What can be made from the old boiler: smoking, mangal, receiver. Solar water heater for giving from the old refrigerator What can be made from the old water heater

If you have an old boiler, do not hurry to throw it away. From it you can make a lot of interesting and useful things. In this case, we will look at how you can make an excellent grill from a boiler.

Materials and tools for homemade:
- Old boiler;
- Bulgarian with grinding and cutting discs;
- pliers, screwdrivers, nippers and other classic masters tools;
- corner or other suitable material for creating legs;
- drill with drills;
- welding;
- heat-resistant paint (the author has black);
- loop with a lock for pondered;
- bolts, nuts, washers and other fasteners;
- Grill round shape.

In general, the drill may not need, just the author decided to make everything collapsible, connecting the structure with bolts with nuts. You can, in principle, all this is just welded if all the details are made of steel.

Grill manufacturing process:

Step one. Preparing boiler
First of all, you need to take a boiler and delete everything too much. As a rule, boilers on top are separated by thermal insulation, so that they have long stored water warm. This isolation needs to be carefully considered. Perhaps first it will need to be cut off with a grinder or a sharp knife, depending on which the plating is made. Well, then the Bulgarian is taken with the enroll break and the entire insulating material is removed using it.
It is important to remember that the remnants of isolation when using the grill will begin to penetrate.

Step second. Cut the boiler
Now the boiler must be cut. Here you will need Bulgarian again. The author decided to choose the part of the tank, where the bracket is located, with which the tank is attached to the wall. In the future, this bracket will be needed to build a wooden plate. In addition, the author also cut the opening on the workpiece to install the lattice.

Step Three. Production of legs
The legs are made very simple, there will be a steel corner, or the elements of metal racks, which author used. For fastening, it was decided to use bolts. But for ease of procedure, everything can be combined with welding. As for the length, it was decided to make the legs with a length of 75 cm for ease of cooking.

Step fourth. Finish legs
Using the legs as fastening the legs bolts with nuts, the author killed two hares as one blow. Due to the inside the screws now you can install grill grille.

Each leg is fastened with two bolts with nuts, so it will be necessary to drill holes in the tank. It is very important that the upper holes are on the same level, since the grille will be located here. It is best to mark a couple of points from the top and then spend around the line. The legs should also be located at the same distance from each other.

After the assembly it turned out that the grill is not very reliable. To make the legs tougher, the author added to the lower part of the cross.

Pitch fifth. Infused for grill
For the effective work of the grill, the author decided to equip him with a confusion. To do this, in the bottom of the tank you need to cut the window. The resulting plate should not be thrown out, the door is done from it. The door must be fixed on the loop, and also to fade. It is important to take care of the handle, it should not actively carry out heat, as it will be very hot when using the grill. The author made it from the bolt and several nuts.

To secure the lower grille, you will need two steel rods. The author simply welds at the desired level by circumcalling unnecessary. If you have no time to spend the rods, you can use thread rods and secure and fix with nuts with washers.

Step six. Fastening for a wooden plate
The wooden stove is a very convenient addition to the grill, though the grill itself should be well fixed. Here you can put plates with cooked food and so on. For a wooden plate, the author drills in the bracket of the hole of the hole, and then inserts the rods with carvings. Subsequently, wooden bars will be attached to these strains and put into nuts.

Step seventh. Painting
At this stage, the author paints the item made from a boiler. Previously, you need to contemplate the whole rust and make a pretty ground surface. The paint can be needed heat-resistant, since the container is strongly heated.

Step eighth. Assembly
After painting, the whole design is going again. Using a level, it is desirable to measure the slope of the grill and adjust the legs.

Also, the author is fixed by the hinge and the valve pondered. For such purposes, rivets were used. You can also use nuts with nuts.

Step ninth. Production and installation of internal grid
Coals will be loaded onto the inner grille, and the air will come from below, which will lead to good coal burning. For the manufacture of the lattice, the author decided to use a steel plate in which he simply twisted holes. The found plate had already had a couple of squares of square holes. It is important that the plate is thick, since the coals for burning form a high temperature.
Then it will only remain to put the plate on the rods woven into the lower part.

Step tenth. Collect wooden stove
The wooden plate is going very simple. Here we need wooden bars that need to be cut in size. Further, two holes are drilled in them through which the rods with carvings will be held. The author has a hole in the form of the letter "V".

Well, then this entire sandwich is going and well tightened with nuts. It is important to stock up good large washers here, since a considerable effort is needed for tightening. The washers are put on both sides. At the assembly of the author left 10 nuts. Two here act as a support, and another two on the other hand pressed wood. The remaining nuts are needed for fixing the rods themselves. Tighten everything you need a good, using wrench.

As a result, a wooden slab can be cooled to polish well, and it would be good for protection to paint it with protective varnish, paint and so on.

In conclusion, it should be mentioned that the grill should be reliably fixed, otherwise, if you put something heavy on a wooden slab, the whole grill can turn over. It can be screwed to the floor or to a large heavy board.

Step 11. Getting Tests
That's all. The grill is assembled, now it can be experienced. According to the author, the project was successful and worth the forces spent.

2017-01-05 Evgeny Fomenko

There are many options for what can be made from the old boiler:

Burzhuyka Corps made of old boiler

We are placed chalk space for two rectangular holes, for the door and for the furnace and cut them out. We have a device so that the hole from the tan is above. We weld the mesh from the reinforcement, the holes from the pipes are brewing.

On the doors we screw canopies, small metal strips so that they do not fail and a small latch. Blowim from the bottom corner as a support. For drawing on the site of the hole for the Tan, we cut the circle on the diameter of the ventilation pipe.

Hoody man from a drowned water heater. Give the tank, cut off the tube input and output of water and the upper part. Eliminate the leak, brewing it. We clean the container and paint enamel. At the place where the pipes were located, weld the crane.

Dusting bucket. From the housing you can make a beautiful urn. We cut off a rectangular piece of casing and we are replenished evenly cuts, centimeters of 20 and bend them. Twist in the pipe and fasten with rivets.

Vegetable growing place. By cutting along the tank, we get two comfortable flower beds, welding supports to them and filling the earth.

Video "How to make a burgundy from an old boiler":

Solar water heater (collector) - an indispensable assistant in the household. The collector of the desired size and design is able to provide hot water from several people from several people, while saving hundreds of - thousands of rubles, which are spent on electricity and other types of energy resources.

If there are no electricity and gas on your dacha, and water heating is a certain difficulty, I propose to make a solar water heater for a shower and washing dishes from materials that often can be found on the landfill.

To begin with, it is necessary to find a faulty refrigerator, namely it will be required by its coil, which is fixed on the rear wall.

After the serpent is dismantled, it must be rinsed with a stream of water to get rid of the old freon.

We reserve the rails that we need in the future for the manufacture of a frame.

There was an old rubber rug, which often underwent under the door.

Glass, so it is not necessary to buy. It can be dismantled from the old window, which is usually thrown into the trash, when replacing plastic windows.

Since our rubber mat turned out to be Velic, it was decided to cut it into the size of the future carcass.

From the rails, you pick up the framework, so that the coil is freely placed between the rails.

We try the coil and rubber rug to the frame. We celebrate the place of fastening the bottom rack of the frame and the locations of the cuts to exit the tubes.

We establish the lower rack of the frame, we climb foil between the rubber rug and the frame.

On the reverse side of the frame, you feed the rail to give stiffness of the structure.

Scotch tape carefully glue all the cracks between the frame and the foil. This is necessary so that more cool outer air does not fall inside the collector.

For the flow of water to the coil, PVC tube was purchased.

Sealing the connections of tubes and a serpentine, the ball is ensured by scotch.

For mounting the coil used clamps that were removed from the refrigerator. The attachment of the clamps was also provided with scotch. But for reliability I recommend consuming with screws.

We cover our design with glass and sample on the perimeter of scotch.

Homemade solar collector is ready. For the best heating, the sun rays must fall on the surface of the collector at a right angle. Therefore, the fastening of the design elements is completed.

So that the glass from the heat did not go, below must be screwed by a couple of screws that will be stopped.

Now it remains to attach the hot water accumulation tank.
Circulation occurs only as a result of natural convection. When heating water in the collector expands, it becomes less dense, rises up the collector and enters the top of the tank battery through the pipe. As a result, cooler water at the bottom of the tank is supplanted and flows on another pipe into the lower part of the collector. This water in turn heats up and rises into the tank.

1 - hot water; 2 - pressure discharge valve; 3 - Drain of hot water; 4 - shut-off valve; 5 - fuel valve; 6 - cold water; 7 - Cold water supply; 8 - drain valve.

While the sun shines, the water will constantly circulate on this contour, increasingly heating. Due to the fact that the tank is raised above the collector, the effect of tilting the circulation as a result of the night cooling of the coolant in the collector is not coming down to NO, since the cold water simply accumulates at the bottom point of the system (at the bottom of the collector), while warm water remains in the tank.

Such a simple design of the solar collector, can heat the water on a sunny day, up to 70 degrees.

In addition, for the dacha you can quickly make your own fan from the CD \u003e\u003e

Are you going to send an old accumulative water heater to the landfill? Do not hurry. He will still serve you a useful service. How to remake the old boiler with your own hands, we will tell below.

Alteration options are suitable for cumulative models, because the basis is the tank.

Useful products from water heating tank

In the skillful hands, any thing that has served the term turns into a useful product for home or cottage. There is a lot of examples. We will reveal the secrets of making the most interesting of them.

solar collector

In the article "" you will find materials on the manufacture of a collector from other remedies. Here we will tell how to make a collector from an unnecessary tank. It will serve as a replacement for central water supply during the summer period, and will also be indispensable in the country.

What you need for homemade:

water heater tank;
chisel;
a hammer;
metal brush;
black paint;
plywood sheet;
styrofoam;
glass;
bars 50x50 mm;
foil;
hoses;
mounting foam;
antiseptic for wood processing.

Progress:

To pull the metal tank, you will have to remove the facing.
Take a chisel and a hammer or a grinder. Do not touch the shell and thermal insulation, you need a fully cleaned container.
If it is covered with rust, thoroughly clean the surface with a brush for metal. After that, find the place of leakage and seal.
Degrease the surface, cover the black paint for effective warming up.
To raise the efficiency of the product, it is necessary to organize thermal insulation. For this, the housing is manufactured.
Collect the frame of a semicircuit bar. The design must be two times wider than the tank.
On the inside, overlook the frame of plywood sheets. From the outside, lay the foam, and again cover the plywood.
Inside the case, organize the stands so that the heater does not rolling. Attach the chalkboard to the base of the case, make marks and cut the stands.
If the collector is located on the street all year round, treat the drawer with an antiseptic and cover the paint.
Installation of reflective elements will increase the efficiency of heating helps.
Place the foil at an angle so that the rays fall into the surface of the collector.
Connect the water hoses to the discharges.
Cover the design with glass.
All slots Seal by mounting foam.

Conduct the container can be plastic. For the winter, water needs to be merged.

Mangal

What else can be made from the water heater? Want to be original - Collect the brazier with the stove. Initially, you will need metal pipes that need to be welded. They will serve as a firebox.

Top welding metal tank. Pre-cut it up the top.

In the inlet of the pipe, install the bar on which the firewood will burn.

Thanks to the bracket-rocket, the brazier supports the temperature well, so the meat leaves juicy.

You can make a brazier barbecue, as shown in the photo:

For this, a smaller part of the housing is cut off, put on the mounting to another part, so that the container with the lid was formed.

The handle is welding from above for convenient use, I will reduce the spreadshells.

Skolna from the water heater

The principle is similar to the mangal. In this case, it is advisable to use a boiler with a volume of at least 80 liters. Cut the upper part by 10 cm. Set the loop for the lid.

Also, the handle is welding on top, so the lid can be removable.

From the bottom you need to install a plate for collecting fat. Inside the design, holders for hanging meat are organized. The vent hole will serve to launch inside the smoke.

Burzhuyka furnace

Useful and compact device can be installed in any room. The main thing is the possibility of bringing the pipe to the street.

Prepare a housing. With the help of a grinder, remove all pipes and taps.
Make a shallow slot along.
Remove the casing and remove the insulating foam.
Clean the tank.
Calculate that the location of the Tan must be top.
Make markup for two holes: fireboxes and doors. Cut them.
Brew pipe holes.
Install the handles and latches on the doors.
The bottom of the construct is breed three or four supports.
In place of the Tan, cut the circle and install the tube for ventilation.

Water dispenser

If your boiler is dried, make a wash basin from it. To do this, clean the tank according to the technology described above. Cut the top of the top. Conclusions for pipes and fitting also need to trim. Treat surface: Clean, upload, paint. Inside the container can be covered with white paint.

One pipe hole Close the plug. To another install the tube and crane. At the cut part, attach the handle and organize the lid. It will protect the water from garbage.

Flowerby

Slowing capacity into two equal halves, you can use them for falling out flowers, greenery, vegetables. It all depends on the size. You can install products in the greenhouse. To do this, weld to the reverse side of the support, and the inner part fill the earth.

If you are projected, painting and beautifully arrange parts of the body, they can be used as a flower bed and an unusual decor on the street.

Bench chair

This is not a joke, but the idea of \u200b\u200bGreek designer Nelli Trakido. Today it is fashionable to redo unnecessary items in unusual and useful things for the house.

Using metal and paint tools, the designer turned an unnecessary tank into a stylish bench. As a support, legs were made from the old stool. Seats removable. Covers can be changed by mood.

If you do not know how to use unnecessary technique, show fantasy. Each item can give a second life. This example, the use of a water heater is not limited. Homemade masters make them receivers for compressors. More can be viewed on the video:

You can also organize an unusual garbage bucket. If the volume of the tank is small, the product will look stylish in the interior. Create!

The main advantage of the device is the economical spending of hot water at minimal costs. To heat the water, the wizard use different sources: electric tan, the energy of the sun, heat from the boiler. This article will describe how to make a water heater.

Construction of an indirect heating boiler

An alternative to Baku serves a gas cylinder.

Gas cylinder boiler

If you decide to make a boiler from a gas cylinder, it is better to purchase it new and without a valve. If an old capacity is used, then hot water can have a gas smell.

The balloon needs pre-primer. For this purpose, it is cut into two halves. In order not to have an explosion, we advise to pre-fill it with water. The inner part of the design is cleaned and ground. This is preventing rust. After that, the balloon is brewed.

Two holes are cut into the tanks intended for removal of hot and cold water. At the inlet of the cold water, the feed pipe is equipped with a check valve. This is how water flowing from the tank is prevented.

To obtain an indirect type heater, which will function from the heating system, in addition to hot and cold water taps, two more holes are made to install the heat exchanger. In it, one pipe is adjacent to another.

The coil is installed in the center of the tank or along its walls. The pipes are welded to its incoming and outgoing pipe.

If you want your device to stand, then the supports should be accepted. For attachments, loops will be required in the form of "ears".

To the place where Ten will be installed, a nut of 32 mm is welded. It must have internal threads. The water tang is desirable to be installed with the presence of thermoregulation or signaling sensor. Its power should be 1.2- 2 kW.

The result is an indirect heating boiler. In this case, the main element of the design is the gas cylinder.

How to make a snake?

The serpent is an important detail of the device. Behind it, you can take a metal or metal-plastic pipe with a small diameter. As a rule, copper or brass are used, as they differ in high levels of heat transfer. The diameter of the coil manufacturer can choose at its discretion. The main condition is that its contact with water is maximal.

The snake-shaped tube is screwed down the spiral on the mandrel in the form of a cylinder. For this purpose, a log or tube with a large dimension is used. When winding the coil must be monitored. They should not touch each other.

Do not draw a tight, because it will be very difficult to remove the coil from the mandrel.

The number of turns on the coil is directly dependent on the volume and height of the tank. As a rule, 1,5 kW of the heat power of the serpent is used for every 10 liters.

Heat insulation

So that the heat loss is minimal, the tank should be bought by a layer of thermal insulation.

For this purpose, apply:

construction foam;
isolon;
polyurethane foam;
polyneshane;
mineral wool.

Some craftsmen use a foil-based laminate substrate. The water heater is wrapped in this case, as a thermos. The insulation is attached by wire, glue or strip screed. We advise you to warm up the entire hull.

The casing will ensure not only the long-term storage of hot water, but will reduce the duration of the heating of the tank, which reduces the flow rate of the coolant. Without well-equipped thermal insulation, water in the device will quickly cool.

Often resort to the construction of double tank: a small tank is placed inside the large. The space created between them also performs the heat insulating function.

To secure the container, loops are welded on the upper part of its body, and the metal corner is installed on the wall to which they are attached.

Other Water Heater Production Methods

You can build a water heater functioning from the Sun. This is a fairly common design that is distinguished by efficiency. The device is often found in country houses. The manufacture of the device does not represent a special complexity, so many can construct it with their own hands.

You will need:

large tank (100 l and more);
pVC pipes for filling the tank and supply to it;
corners of steel size 20 mm or square bars made of 50 mm wood for a frame for a container.

It is advisable to use polyethylene barrels as a container. They are distinguished by strength. They must stand in a sunny place in which there is no wind. As a rule, for mounting choose the roof of the summer soul.

So that the barrel is better heated, it must be painted in black. Mounted screens to protect. They are constructed from boards covered with reflective foil material. In this case, the sun's rays are directed to the tank and increase the temperature of the water. In hot weather in a capacity of 200 liters, it is possible to obtain water, the temperature of which will be 45 ºС.

Polyethylene bottles water heater

Water heater with its own hands from ordinary plastic bottles can be made in one day. They constitute the basis of the accumulative tank. The number of bottles depends on the desired container.

For installation you will need:

sealant;
pVC pipes;
drill;
two valves or cranes with ball structures.

First of all, bottles are prepared. In the bottom of each, the hole is drilled, the diameter of which is equal to the neck diameter. In the bottom of the bottom of the bottle inserted the neck of another. So there is a connection. Each battery consists of 10 bottles. The number of batteries is not limited. All joints are processed by sealant.

Finished modules are located on the south side of the roof on the inner waves of the slate coating. The output of each section is connected to the PVC tube, which is perpendicular to them. The embedding of each section is carried out by analogy of connecting bottles into the battery, followed by the treatment with glue of all joints.

In the main pipe to which the outputs of each battery are connected, the valves for supplying cold water and removal are mounted on both sides.

This has a fairly high level of functionality. For the adoption of the soul, one person requires 100 liters of water. Relying on this indicator, it is possible to calculate the volume of the structure.

In the summer, in sunny weather, it is possible to heat 60 liters of water to 45 ºС. This temperature is quite suitable for household and economic needs in the country.

Conclusion

The rapid rise in price of energy resources makes many create cheap alternative fixtures. Many build a water heater with their own hands and create comfort with minimal costs.