How to put podiums. Acoustic podium: photos and possible creation options. Photo: Step-by-step manufacture of plywood shelves

To ensure high-quality sound audio system, motorists use not only good car radio, but also subwoofers, as well as amplifiers. However, not everyone comes to the idea of \u200b\u200bsetting the podiums for car speakers. Read more about the purpose, as well as the manufacture of these elements, you can read below.

[Hide]

What is the podium for speakers?

If you decide to equip your car with podiums, then you probably know what they need. First, these elements allow you to provide a clearer tracking of the track, while delivering it from the ghosts. Secondly, thanks to them, the transparency of the sound will improve and low frequencies will be added. Thirdly, if you acquire a good acoustics, then the columns usually have non-standard connectors, respectively, the podiums under the dynamics of 16 inches or other sizes will solve this problem. In general, thanks to these elements, a more surround sound is ensured that it cannot but rejoice Melomanians (the author of the video is the RomanAutoreView channel).

Manufacturing and installation instructions

Before making podiums at home, you need to take into account a few moments. First of all, note that these devices must be made of wood, since this material is well combined in an acoustic plan with an iron body car. If you have a regiment under the radio, it can also be installed wooden podiums.

Form of Podium

The form of elements can be absolutely any - in this case it all depends on the fantasy of the motorist. But choosing the form you need to calculate everything, in particular, so that the podiums for the speakers do not interfere with the opening of the doors. When you decide on the form, you will need to take a cardboard sheet and draw it on it, then cut.

Playground under the speaker

Make measurement columns for radio, as well as a protective grid. Draw on the cardboard the corresponding ring with the fact that its inner diameter must match the size of the place to install the column. The outer diameter must match the size of the protective grid.
The resulting layout should be transferred to the paneur and circle with a marker or pencil. The thickness of the material from which the podiums are made should be about 7 mm.
Next, two forms of the device are cut down, in the same way, we do with rings - the decorative part must be glued to the base, for more reliable fixation it can be fixed with cloves.

Build construction

To assemble the ring, it is necessary to fix well, for this you can use spacers. Spacers themselves can be made of any material, a tree is usually used. As in the previous case, for greater fixation you can additionally use the screws.

Filling podium

It is most convenient to work with the mounting foam, but this option is not particularly durable, as an option, you can use the epoxy resin:

In advance in the ring, install the package (it will be needed in order not to use an excess foam).
Foam is applied with smooth layers from the base of the ring. When it dries, all unnecessary plots must be cut off. Using sandpaper, it is necessary to produce a grinding of the podium.
Further, the design you can apply a putty mixed with PVC glue, this will prevent sopping. The spacure itself is applied in several thin layers, and each of them needs to be given to dry. When the material is dry, the design again will need to handle the sandpaper.

Features of the dressing of homemade podium

The podium made can be covered with artificial leather, this option is very popular today, because in its properties and visual appearance it looks like a door trim. As a rule, tensioning is carried out from the ring to the ends of the product, each side for better fixation must be pulled several times. For more convenience, you can use a construction hairdryer, and when the tight will be finished, a stapler can be used for fixing. Excessive part of the upholstery material should be cut off.

Finishing Strike

After the design is ready, it is possible to install it on the door or shelf of the car. As a rule, the device is fixed using selflessness. Of course, before this it is necessary to completely remove the door trim and dynamics. After the podium is installed, it is necessary to check the sound quality of the speakers - only when you understand that everything suits you, the design can be securely fix and collect the door.

If you want to achieve the best sound, then you will not existently insulate your car - for this, special noise-absorbing materials are used. You can also achieve high-quality sound by adjusting acoustics.

Question price

As for the price, it all depends on the manufacturer, the material from which the podiums are made as well as the quality of the upholstery material. On average prices for podiums are as follows.

Video "Visual manual for the manufacture of podiums"

As with your own hands, to build podiums at home and what nuances should be considered - a more visual instruction is presented in the video below (the author of the movie - Avto Class channel).

All the time of the day! I decided to tell a little about how I did (almost left to leave the skin) podiums under Midbas. Making records about each stage is very tedious, and who needs it, everyone wants the result. So soon there will be a result - let's go!

Heat the rings from the artificial stone of the preventery under the angle of 60 * the inner walls.

One thing is smaller to the dynamics, second to the door
Put up with Chinese sticks and thermoclause direction

Most it
The second base is absolutely mirror.

Brothers Blin
The inner part shoved in two layers by painting scotch

waiting for the continuation
The space between the rings from the outer side was poured with a polyester with fiberglass, waited for the Hydroyony cut off the unnecessary

beauty
The remaining space filled with putty with fiberglass, polished. Then removed the small flaws of the finish putty

Preview
The inner wall also covered the finish putty, although after the branch of Scotch, she was almost even smooth, but still, and he also wrote everything. After all the "skin" procedures covered the bases of the podium three layers of the soil on plastic and two black enamels.

beauty
Next Stage Production of Outdoor Podium

Using a pre-made metal ring and cutting standard nuts of the dynamics, markup and drill holes for fastening bolts

Fitting on boarding holes
And cutting the threads under them in the bases of the podiums fix them, having previously sailing with painting tape for the door.

In place
Because I decided to make a lining on the outside door, then the door card must also be prepared, after having passed the same scotch tape in place.

With the ring of the decorative part of the piled with a manual milling and stuffed on the heat
We apply fiberglass with a polyester pre-winding the fiber on the glass until it becomes plastic and militant seconds 30-40 is no more, and then it starts to break down the layers, and part of the fiber remains on the glass. I threw it somewhere layers 5 and left all this business to dry for a day.

We are waiting for 24 hours
The next day, all this matter is separated carefully and give the dreamed preliminary shape.

Something like this
Having tried on the door, glancing by the result, we are tightening the billet in Lycra and impregnate the polyester resin

We are waiting for a day
After drying, we put 3 layers of fiberglass, we are waiting for an hour - one and a half

In the process
After hardening, we cut everything with the same dreamed, everything is superfluous, we applied a thick layer of suitable fiber powder, we are waiting for drying for 20 minutes and then long and stubbornly all this business to bring to the form you need

Almost done
Well, and then, everything, as always, 3 layers of soil, 2 layers of paint and voila!

Dry
After drying, it is natural to see what happened there, and how it looks assembled.
Blucked to two-way scotch, in order to admire the preliminary result)

Like)))
While only painted, I still wait for a tight fabric, which one in one repeats the texture of the door card, there can be a little more something that lifting something, but for now ...

Something like that, the next stage is the preparation of doors. Also an interesting and time-consuming event, but one thing I can say for sure: each invested part of the soul, forces, and time, certainly leads to the result, which every step more and more like it!

Thanks to all! To new meetings!

Car owners and motorists probably faced the problem of the bad sound of their audio system in the car. Solve this current problem can be a small refinement of the car, as well as the installation of new mounts. speakersMade do it yourself. The article below shows the process of improving the audio system on the basis of the domestic car VAZ2106 and of course this idea can be made on any car. The main task in the project was setting 16.5 cm speakers in the podiums on the door of the car.

Development of the design of the bottom of the podium

A very important point in the design of the podium is the form of the podium itself, since it serves as the basis for the whole design. The main task is to work with the mind, carefully so that the innovations do not spoil the appearance of the cabin, and also did not interfere with the convenient use of the door opening knob, the window holder, so that nothing superfluous prevented the tight closure of the doors. The form of the base of the podium is drawn on the cardboard, then cut the contour.

The next stage of work - on the cut-cut template, draw the part on the plywood 6-8 mm thick. Electroblzik, or another manual tool, drink two details for the right and left car door.

Playground under the speaker

Next, you need to start working on a decorative ring, which will give a more aesthetic appearance of the structure itself. After measuring the dimensions of the dynamics and its protective mesh, you need to do the landing ring in the plywood. The inner diameter of the dynamics of the dynamics must correspond to the diameter of the rings of the speaker itself. The outer diameter is equal to the external diameter of the protective grid. To this measurement you need to add 5-6mm for the decorative ring.

Cut the decorative ring pattern from the same material, from which we cut the podium. Decorative ring with glue and glue to the base of the structure. For greater reliability, after the adhesive will dry, the decorative ring must be nailed to the base with nails.

Attach rings to base

Rings need to be attached to the very base of the rails with wooden or metal, which are cut in advance by the appropriate dimensions, which depend on the degree of inclination of the ring relative to the base, as well as your desire, how much you want to make the dynamics. The slope seeks the direction of the dynamics. One speaker you need four rails that are fixed ring to the base.

The consoles are attached to the base and to the ring by self-draws. Hard fastening them - provide durability and reliability of the design.

Mounting foam as a filler.

To give the form of bend, use the mounting foam. After it dries out of it, it is possible to cut rounded shapes without sharp corners, also the foam material is easily processing. In order for the foam consumption is moderate, you need to insert a metal or plastic pipe into the hole, put on it in advance cellophane, so that after hardening the foam, the pipe can be easily removed from the hole.

Foam is applied with a smooth layer, ranging from the ring with a circular movement to the edges of the podium. When the foam has not yet managed to dry, if necessary, apply the second layer of foam, especially around the decorative ring. Bole is convenient to cut up more superfluous after frozen the foam than apply a repeated layer again and wait when it dries.

Giving a frame of the necessary form

After the foam is finally dried, you can proceed to the most responsible operation - cutting foam, and the formation of the workpiece of the future fastening of our speakers. For this, a sharp stationery knife is cut off excess foam.

You need to start first on the basis, then on top, and then slowly give the form of our billet. After the process of removing an unnecessary foam is completed, bring the shape of a coarse-grained sandcar to almost the perfect state.

Surface leveling

Align the surface, we apply a thin layer of putty mixed with PVA glue. This process is needed to prevent sinking the frozen foam filler. It is better to use fiber-based fiber-based putty in this process.

We apply one layer of putty. After drying the first layer, we apply the second and third as needed. After complete hardening, the putty finally processes the surface to the desired state.

To protect the podium from the mechanical effects of the podium, it is necessary to push the fiberglass impregnated with epoxy resin. Epoxy resin needs to be mixed with the hardener follows the instructions. It is applied to a smooth layer on the surface of the podium. Then we put the fiberglass on the podium and carefully smooth out the rubber spatula. It is necessary to prevent the formation of folds so that the fabric is completely repeated the contours of the podium. We impregnate the surface of the tissue with epoxy resin, and so leave to dry.

After complete drying, the residues of the fiberglass cut, and also remove the excess epoxy resin.

We are tightening the podium of artificial leather

The final stage of manufacture is the tightness of the podium artificial leather. The priority of pulling is approximately specified in the photographs of the arrows, as well as the sequence of actions. The construction hairdryer helps soften the skin and smooth it with a smooth layer. Lastly, the skin of the ring stretches and is fixed with a stapler, excess artificial leather are cut off by a stationery knife.

The podium is fastened to the doors of the car using self-tapping screws, screwed onto the back of the trim in the base of the podium. The covering is collected again, with the podiums installed on it, the doors handles are screwed, all decorative elements are installed.

For more reliable fastening of the podium to the door, special performs are provided, you need to look as indicated in the figure. With their help, you can pull the base of the podium design itself to the iron base of the automotive door. This allows you to create a tougher design.

Podium is an interesting designer solution used by the Old Roman architects to arrange residential buildings and public premises. Modern designers using the podium "align" the proportions of space and share the room into several functional zones.

The article describes in detail the technology of manufacturing the podium with their own hands, provides practical advice on the placement of self-made design.

The role of the podium in the interior of the room

The podium design resembles a step, high up to 25 cm. If you need to raise the podium to a height of more than 25 cm, then a multi-tiered design with a wide top platform is built.

As an element of the interior, the podium can be erected with a decorative goal, and at the same time, to perform a number of practical functions.

Zoning space. "Raising" part of the room can be visually allocated part of the room and make the necessary accent in the interior. According to the laws of perception, items located above attract attention in the first place. On the podium you can equip any functional zone: office, dining room, kitchen, bedroom, nursery.

Especially relevant to the use of the podium when making the interior of a multifunctional room, such as a one-room apartment or an apartment studio. The autonomy of each zone is highlighted by the floor level.

Adjustment of the proportions of the room. With the help of the podium, you can change the visual perception of space and give the room to the right forms. The narrow room "expand" with a rounded form podium, and the angularity of the square room can be hidden by installing the corner podium.

Expansion of the useful area of \u200b\u200bthe room. In the design of the podium, it is possible to provide storage boxes for storage, which is very convenient in small apartments.

Placing communications. In the frame podium, you can hide different elements of communication systems, video and audio equipment, wiring cable. In the bathroom, sewer pipes and other engineering communications are masked under the podium box.

Using the podium as furniture. From the podium you can make a cozy sofa, upgracing it with a foam rubber and drapeted with a cloth. An ordinary bed can be replaced with a frame multi-level design. At the same time, the sleeping place is located on top of the bed podium or put forward from the podium niche. In the second variant there are additional possibilities of using the podium - the construction of another on the functionality of the zone (cabinet, living room, children's, home theater).

Additional source of lighting. At the end of the design, you can install LED tape or small decorative light bulbs. The lighting devices will emphasize the interior stylist and will be able to be used as a backlight for the recreation area in the bedroom or living room.

Choosing a type of podium and material design for its manufacture

Depending on the design, all podiums can be divided into two groups: monolithic and frame.

Monolithic podiums Made from cement-sand mix, plaster bok or foam concrete. More often such a structure is erected in bathrooms and kitchens of private houses.

The advantages of whole structures include:

base strength;
podium durability;
simplicity of manufacturing and installation;
the possibility of applying any finish, including ceramic tiles;
resistance to moisture.

Disadvantages of monolithic podiums:

the finished design has a very large weight;
inside the podium there is no place for storing things;
access to the stamped communications is limited;
forty height of concrete podium - no more than 15 cm.

Frame podiums - A more common and functional type of design. The base of the podium is made of metal products or wooden bars, a frame of a frame - plywood (20 mm).

The advantages of frame podiums can be attributed:

multifunctional design (placement of communications and storage systems);
ease of installation;
the ability to create high, multistage profiles;
ease of construction.

In order to make the frame podium, it is reliable and durable to ensure the stiffness of the structure, installing intermediate lags

There are no restrictions on the installation of frame podiums, they can be built in apartments in country houses, cottages, etc. The main thing is to choose the right material for the construction of the frame and finishing the podium.

If the podium is installed in a room with high humidity (kitchen, bathroom), the framework is made of metal products, and a wood-polymer composite or tile is used as a sheat.

For the "dry" premises, the frame can be made of wooden lags and bars, sheathe the basis of OSB plates or multi-layer plywood, decorate the podium - linoleum, carpeted floors, textiles, wooden sexual rail, parquet or laminate.

Lags made of glued vehicles need to be treated with impregnation against the formation of fungus and fire

Deciding with the design and material of the manufacture of the podium, you need to select the optimal place for the elevation.

Rules for posting the podium in the apartment

The seat under the podium should be chosen, given some factors:

Construction of the frame podium under the bed with your own hands

Preparatory Stage: Podium Scheme, Required Tools and Materials

Consider the simplest version of the manufacture of beds-Halfium with drawers. Sleeping space is located above the podium. This design is usually used for zoning space.

We proceed to the manufacture of the podium with your own hands. Drawings and design sketch should be displayed on paper, indicating all sizes:

height, length and width of the frame under the podium;
dimensions of drawers;
height and width of the board stage holding the mattress;
height and number of supporting lags;
sizes of headboard and backrest;
the dimensions of the stage of the podium;
the presence of additional elements (racks, shirms, partitions).

The list of necessary materials for creating a podium bed with dimensions 193 * 165 * 35 cm:

From the tools you will need:

electrolovka (knife);
screwdriver or drill;
cruciform screwdriver;
roulette;
a hammer;
construction stapler;
pencil;
construction level (tool length - from 1.5 m);
line.

Frame maturity sequence

We will describe in stages, how to make the podium do it yourself:

Ready podium do it yourself: photo

To separate the podium bed from the rest of the room you can install homemade racks or shirma. The design of the improvised partition should complement the style of the design of the podium bed, and be it a peculiar continuation.

Production of the podium with their own hands: video

Technology of manufacturing monolithic podium in the apartment with their own hands

The monolithic podium can be made from concrete or make a "lightweight" version of a solid design using instead of gravel - clamzite, and instead of a brick formwork - a frame made of metal profiles or plasterboard sheets.

Construction of concrete podium:

At the external perimeter of the podium, lay a brickwork.
The adjoining of the podium to the walls is additionally not necessary.
Place inside the podium the necessary communications. This is usually done when creating a podium under a shower cabin or bath.
Pour a concrete solution (sand + gravel + cement).
On top of the concrete box, until the solution frozen, put the masonry mesh.
Stack the side walls of the podium.
Separate the podium tile or other material.

Creating a solid podium from a ceramzitobetone:

Metrolery carcass on the perimeter of the podium.
The outer part of the metal frame is tinted with plasterboard.
Ready frame filled with ceramzitobetone (sand + ceramzite + cement).
Podium is ready for finishing finish.

We give practical advice for those who decided to make the podium alone:

Production of the podium is a great way to update the interior of the room, add stylish rooms, originality and functionality. All work on the creation of a hill can be made independently, saving significantly on the payment of specialist services. Of course, you will have to spend money on building materials and stock free time, but the result is worth it - the podium will change the usual perception of space.

Under the sound of favorite songs and musical compositions. For this, many drivers buy expensive amplifiers, subwoofers, stereo. At the same time, the speakers are installed not only under the rear glass, but also on the doors of cars, which allows you to get a clearer and high-quality sound. However, setting the speakers in the state form, it looks not so beautiful. To decorate even the usual speakers and install them on the door, you can easily make the podiums that we will do now.

So, in order to make podiums for speakers on the door of the car, we will need:
- cardboard;
- stationery knife;
-saw;
- chipboard;
- glue;
- sandpaper;
- file;
- self-tapping screw;
- Carpet.

Materials figured out, now you can start making our podiums. We take a piece of cardboard and a stationery knife make a template of future podiums.

Now we use our template for the manufacture of three layers of the podium. To do this, we take 15 mm chipboard and squeak the saw through the three piece on the template. It should be noted that the last layer of chipboard should be 5 mm less than the other two.

Now with the help of sandpaper and a file, we process the corners of the preparation of podiums. That layer that was 5 mm less than the rest will actually be the top. After processing, the workpiece should be slightly rounded and narrowed in the upper part, which will give it more beauty and efficiency.

For greater reliability at this stage, you can additionally strengthen the chipboard layers by self-draws.

The time of the aesthetic part came, namely, the embelts of the workpiece. To do this, we need a small piece of carpet, which we convex future podiums. Again, it is advised to do everything extremely carefully and without any extra rush so that there are no folds and irregularities.

It remains only to cut the middle part of the carpet, set the speakers, attach our podiums on the door of the car and admire their beautiful views, as well as elegant sound.