Making a wardrobe in the toilet with your own hands. What are the cabinets for the toilet, an overview of models Sliding doors in the toilet for the toilet

Often there are problems with the place of storage of household chemicals. All sorts of powders, cleaners, rinsing ... they are becoming more and more, but they usually store them. The bathroom is too wet, in the kitchen is not too nice, as they can distribute foreign flavors, with cooking that are combined weakly, but rather, sucks are not combined. The exit, nevertheless there is a wardrobe in the toilet. Although usually the toilet room is small, but in it you can find a free place - above the toilet or behind it. That's it there and you can hang / install a dressing cabinet.

What material to do

When they decide to make a closet to the toilet, immediately arises the question of what material to do it. If we talk about furniture, there are options:

(LDSP);
laminated;
wood.

The cheapest material in this category is LDSP. Four times more expensive, MDF is obtained and more expensive - wood. If you collect doors made of cutting board or lining with your own hands, it may not be more expensive than MDF. But such work requires at least a minimum carpentry skill. If it is not, it will have to pay for the work of a specialist, which can significantly increase the final cost of the product.

If the locker is going to bonded with tiles, wake up with wallpaper, vinyl, plastic, you can use the materials other than those listed above:

phaneur;
GVL (gypsumole sheet);
sheet MDF.

All listed materials are quite suitable for the locker device in the toilet. The only thing, doubt may be about GVL: does he open in the place of fastening the loops? If large loads do not foresee, it is quite possible to use this material.

Matte glass and mirror - also possible options for facades for the cabinet in the toilet

Now the question is whether moisture-resistant materials are worth using. The cabinet to the toilet can be made from the usual material, provided that it is only a toilet, and not combined bathroom, i.e. There will be no high humidity in the room. An exception is the situation when it is done using a streaming window through the toilet. Such schemes still exist in homes with an old layout. In all other situations, the use of moisture-resistant materials is optional.

Falsten and Niche

In most apartments, the toilet is a narrow and long room. Its width about meter, the length is two or more meters. Such a long room is uncomfortable in use - the area to the door does not care anyway. You can improve the situation by installing Falsten. At the same time, the toilet can be moved forward, and the partition is cut down 50-60 cm. The remaining space is more than enough for comfort, and the one that will be "behind the wall", it is quite possible to use as a closet.

For this falseland, sewer and water risers will hide, which otherwise will have to close the special. The toilet space is optional to sew tightly. Here you can make a very spacious wardrobe. It can store powders, reserves of other chemistry, which is usually hard to find a place.

For the device will have to make the toilet forward, to the walls and on the ceiling to nourish the planks (40 * 40 mm will be quite normal), fill the horizontal strips that will hold the shelves. Doors for such a cabinet in the toilet are attached directly to the walls. Rather, to the planks that are fixed on the wall.

The bar needs a width of 8 cm. Since with open doors it will be in sight, it is desirable that it is finished with the same material as the doors. It is fixed with nails / self-tales / dowels to the wall, and to her - loops.

Cabinet to the toilet from floor to ceiling (or almost)

The cabinet for the toilet room can be a separate piece of furniture. He has a characteristic design that you do not confuse with anything. At the bottom of the cabinet to the toilet has two narrow and high stands that stand apart 50-60 cm. Over them is one or two sections with or without doors. These are already solid sections with swing doors.

Miscellaneous performance idea is one - the maximum use of all available space

The parameters of these cabinets depend on the size of the room. In stores you will not see such products, only individual order. From the same laminated chipboard will not be too expensive, but a lot of places for storage of chemistry.

There are more economical in terms of using the model space: at the bottom there are only struts, open and closed shelves are above the toilet tank.

The above option is good when the bearing ability of the walls is insufficient in order to withstand ordinary wall shelves. If you have a partition from drywall, porous or lightweight concrete, you can watch this side.

Hinged cabinets

Over the toilet, you can hang the usual attachment cabinet suitable width and height. It can be part of a kitchen headset or part of the hallway. In any modular collection you can find a suitable sample. We only have to cut into the rear wall of the hole for sewer and water risers, but this alteration is simple.

A mounted cabinet over the toilet: the height and facades are different ...

If worried that the open cut can be damaged by humidity, you can take a self-adhesive melamine and it to treat sections. An easier option is painting or induction with water-repellent sealant.

The height of the cabinet over the toilet can be different. As you can see in the photo above the model you can hang different - on two or three shelves (the total height of about 70 cm) or five - seven shelves (the total height is obtained from the meter and more). The most important condition is the cabinet should not block the vent hole. The second point: he should not interfere. That is, there should be access to the water descent button, as well as sitting on the toilet, you should not fight your head about the door. Based on these considerations and pick up the sizes of the hinged cabinet in the toilet. Since the parameters of the bowl of the toilet, the tank and the installation of the entire design are different, the depth of the cabinet can be from 35 to 60 cm.

What do do the doors

If the wardrobe in the toilet decided to do on their own, the shelves are usually not a problem: two parallel strips are stuck on the walls, shelves are stacked on them. Instead of slats, you can install furniture pollocks - they are different sizes and shapes, installed elementary. A hole in which the extended part of the holder is inserted into the wall. This is one type. The second is brackets that are attached to the wall. In general, it usually does not happen in this part of the problems.

But with what and how to make doors may be questions. The easiest way is to order the facade of the desired size in the furniture workshop. Order better together with the planks to which these doors will be attached. And you can also ask to cut the loops. Then it will be easy to install them: fasten to the wall and that's it. Possible facades: LDSP, LMDF, plastic, aluminum + glass or aluminum + plastic.

There is an option - make doors from the sheet material and go to them with the same tile, which was put on the walls. This is the case if you do not want the cabinet to stand out. You can also stick a mosaic of a suitable shade, use a flexible tile (sheet plastic under the tile), stick washable wallpaper, glass windows, etc. Options are actually mass.

To connect plumbing devices to the water supply network used flexible water lining. It is in demand when connecting mixers, shower cabins, toilet bowls and other points of water intake, and significantly simplifies the installation process. Flexible lining is also used when installing gas equipment. It differs from similar water tools for manufacturing technology and special safety requirements.

Characteristics and species

A flexible supply for connecting plumbing is a hose of different lengths made of non-toxic synthetic rubber. Due to the elasticity and softness of the material, it easily takes the right position and allows you to install in hard-to-reach places. To protect the flexible hose, the upper reinforcing layer is intended as a braid, which is performed from the following materials:

Aluminum. Such models are withstanding no more than +80 ° C and retain functionality for 3 years. With increased humidity, the aluminum braid is prone to the appearance of rust.
Of stainless steel. Thanks to this reinforcing layer, the service life of flexible water supply for water is at least 10 years, and the maximum temperature of the transported medium is +95 ° C.
Nylon. Such a braid is used to make reinforced models that hold the temperature to +110 ° C and are designed for intensive operation for 15 years.

A pair of nut-nut and nut-fitting, which are made of brass or stainless steel are used as fasteners. The devices with different indicators of the permissible temperature differ in the color of the braid. Blue is used to connect to a pipe with cold water, and red - with hot.

When choosing a watering for water, you need to pay attention to its elasticity, fastening and destination. Mandatory is also the presence of a certificate that eliminates the separation of rubber toxic components during operation.

Features of gas supply

When connecting gas stoves, columns and other types of equipment also use flexible liners. Unlike models for water, they have yellow and not tested for environmental safety. For fixing uses end steel or aluminum fittings. Distinguish the following types of fixtures for connecting gas appliances:

pVC hoses that are reinforced with polyester thread;
from synthetic rubber with stainless steel braid;
silphon, made in the form of a corrugated stainless steel tube.

Holding "Santekhkomplekt" offers engineering equipment, reinforcement, plumbing and fixtures for its connection to communications. The range is represented by products and materials of famous foreign and domestic manufacturers. With wholesale purchases, discounts apply, and product quality is confirmed by certificates of the established sample. For information support and assistance for each client, a personal manager is assigned. The possibility of making delivery within Moscow and to other regions of the Russian Federation allows you to quickly get purchased goods without unnecessary trouble.

Drainage - a hydro-elevative event on the disposal of excess groundwater.

If you do not leave the water from the territory for a long time, the soil is flunk, if they quickly disappear (swell) shrubs and trees, it is necessary to urgently take measures and carry out the drainage of the site.

Causes of soil moistening

The reasons for the convergence of soils several:

clay heavy soil structure with weak water permeability;
the waterproof in the form of gray-green and red-brown clays is located close to the surface;
high groundwater occurrence;
man-made factors (construction of roads, pipelines, various objects), which prevent natural drainage;
violation of water balance with the construction of irrigation systems;
landscape plot is located in a lowland, beam, hollow. In this case, atmospheric precipitation and water inflows are playing a major role.

What is fraught with excess moisture in the soil

The results of this phenomenon you see yourself - trees and shrubs die. Why is this happening?

the oxygen content is reduced in the soil and the carbon dioxide content increases, which leads to a violation of the processes of air exchange, water regime and power mode in the soil;
there is an oxygen fasting of the root-forming layer, which leads to the dying of the roots of plants;
violates the receipt of macro and microelements by plants (nitrogen, phosphorus, potassium, etc.), because Excessive water flushes mobile forms of elements from the soil, and they become inaccessible to assimilate;
an intensive decay of proteins occurs and, accordingly, the processes of rotting are activated.

Plants can suggest at what level groundwater

Look carefully to the flora of your site. Inhabiting its views will be prompted, at what depth there are soil layers of water:

ripowodka - in this place is best to dig up with water;
at a depth of 0.5 m - the bow of the village, the chests, varieties of the Oskock - bubble, ostolic, foxes, Vainik Langesdorf;
at a depth of 0.5 m to 1 m - Tollga, Canary,;
from 1 m to 1.5 m - favorable conditions for taming meadow, mint, mouse peas, ranks;
from 1.5 m - drink, clover, wormwood, plantain.

What is important to know, planning the drainage of the site

Each group of plants has its own moisture needs:

with a depth of groundwater from 0.5 to 1 m can grow vegetables and aluminum flowers at high beds;
the depth of the water reservoir to 1.5 m is well transferred to vegetable crops, grains, annual and perennials (flowers), decorative and fruit-berry shrubs, trees on dwarf dive;
if groundwater at a depth of more than 2 m, you can grow fruit trees;
the optimal depth of groundwater grounds for agriculture is from 3.5 m.

Whether the drainage is needed

Record your observations at least for a while. You will be able to understand how much drainage is needed.

Maybe it makes sense to simply redirect the tale and sedimentary waters along the bypass channel, and not allow them to flow through their plot?

Perhaps you need to design and equip the lavety and improve the composition of the soil and will it be enough?

Or is it worth making a drainage system only for fruit and decorative trees?

The exact answer will give you a specialist, to call which we strongly recommend. But after reading this article, you will gain some awareness in this matter.

At the end of the technological and production tasks associated with the arrangement of the sewer system in an apartment building, a production building, as well as in private home ownership, it is required to experience the system involved by the method of forced strait. This task is applied to identify possible defects or improper installation of the entire sewed sewage unit and the act of testing of internal sewage systems and drainage systems will be a real proof of work on the reception of the object.

Visual check should be accompanied by the test of the internal sewage and drainage systems in the ACT, which is currently submitted by the current regulations of the application of the "D" series, which corresponds to the joint venture 73.13330.2012 "Domestic Sanitary and Technical Systems of the Building" has recently applicable new Actualized working edition of SNiP 3.05.01-85.

The question of how to make a toilet for a toilet, occurs at first glance at this close room.

Here it is necessary to place detergents and hygiene products, other small items, and there is not enough space.

The locker located in an unused space helps to solve this problem, as well as give the toilet a certain attractiveness.

You can make such furniture with your own hands, but for this you should take into account the specifics of the bathroom.

Preparation

The only place in the toilet where you can put the repository for various necessary items are the space for the toilet.

It is small, and even occupied by sanitary devices, however, with the right approach, you can enter a fairly volumetric locker here.

It will not "eat" a useful space, but in order to become really useful must meet the specific requirements:

minimal depth. Furniture dimensions should not interfere with the use of the toilet, and therefore cannot go beyond the drain tank;
moisture resistance. The toilet refers to a room with high humidity, and the proximity of the tank and pipes increases the risk of direct contact with water;
the presence of ventilation holes To prevent the accumulation of evaporation inside;
security free access to plumbing equipment. In the area under consideration, cold and hot water pipes can be located, valves, cleansing filters and other nodes. The locker should not overlap access to them, even if these nodes are used very rarely;
attractive appearance.

By the installation method, the toilet cabinets are divided into built-in and hinged (case) types. In the first case, they fit between the walls or in niches and reliably, fixed inpatient. The cabinet is hung on the wall, and is manufactured as a separate, mobile furniture subject. It can be moved, removed for some time.

Of what?

Materials for toilet furniture are selected taking into account such requirements:

sufficient mechanical strength;
low weight;
water resistance;
external appeal;
simplicity of processing in the manufacture and cleaning during operation;
environmental purity.

If they do not have sufficient moisture resistance, there is a need to impose protective coatings or conducting a special hydrophobic impregnation.

Most often, the following materials are used for the manufacture of cabinets:

plasterboard. For toilet conditions, water resistant varieties are suitable. Sheetsockarton sheets are easily processed and enough racks to the action of condensate and moisture are not susceptible to rotting. The appearance is given by staining in the desired colors. The disadvantage can be attributed to low mechanical resistance to bending, as well as fragility of angles and edges;
plywood. For bathrooms are quite suitable for modifications of FC and FSF with increased waterproof. Usually used sheets with a thickness of at least 14 mm. It should be noted that the FSF typeer is contained phenol formaldehyde, which at elevated temperatures may be released from the material;
wood. When making a frame, a wooden bar is most often used. The board can be applied for the door. The main disadvantage is rotting under the action of moisture, which requires the impregnation of the material with special compositions;
laminated chipboard (LDSP). Increased water resistance allows you to use it as shelves, doors and housing in the mounted version. When choosing this material, it should be taken into account its significant mass, which leads to deformations under the action of their own weight. This circumstance requires the use of hardening elements (rigidity ribs);
metal. When making a frame, an aluminum profile is often used for fastening of plasterboard or metal corner. Metal has a high mechanical strength, but steel elements require reliable protection against corrosion;
plastic. Dense plastic panels are widely used as doors. A variety of colors makes it possible to ensure the desired design. Important benefits - low weight and absolute waterproofability.

The choice of materials for toilet cabinets is made taking into account the selected design, sizes, design solutions.

Council. Thickness should be optimal - ensure the necessary strength, but not to increase excessive weight.

Scheme and drawing

Before the start of the manufacture of the locker, it is necessary to produce a way to place its placement in a particular place. To do this, the space behind the toilet or installation is thoroughly, as well as the location scheme of sanitary nodes, to which it is necessary to leave access. It is provided by special slots, holes, hatches.

Based on the composed scheme, a drawing is developed with full detail and reference to the installation site. The design of the locker is quite simple - frame, upper and lower panel, shelves and doors, as well as if necessary, the rawpanel (rear wall).

Council. The frame can be installed on the entire wall behind the toilet or occupy only the space above it and the drain tank.

Typical toilet in apartment buildings often has 82-85 cm width. With this size, the extreme panels and shelves are mounted on the entire width. They make cutouts for passing pipes. The depth of the locker is installed in the magnitude of the tank retreat from the wall. As a rule, it is 30-40 cm. At the same time pipes require cutout up to 25 cm long.

Doors can be several options. Most often installed simple, swinging flaps (2 pieces). You can use projects with sliding flaps and roller blinds.

Instruments

For the manufacture and installation of the locker in the toilet, you must take care of such a tool in advance:

perforator;
bulgarian;
electric drill;
screwdriver;
electric jigsaw;
plane;
hacksaw;
scissors and hacksaw for metal;
a hammer;
chisels;
pliers;
paint brush.

To carry out measurements and quality control, a construction level will be required, plumb, roulette, metal ruler, as a carbon.

Manufacture

In close toilets most in demand built-in locker option. It is installed between the walls behind the toilet and closes the rear wall. After the design of the drawing and the installation scheme, you can proceed to the manufacture and assembly of this furniture. First of all, the installation location is carefully prepared. Walls need to dry well. Believe all dirt and damaged coating. If necessary, lines the surface of the walls.

Council. If there are places with mold or fungus, they are carefully cleaned and processed by copper vigor.

Framework over the toilet

The first step of installation of the cabinet - installation markup. If the cabinet is height reaches the ceiling, then the markup begins with its surface. There are extreme points that limit the depth of the cabinet. They are lowered by a plumb for checking the location regarding the borders of the drain tank. The mark should not go beyond its limits. The line is watched - the boundary of the front part. It should be strictly perpendicular to the side walls of the toilet.

Next, is carried out marking of walls. The lower point is set, retreating from the top of the tank for the distance required to maintain its handle when operating. Through this point the line parallel to the floor is drawn.

Using the level, this markup is transferred to the opposite direction so that both lines are in one distance from the floor. Then, the location of the shelves inside the cabinet is noted on the walls.

If the height cabinet does not reach the ceiling, then all the marking is provided on the walls. Initially, the lower boundaries are noted according to the specified technique.

After that, they are measured from them the desired height of the locker (according to the drawing) and lines are stuck, strictly parallel with the lower markup.

The most common design of the toilet cabinet is the bottom and top wall (panels), rigidly connected by vertical racks.

Council. Most often, the frame is collected separately, and then, inserted into the simpleness and securely fixed.

As racks can be used wooden bars measuring 30x30 mm or aluminum profile. Hard panels from LDSP, boards or thick plywood can be directly sealed. For the manufacture of plasterboard panels, first, a frame of a metal profile is assembled, which is sized with a sheet of plasterboard.

Before assembling the frame in the bottom panel, and, if necessary, in the upper wall, a plot for docking with pipes is cut. To do this, a slot is made with a width equal to the diameter of the pipe, on the length of the distance of the highway from the wall of the toilet. At the end of the slot, a semicircle for rises of a pipe is formed. Such a slot allows you to "wear" the panel to the pipe so that its long-round edge reached the wall surface. Their number on the panel depends on the number of highways.

The frame assembly when using bars is provided with metal corners. If an aluminum profile is joined, special self-tapping screws are used. The collected design is checked on the verticality of the racks using a plumb and the horizontal panels using the construction level.

The locker frame is installed on the selected place, focusing on the markup. Racks frame attached to the wall dowels with a step of no more than 30 cm. To do this, the corresponding holes are made before installing in the wall with a perforator.

Important. If the walls of the bathroom do not possess perfect verticality, then the gap is formed between the rack and the wall surface. It should be placed on the gasket-compactor, providing a more rigid fastening of the frame.

Shelves

Shelves of lockers most often made from LDSP, waterproof plywood thickness 15 mm or boards.

Before installation, it makes slots for pipes along the above method. The spears are made in the corners for the rises of the vertical racks of the frame.

To install the shelves between the frame racks on the wall markup on the wall, crossbars are fixed from a wooden bar or an aluminum profile.

The ends of the shelves fall on these crossbars and are attached to self-drawing.

Doors

The highest demands are presented to the doors of the toilet cabinet, because They create a certain appearance. The following methods of their manufacture are distinguished:

When fixing the door sash, it is important to ensure their symmetry and strictly vertical location. Between them should not be a gap.

Important. Opening should be easy, but with the exception of self-diskupy.

Decoration

The final stage of the manufacture of a locker is to give it an attractive appearance.

Wooden doors sufficiently covered with waterproof varnish in several layers. Fits good alkyd-urethane varnish.

Before lacquering, you can ensure toning with morlogs or special compositions that emphasize the structure. Chipboard and plasterboard will have to cover primerAnd then paint in the desired color.

Council. Plastic itself provides the decor, and therefore it is just necessary to pick up in color.

An important role is played by fittings. To ensure the retention of the door in a closed state, magnetic elements are installed. The decorative type of shelves helps the P-shaped aluminum or chrome profile, which is fixed on the front edge.

Door handles must be not only comfortable, but also beautiful. Their assortment is huge, and therefore it is necessary to choose with a general design (in color, size and form). Finally, you can use plastic moldings that are able to give any surface attractive appearance. In addition, the edges of the doors are desirable to cover with decorative strips of plastic or metal. If you need to fix closed doors, you can install the latches of the type you like.

Useful video

Alternative implementation option can be viewed on the following video:

Conclusion

The locker in the toilet will help to take the small space that still remains unused. Its accommodation for the toilet at the level of the drain tank allows you to solve the problem with the storage of the necessary things without creating inconvenience. You can make this outdoor furniture with your own hands, given the features of the room.

In contact with

06/26/2014

After repair, a hole remained in the back of the toilet room. Here is this:

It would be wrong to close the tightness, because the pipes! From above is the main valve, overlapping cold water in the toilet and bathroom:

Downstairs is the water supply, sorry to the toilet bowl. Again with the valve:

I would like to look at the sewer riser too. Well, little, suddenly throws, or something else. But the most important thing is the disappearance of the place where any economic trash could be downloaded, so as not to corulil his eyes.

In the process of repairing the toilet, the appearance of the cabinet did not invent. The problem was in the location of the tiles. The most obvious option is to make two doors equal to the width and put on top of the same tile as on the walls. However, the middle then would hit the middle tile. And if you saw, then there will be a "somehow neakkuratnyko". And if you do the doors of different widths, then one of the doors will get too big and will again be "neakkuratnyko". Actually, scored on this thing in anticipation of the arrival of a good idea.

And the idea came. To hell with a tile, give glass!

In QCAD "E was drawn to the plan:

In the Castor, the boards of 200 mm width, varnish, paint and other related elements were purchased.

Well, I will proceed. First cut out the interweony of a vertical profile. In order for the strength of the remaining design not to suffer a rack of a dowel-nail. Around the dowels we leave the "ears". They will then hide under the boards and we will not interfere with:

We start collecting the cabinet box. We try the vertical walls. Right with a neckline:

Horizontal roof walls:

Design we will collect on the glue and the wanks:

Insert the already collected design will not work, because the tiles on the walls will interfere. Therefore, we will collect everything in place. In horizontal walls we make grooves:

The accuracy of the split connection provides a special conductor purchased on IBEY:

We place and drill holes for the power holders:

Usually use drill on a tree with a limiter, for example, this:

But you can and so:

For each shelf, we make 3 pairs of holes so that you can adjust the shelves in height:

We are trying on the walls with the installed fixtures:

Sewer riser is not vertically, so for each shelf the pattern has to be adjusted.

We try:

Cutouts for tap pipes are made at the place. The shelves are regulated in height, so we make cutout under the riser with a reserve:

Take a transparent aqualak. It does not stink and dries quickly:

We do not use the veil, for the tree under the transparent varnish is exactly the tilt of the wall tiles.

Lacuate all the shelves and boards of the box. In 5 layers. After each layer, all parts are sanding.

Color "Terracotta":

It comes up to the color of butterflies on the tiles.

We protect the painting tile tile edges. Mobile wall and pipes. This is the first layer:

Then a couple more layers.

Install the side walls. Break them to the walls of the mounting foam. Install and glue crossbars:

Install the shelves. At this stage, an unpleasant moment was found - periodically occurring condensate on the pipe of cold water in the valve area. In the upper right corner you can see raw crane:

It is bad, both for paint on the pipe and for the shelf. It is necessary to somehow thermally insulate the pipe in this place. Considered options with thermoflex tubes. But it is not clear how to organize a hermetic connection in the crane area. In short, there was no obvious decision, so postponed for later ...

The next stage is the doors. Also turned out to be a kind of quest. It was necessary to find a banal glazier who would cut the desired piece and speckled ends. The workshop that was before was near the house closed. Glass ordered in the workshop at: Chaliapina, 2a. There's another store "Furniture Dvor".

The rational use of the bathroom space largely determines the level of its comfort, and the aesthetic component is important for giving the premises of comfort, attractiveness. Such a plumbing element like a locker to the toilet helps to achieve these goals. If there is a similar product, use the toilet will be most convenient as possible.

The bathroom is one of the most important premises of the house, and errors in its arrangement may affect the comfort of life. To increase the ergonomic characteristics of this space, it is worth selecting functional, beautiful, durable cabinets in the toilet.

Furniture of this plan has a huge number of advantages and allows you to solve many important issues in the arrangement of the bathroom:

waving communication (sewer and plumbing pipes), you can give the room an attractive, neat look. Nude pipes, hardly, call beautiful, and their design rarely fit into the apartment. Therefore, you should not leave them without attention. Correctly picking a locker, it will be possible to get to communications at any desired moment, which is extremely important when breakdown;
featuring a spacious model, you can provide yourself with an additional place to store household chemicals, cleaning items. If you split the space inside the product on the pipe zone and for the shelves, you can save a decent bathroom space. This is especially important when the room has small sizes, such as in Khrushchev;
if there is a meter on water, it can also be hidden into the locker to the toilet. Thus, you will ensure trouble-free access to the equipment, but hide it behind the facade of furniture for greater aesthetic interior.

The advantages of such furniture mass, it is for this reason that it is so popular today among owners of country houses and apartments. But most of them are revealed if a quality product is purchased.

Product options

Modern toilet cabinets are very diverse in operational parameters and appearance, so the consumer can easily choose a model in any style, depending on the decor of the bathroom of a particular size, colors.

We describe the most popular types of lockers for the toilet. By type of door distinguish plumbing products with:

the louvre doors of two types: rolling and "pseudo-gas". The first option is convenient for a small bathroom due to its compactness. The door does not break off, for which the additional space needs, and it consists, rising up. Therefore, the louvral models can be hung in uncomfortable places. The second option is a conventional facade made in the form of blinds, but without the presence of moving slats. Such a door allows the internal contents of the furniture to be perfectly ventilated;
plumbing hatch, which closes a niche with pipes. In practice, the hatch is a conventional frame from the corner to which the door from the metal with the lock is assembled with the help of loops. Note that such a decision will not cost expensive, but it looks like a hatch is not always stylish, expensive;
swing facades - such structures are better to make to order. They are diverse in design, dimensions, functional and practical;
coupe doors - this design does not require an additional place to open the door, as it simply moves for the second facade.

Blind

Swing

With plumbing hatch

Based on the manufacturing material, highlight models from:

natural wood - dear, beautiful, durable material. But it is worth remembering that when combining the bathroom and toilet, the life of a wooden locker can be reduced. Increased level of air humidity negatively affects the quality of surfaces.
MDF - the cost of structures from MDF refers to the category of medium, but under the influence of water, the material it can lose its form;
The chipboard is the most unwanted option for a combined toilet with the bathroom, since the chipboard quickly absorbs moisture from the air and swells. But for a separate toilet, the chipboard is the ideal option at cost and external aesthetics;
plastic is the most practical option, as the plastic is completely not afraid of high humidity. But the appearance of plastic models is not always aesthetic. This is rather a budget option.

Wood

Plastic

Glass

Based on the shape of the product, cabinets are distinguished:

rectangular - standard products that are selected for the bathroom more often than the rest;
corner triangles - perfectly fit into the angle space, which allows it to be rationally planned;
corners in the form of a trapezium are more specificated than a triangular model;
radius - possess an unusual design, but it is quite expensive.

Methods of accommodation

If the sewer pipe passes in a niche, it is worth choosing a standard rectangular or square cabinet in the toilet for a toilet. This is an ideal solution that allows you to give the Communications an attraction. The main thing to guess with the size of the model so that it successfully fit into a niche. If I want to save, you can not get the finished closet, and choose a hatch with a lock, with which it is closed with a niche with pipes.

If the pipes are concentrated in the corner of the room, then you should stop your choice on the corner of the cabinet. Such designs are characterized by high capacity, and their design will allow the toilet a pleasant look.

Additional functions

In small bathrooms, it is imperative to endure all furniture items with high functionality, practicality, to use the room as convenient as possible at any time of the day. It should not forget that the design of a small space also affects its comfort. Therefore, the models of cabinets in the toilet must have additional features. Such a product is represented in the photo in the selection.

With a mirror

With backlit

How to choose correctly

If the bathroom design is selected, it will be left for it a suitable cabinet model. When choosing a mini-size toilet cabinet, it is important to remember the following:

initially, it is necessary to determine the choice of the product shape. If there is a niche, choose built-in models to order, if not - you can choose more costs, ready-made models;
next, perform measurements of space to understand the wardrobe of which scale successfully will fit into the bathroom. Measure the parameters of the pipes that hide in the cabinet. Be sure to sketch the schematically features of their location before leaving the furniture store;
select the current color solution and design of the plumbing element, which will perfectly complement the bathroom decor;
ask the seller a quality certificate to the product, which will be a guarantee of a long service life of furniture, its practicality, high quality applied materials in the process of its manufacture. It is also important to clarify the presence of fasteners and other components. If, in addition to the model, the bracket or hardware is not underway, you will have to purchase similar fasteners separately. They will enjoy the installation of the design on the wall surface.

Remember, the cabinets in the toilet photo of which are presented below should be harmonized with the decoration of the room, supplement it with its beauty. Then the room will look more concise, holistically.