know its design. If you separately form and prepare all the components, then as a result, they are just secure and firmly connected to each other, providing the optimal design.

The main elements of this equipment refers:

Table. It is usually covered with a sheet created from galvanized steel or tin. It is not allowed to apply plastic or wood for these purposes, since these materials will not be able to withstand the essential impact of other materials, so they will argue, as a result of which deformations, bends and holes will be obtained.
Cross-links. They are created for the table, and usually the steel corner is used for these purposes, the thickness of which is approximately 7 cm. Communication data is equipped with a shelf attached from the outside in a horizontal position. In this case, the ease of formation of the side limiter is ensured.
The working organ of the circulation saw. It is represented by a toothed disk, which protrudes beyond the limits of the table, as it provides a good process of feeding different elements.
Motor equipment that must be sufficiently powerful. Its selection depends on the diameter of the saw. If it is supposed to work with sawn timber, the thickness of which exceeds 15 cm, then a very powerful motor is selected, therefore the process of creating a circular will be quite complicated because it is difficult to find this element in free access.
Side focus. It is made adjustable, and it is used to create a smooth piece of angle of steel to create it, the thickness of which is approximately 7 cm. This stop in length should be larger than the table length of approximately 35 cm. One vertical shelf on each side is cut, so it turns out to be equal to the table length . Tails, which are flat, bend down. In the lower rods, the holes for the thread are formed. The emphasis is attached to the table with bolts, and it is exposed exactly on the template.
Shaft. It is an important element of the equipment, and it is advisable to purchase it in the finished form so that it possesses high quality and reliability. Usually the finished element has a special landing place designed for a disk of a future saw.
Bearings. They can be different, but the most optimal choice is considered self-aligning elements that are balls. They are equipped with a double side of special balls. Inside the clip in the context is curvilinear. If you use cheap and low-quality bearings in the homemade circular, then they will not last too long. The troughs are equipped with covers that prevent falling into the bearing of sawdust.
Transmission of saws. It is usually selected by a clinorem design, since if you choose a gear, it is considered to be sufficiently dangerous for use by the lover. This is due to the fact that if the lumber is used, which has previously been used for other purposes, then it can get a nail or other fastening element, which when entering transmission can contribute to the fact that the engine disk simply splits.
Ratio. It is selected depending on the engine parameters, namely from its revolutions and on the speed of the disk rotation.
Engine. It is best to choose an asynchronous engine that is single-phase. Typically, standard washing machines are equipped with such elements. They are ideal for homemade circulating saw. It is not desirable to use collector engines that are usually installed in different electrical devices, as they give extremely significant revs, and can not work for too long, which is considered important for the circular.
The three-phase motor is used often, however it is complemented by a start-up and working capacitor that are equipped with reinforcement. They have a substantial cost, and they must be either oil and paper, or just paper.
The engine start circuit, which can be used for a triangle or star, and it should not need additional refinement.

Thus, the process of creating on its own circulation saws is considered quite difficult, however, if you know, from which basic elements equipment consists, as well as select high-quality elements, securely and safely connecting with each other, the work will be correctly performed independently.

They read this article on the blog - be careful in experiments and work with sharp tools. Write reviews and share tips on working with saws and circular plates that have made themselves.

The circular machine is the tool without which no home master can do. This equipment is especially relevant for a country house or cottage. But it is not always convenient to work with a manual machine, and the factory machines are quite expensive.

The output from the current situation can be the manufacture of this device with your own hands. The basis of this machine may not only be a manual circular saw, but even an electric drill or Bulgarian.

Make a bed for a circular machine with your own hands very simple. For manufacture, the most ordinary pilomber And quite a bit of time.

Before thinking through the design of the upcoming machine, you need to calculate the load that it will be exposed. The main thing in the bed is reliability and stability. For powerful production saws, the base is a welded reinforced metallic design. But for use with your own hands, such an aggregate is not needed.

If you just decided to make your woodworking machine, then you need take into account the main parameters equipment. Since the saws can be different, naturally can be the design of the bed.

First you need determine the power tool. As a rule, equipment is chosen for domestic use, where the power parameters do not exceed 850 watts. But, for example, in the construction of a cottage or country house, it is often necessary to cut a very large amount of wood.

That is, and the power of the circular is required more. But experienced masters do not advise you to buy saws, where this figure is more than 1250 watts. Installing this equipment in the home workshop is absolutely not justified. And the work on it will only increase the cost of electricity.

The larger the machine performance, the stable for it it is necessary. For professional circulars, as a rule, establish the basis, steel profile. Sometimes these birds are even concreted into the floor. Since the vibration of the device can lead to a danger to life.

Technical Features of Circular Machines

Depth of the alleged cut. This parameter depends the thickness of the material to be processed on your machine. This indicator in semi-professional and professional machines ranges in the range of 5-8 cm. For cutting boards and thick plywood, this is quite enough.

But it will be inconvenient to work with the brothers on this machine. In addition, it is necessary to consider that this characteristic of the homemade saw is reduced. The depth of the cut will be less than approximately 1 cm. But this can be avoided if you provide in the table of the table the ability to omit or lift the disk.

In the manufacture of the tool you need take into account the frequency of its rotation. If the circular is required for the workpiece of the building material, then this indicator may be less. If a clean and even cut is required, the rotational frequency is needed quite high. It is necessary, for example, for the manufacture of furniture.

But in this case there are certain nuances. For cutting plastic materials, this saw is not suitable. Due to the very large turns of the tool the disc is heatedAnd plastic begins to melt.

Therefore, it is better to choose a device where the speed of rotation is not more than 4500 rpm, in this case the bed for circular saw can be make from wood. The vibration of this machine is low and the additional strengthening of the table is not required.

Well, at the end that it is necessary to foresee, this is the location of the buttons and other controls on your machine. When assembling saws, do not forget that access the control panel must be safe. Moreover, this is the rule in the case when the open part of the saw is located at the bottom of the table top.

In this design, the panel with switches is best postpone from the outside of the machine Either make a rising countertop. This design is convenient for maintenance of the device. Then, when you took into account all the nuances and trifles, you can start directly assembling the table.

Making a circular saw with your own hands

The easiest option of the beds for the circular is a design made from boards and thick plywood. And directly the tool is attached to the bottom of the stationary countertop. For a saw in the table lid, a special slot is made.

Dimensions for the table can be changed as it will be convenient for it to work on it. For example, the middle table is described, the height of which is 110-120 cm. But there is a lot of depends on the growth of a person working with equipment. Also, at your request, you can change the length of the tabletop.

If it is supposed to work with boards, in which the length is more than 2.6 m, then the lid on the bed will need more. In this case, it is necessary to make changes directly to the design and additionally. add a few supports (legs). Otherwise, the table will create strong vibrations.

For countertops usually used plywoodwhich has a thickness of at least 5 cm. But you can also choose a plexiglass or stove of fiberglass. But the use of chipboard professionals are not recommended, this material is not reliable enough.

Tools and materials for assembly

For circular saw, you must provide for the guides. They help to cut wood much more accurately. This design weld from steel corner And fixed to the lid of clamps.

Fasten the same stationary guides is undesirable, since later you will not be able to change their position.

For the construction of the table you will be needed such materials:

iron sheet;
plywood sheet;
bar size 50 × 50 mm;
50 × 100 mm size board;
steel corner for guides;
two clamps;
manual circular saw.

You also need to pre-cook all the tools that will be necessary for the background assembly:

Sculpture, electric drill.
Hacksaw or electric jigsaw.
Measurement tools (roulette, square, ruler).
Manual milling cutter or milling machine.

When everything is prepared, you can begin the assembly of the table itself. Sometimes masters collect countertops from unnecessary dining or kitchen tables. But this design is unlikely to serve for a long time. Therefore, much more intelligently all elements of the design make with your own hands. In this case, you can also take into account your personal needs.

Making countertops for circular machine

Assembly of the table start from the manufacture of table tops. The plywood sheet is placed so that two edges of the lids are in size with the edges of the iron sheet. Phaneur is cut with a hacksaw or an electric bike.

The edge of the spike can be treated with a cutter, but this operation is optional. Since in the face the main parameter is reliability, and not an attractive view. The countertop rubbing "Naturally" sandpaper.

From the bottom of the countertops noted circular circle. For which at first it is necessary to measure the size of the soles of the aggregate. It is easiest to do this if you unscrew the disk from the device and simply bore the desired part of the saw. These measurements are required to determine the seating.

With the help of a manual cutter, the bars are chosen to a depth of approximately 0.9-1.1 cm. If you do not have a cutter, then this work can be done using a chisel, but this will take it much more.

Then, when the seat is done, try the saw, and if necessary, adjust the recess. Follow the spaces of the slot for the circle and fixing fasteners. If you need a circle to raise and lowered, then it is necessary install pendulum mechanism For countertops.

In this case, the slot must be made in the form of a truncated pyramid. In this case, the hypothetical peak of the pyramid will be directed down. Directly frame for the lifting mechanism is best make from steel cornerswho are welded with each other.

Making frame frame

Markup for fixing transverse speakers and longitudinal, which perform the function of rigidity, it is best to install from the wrong side of the table top. Directly the planks are made from the bar. You will be needed:

Two transverse parts, a long equal tabletop width minus 7-9 cm on each side.
Two longitudinal ribs, the size of equal length of the lid minus 7-9 cm on each side.

Then need make nest for screws. The rails need to be fixed on the lid so that the countertop goes beyond the edges of the frame by 7-9 cm. Fasteners should be as reliable as possible and durable.

The first mount must be set by approximately 40-50 mm from the edge of the rail. Distance between self-sustaining approximately 23-25 \u200b\u200bcm. All items you need to drill through. Saws is attached from the side of the lid so that its hat is completely accumulated in the tree.

Initially fasten the transverse ribs. So that the table lid was as strong as possible, the edges of the rails are predefined wash in joinery glue. The design is fixed by clamps, and without removing them, screws the screws.

The countertop is allowed to dry. After, the longitudinal rails are installed in the same way. Then parts of the frame are tightened with each other by installing two fasteners on each side. Now clamps can be removed.

Fastening legs (supports)

The stands of the table are made of bar. The height of the support is selected individually. In practice, it is more convenient to work at the machine when the countertop located at the hinder level. Before mounting each support, you need to compatinate it so that the leg came down from below. So, the base of the support should be slightly larger, unlike the top area.

It is best to fix legs with steel corners. They need to squeeze a bit so that the base of the machine is in the "strut." It gives the table additional resistance. As a fastener, bolts with washers are used, they are attached to the hats outside. Otherwise, during work, you can be injured about the protruding pieces of fasteners.

The whole design will be stable if additional supports are pulled by diagonal slats. They are fixed in pairs from each side of the machine.

Surface cover polished and treated with varnish Or used to cover a steel sheet, which is attached to the screws. At the very end, to the prepared place, the instrument is fixed directly.

On the cover of the table can be additionally make markingShe will help smoothly and properly saw wood. The circular saw control panel is located on the outer side of the machine. As a rule, it is fixed on one of the legs of the table. That's all, circular saw with their own hands ready.

Circular saw with your own hands is going easy. Homemade devices are often found in workshops who have the necessary skills to work with tools.

All actions during manufacture must be carried out carefully, observing safety regulations.

The drawings of the device of the device will make the process of assembling circular saw with their own hands more understandable.

Order assembly

Homemade circular saw with their own hands can easily be collected if there is an unnecessary grinder in the home workshop.

For the work of full assembly of the device, you need to prepare the following materials and tools:

bulgarian;
aluminum corner;
nuts;
metal rod or pipe;
metal canvas;
emphasis for sliding (you need to collect);
an axial handle (need to do).

First of all, the stop with the necessary holes is constructed. It is constructed using short parts of a metal corner. Crimping the angle will be located on both sides of the toothed disk.

For them, on the sides, it is necessary to make removing depth from 0.2 to 0.5 cm. To the lower edges of the corners do not come into contact with the cutting element, they should be smoothed.

Details are fastened from behind and in front of cross ligaments using nuts and bolts.

The scope of the assembly is not complicated. A metallic clamp, the tie of which is produced from the bottom of the device.

Then they prepare a hole through which the product is fixed with a clamp for the rear mount, which fixes the stop for the subsequent slip.

In the gearbox of the device drill holes with an applied thread, in which small parts will be mounted.

At the beginning of work, the gearbox is disassembled to determine the right place where the recesses will be performed.

Recesses are required for subsequent mounting of the axial handle. If a handle located on the side of the ordinary grinder is used, then the hole will be performed quite difficult.

The next stage is the manufacture of the handle. The item can be built using a rod curved upward or tube made of metal. Her ends will continue to be attached to the reducer.

If the handle is made in the form of a horny, then its long-range end should be flattened and do the recess under the axis. In the removal, located in the gearbox, insert the part sent forward. The edges of the details are pressed.

Using the lining of the washers under the front of the stop, equal to the gap parameters along the duration of the circular saw.

If a rod is used 0.6 cm, then thin washers will be needed. Threads are applied on the back of the rod.

Then the item is placed in the recess on the handle. Now the device is ready to use.

During the operation of the circular saw, it is necessary to comply with the safety regulations, especially can not drink alcoholic beverages, as their use leads to a violation of coordination.

Building table saw

Circular saw assembly with your own hands at home is not a very difficult job, you only need to prepare all the necessary parts and tools, choose the design and accurately follow the drawings and instructions.

Desktop circular saw easily collected from the usual. The finished device will have a compact size.

To accomplish this work, it is necessary to collect from a thin tube or a pntach of 18 - 20 mm made from metal, the box to which the lever joins.

The part of the construction located below should be bent in the direction of the cut. To the table, this element is fixed with self-draws.

The stand for the apparatus should be stable. Swing saw during operation can be very dangerous because any careless movement can lead to loss of fingers or hands.

It is best to make your table from the metal, consolidating his supports to the floor.

On the crossbar you need to put the lever made from the tube in the form of the letter "T". The lever must freely scroll.

The part is cut in the diameter into several sections. After completing the installation of the design, all elements are connected by using clamps.

The homemade mini circular saw with their own hands is attracted and fixed by clamps to the vertical extreme part.

The collected circular saw can be used in the home workshop as a cutting tool. Before starting work in the Bulgarian insert the cutting circle.

To handle thick boards, you need to use a full-fledged device. Carriage performing the elements. It is collected from several brusons that are attached to the base and performing a guide function.

Understanding how to assemble the device, you need to choose the suitable materials and tools suitable for work. At a minimum, you will need working Bulgarian and various consumables.

But to properly assemble the device, special skills are needed. If there is no needed skill, it is better to get a circular electrooper, in the correct, reliable and safe operation of which you can be absolutely sure.

The described method allows you to assemble a small circular saw, which can be used in a home workshop or your own shed.

How to assemble stationary apparatus?

Learning how to make a circular saw, proceed to the assembly of the device. Stationary saw from a mini tool differs only by the sizes of statins.

Statin should have a base of sufficient width without curvature, having a cutout for a saw. More often, the base is done using plexiglas, phaneur, chipboard and ordinary sheet metal.

The closing surface parameters are determined by considering the pressure rendered on statin. Circular saw power wire is also attached to the base.

The statistical cover should be freely removed, as access to the machine may be required at any time.

The table for the design will need to do it yourself.

It is covered with tin or steel sheet, as the tree, passing during work on plastics and wood, gradually forms furrows on the coating. Because of the wells and deepends to make high-quality sleep will be very difficult.

If the Planck is planned sliding, then it is necessary that the surface of the table has absolutely parallel opposite edges.

For unhindered slip on the edges without changing the desired angle, salazzas made using an aluminum corner are manufactured.

The cutting disc on the surface of the table should be not more than a third of its diameter, otherwise the tool will be dangerous for life.

But the minimum protrusion of the cutting element can bring serious injury during improper use.

Before starting to build a circular saw, you should compare the power of the existing electric motor with the necessary one. Details of a thickness of more than 150 mm to cut up the homemade apparatus will be quite difficult.

Emphasis, which can be adjusted in the process of work, make 7-8 cm from the metal angle fragment. It should be a little table top.

Then the focus is on the surface of the table, which is fixed with bolts. The focus is exposed to special measurements, which is predetermined between the working part of the device and them.

Such a useful thing as a working engine from an automatic washing machine should not be crazy in the garage.

Any respectful self-relocated hands will begin at the sight of such a promising detail.

In this article we will tell, as on the basis of such an engine, make a very good light and compact circular, on which the fiftieth board or even the 10x10 bar can be dissolved without any problems.

Attention! Assembling circular saw with your own hands and its further use may be dangerous! Therefore, do not care if you are not sure about your skills and do not follow the security rules! This article is not a call to action. And remember all responsibility for what you do is only on you!

How to connect the motor?

Connecting the engine is the most important stage of the work, if you fail to connect the engine from the washing machine correctly, then the circular will not do with your own hands. All complexity is not even in connection, but to achieve a stable adjustment of the rotor of the motor, without this, the circular will not work normally - the disk will tear the sawn timber.

On the engine from the washing machine, the machine manufacturer sets the so-called Danger or speed adjustment sensor. But the problem is that the operation of this sensor controls the electronic module of the washing machine, you will not deliver such a module to the circular, so you will have to think about the device that will control the engine turnover. In detail about how it is described in the article of the same name.

Moving parts

Successfully connecting the engine from the automatic washing machine with your own hands, and checking how it is gaining and slows down, you can start doing our circular. The scheme below shows a simplified drawing of the self-made circular saw made using the engine from the washing machine.

The scheme can still be easier, being from the bearing assembly. For household circulars, this is permissible.

While we will only be interested in the moving elements of the circular, to which the main load will have, namely:

shaft of the disk saw;
washing machine shaft machine machine;
drive belt;
machine pulley Machine machine machine;
pulley shaft disk saw.

The drive mechanism should work as follows. The engine from the washing machine leads to a motion shaft with a small pulley pressed on it. On a small pulley, a drive belt is dressed, which transmits turns to a large pulley, dressed on the shaft, driven by a disk saw. It seems at first glance everything is simple, but when you do a circular, it pops up a lot of subtle difficulties that you have to resolve.

Small pulley must be able to dilute with their own hands, making 3-4 transverse grooves on it, in order for the belt clinging for them and did not slip.
The drive belt is not necessary to take an automatic from the washing machine, you can take a similar item from any other technique, if only the belt was durable and had tobsed.
On the big pulley will have to start the edge with your own hands a slightly larger diameter, so that a peculiar protrusion is formed, which will not give the drive belt to jump during operation. On a large pulley, it is not necessary to drag the bodied, the clutch with the belt will be normal and without it.
The shaft on which the disk saw will be held, as well as the nut and the washer should be reliable to, firstly, on high speed, the disk saw was not deformed, and secondly, that the disk saw did not jump off and caused harm to a person working with a circular person . It is better to take the finished shaft, washers and a nut from the staffing factory circular.

The described mechanism is designed for a three-way disk. Many skeptics are located, which say that the engine from the washing machine does not pull such a disk, and that he will stop at a certain point during operation, and the saw will be stuck in the board. Such skeptics our specialists answer the following.

First, you need to be able to work with a circular and not push on a rotating saw anything.
Secondly, this circular will be purely household, it is designed for short-term work with a small amount of lumber. If you want to make a circular for business, then purchase special components, such an equipment is not manufactured from undergraduate parts.
Thirdly, the practice shows that quite a lot of craftsmen use such self-made equipment and very satisfied. At least, feedback from them, mostly positive.

In the future, do not overload your homemade circular work, and most importantly do not work the engine for a long time without load.

Stanina and Rama

Collect the parts for the moving parts of the circular, we can only make a reliable frame and a bed for our circular. In principle, for the foundation of household circular, you can take the most ordinary rebunny material, for example a piece of thick flat slate. Cut from it a rectangle and cut through the hole under the disk saw nothing costs. But we are supporters of capital structures, so pretended for the cirklasp bedroom to take a metal sheet with a thickness of 3 mm, and for a frame of 30 mm, a metal corner.

In the figure, it is clearly clearly visible, from which elements a frame of homemade circular is consisting. In this case, it is also welded with your own hands, only as a support is used not a static metal corner, but special homemade racks. The rack is made of two metal pipes of different diameters, which are inserted into each other, thus, the cirrcular string can be adjusted in height.

Experts insist on a welded frame structure for a circular, as the vibration is badly affected by static mounts created by bolts. Although if you do not have a welding, in the extreme case, you can make a frame from the corners by crossing them between themselves bolts and nuts. The bed to the frame is also better to privar.

So, make a circular from the wash engine with your own hands it is possible if you have experience making different homemade homemade. Try it yourself and, perhaps, you will accumulate some experience that subsequently share with our readers. Good luck!