Decorative niche of plasterboard under the TV: interior with their own hands. Plasterboard niches for televisions, choice and installation Beautiful niches under the TV

Modern TVs are not at all those "boxes" that had in every family 15-20 years ago. They became more elegant, thin and wide, with a high-quality image and multiple TV channels. So I want to spend the whole day next to a caring friend who will tell about all the news, drives to the exhibition, will demonstrate the actual film and will help become a member of an emotional talk show.

Which option to choose

In order for the time spent in a caring assistant's society, it was as comfortable as possible, experienced designers recommend not to fix the panel simply on one side of the room, but to make a niche for her.

Despite the fact that a small part of the room space will be occupied, this decision seems more profitable than to hollow out the surface and make a niche inside:

if this side of the hall is carrier, then on any work with it it is necessary to take a special permit in the municipal utility service, and it is not a fact that it will be issued;
if the house is brick, then special problems are not expected, but if you deal with concrete, then efforts will have to spend several times more;
the walls in homes are of different thickness, and if your design is assumed in a thin surface, then you will have to work carefully that instead of the desired project it turned out through an analogue.

There are plenty of different options for the device of cozy television alkalo, they can be divided into the following functional features:

design in the wall made exclusively under TV;
a variant in which part of the wall is involved, the shelves, fireplace and other elements can be turned on here, the benefit is double, since all shelves become part of a single complex, and they do not have to be attached to the surface separately;
the solution where the niche is an element of a complex beautiful design on the entire wall, there is also a lot of winning nuances.

In each of these cases, it is possible to take advantage of the ready-made features that the Internet, try to fantasize yourself or seek help from experienced designer. With any choice, your living room can be transformed for the better, adding aesthetic and functionality.

This maximally budget project, which will allow you to apply any of their three capabilities described above. Wherein:

it is necessary to choose a design where the panel will be completely inside, without protruding outside, so you will protect the costly household appliances from random contacts and save it in working condition;
here they can accommodate acoustic speakers, especially this advice is especially good for families with young children;
another advantage of such a kind of location of the objects is that cables and wire can be removed inside the complex, adding the total appearance of this side of the aesthetic living room;
the mounted lighting in this cozy for the eye Alcove will serve as an decoration of the room, will illuminate the necessary zone and create an additional effect.

Tip: If you approach the issue of creatively, you can not only save money, but also to create an interior that will create a feeling of expensive decoration.

Anyone, even a novice designer will advise to choose from three alternatives one that is most suitable for harmonious filling one of the sides of your living room, niche under the TV can be:

rectangular horizontal;
rectangular vertical;
oval.

However, there are no rigid design frames here, and within the same project, you can combine various versions.

Advantages of a rectangular horizontal option

As a rule, most of these designs are performed in a rectangular horizontal format. This solution allows you to make a full-fledged thin panel location and schedule a few more shelves to place some necessary items on them. A good supplement will be the highlighting. This project is welcomed by both large rooms and small living rooms, in the latter case it will be visually more spacious.

Uniqueness of a rectangular vertical project

If you want to try to experiment with a rectangular vertical format, the TV is advisable to stir around in the middle. All the rest of the space is filled with acoustic systems, books, paintings, coins for disks and other objects, logically complementary complex.

Rectangular niche - for wide walls

Plasterboard - excellent building material for the device of most interior parts, whether it is a fireplace or alcove. In our case, it is done in a curved form. This gives the effect of the entire hall. In addition, visually the upper part of the room increases. Experts believe that this project is not suitable for a living room with wide walls.

Oval alternative for large and small spaces

This is one of the least demanded projects, because it requires greater qualifications of the master due to difficulties in technology. Of course, it does not diminish, but, on the contrary, it advantageously emphasizes the uniqueness of the structure. Oval, at least more interesting any rectangle. If the room is small, then such a choice allows you to further narrow the space visually. However, for large living rooms with a high ceiling, such an alternative is suitable, as it is impossible to more by the way.

Materials required for the niche device do it yourself

What should be made to the list of materials to create alkalo under the TV, going to the building store:

do not do without aluminum profiles - CW (for fastening parts on the wall or ceiling) and UW (are carrier elements that lock plasterboard panels);
wood bar, the basis of the future project is created from it;
plasterboard panels are better to purchase 12,5 mm millimeter thickness, this is the most common building material;
elements of metal compounds, fastening profiles;
dowel and selflessness.

If you have to work with an oval solution, which assumes the arcuate elements, you should purchase a profile in the form of the arch, and the plasterboard should be selected such that it can be bent.

From tools for work should be taken:

screwdriver and screwdriver;
drill with revolutions change mode;
metal hacksaw;
a tool feeding from the network that can be processed profiles;
the plane, it will come in handy to cut and smooth out drywall panels;
construction knife;
roulette;
serpianka (this is a glasswall for reinforcing plasterboard parts after its installation on profiles);
plumbing and construction level;
lace.

Instead of the latter, you can use the usual rope.

Preparation for work

If you decide to work yourself, without the involvement of a specialist, it is important before starting work to draw the scheme of the future front of work, and the more it will be, the easier the process will go.

This applies to both the designations of all materials used and sizes, including the estimated dimensions of the TV:

special requirements for the correspondence of the depth of the opening with the thickness of the panel, if the socket is assumed for the TV, then this is additional calculations of the size (better if it is located at the bottom);
it is best to make an opening, which is greater than the plasma panel for 20 centimeters, such additional distances are required to elementary to cover the hand to configure and other functions;
it will be better if the drawing goes from the center of the surface, and so that there is no distortion, use the answer.

If there is no masked wires in the diagram, then in front of the device, extend the channel for them with a perforator, followed by a masking putty.

Phased design design

Installation and subsequent refinement of the project is simple, the main thing here is to comply with the priority of actions:

fixation of UD profiles with self-draws, it is done on the previously applied markup;
vertical installation in the UD profiles of CD profiles, it is better that the distance between the latter is 60 sorts, P-shaped attachments are welcome;
horizontal mounting of CD profiles on sides of the design;
when the frame is assembled, the tv-cable and electrical wiring laying (backlight);
plasterboard, in advance cut into parts according to the drawing made, attached to metal frame profiles;
the entire finished design is processed with a putty.

As you can see, there is nothing particularly difficult in this process. It is very important to prepare the scheme in advance, materials and tools - and then the construction of the niche will not take much time and will bring pleasure.

What you need to remember during the construction of the opening:

Your niche under tv is ready!

Construction of individual houses and apartments increases every year. Consequently, a person faces the problem of acquiring furniture in different ways for each room (kitchen, bedroom, living room, etc.). Furniture industry is a rather conservative system. Having mastered the technology of making a sofa or wall and putting certain funds of the host, hence it requires a refund with profit in terms of profitable for him.

Design and design of the gypsum wall under the TV

As a rule, the payback of capital investments is two years. To have individual furniture you need to apply. Interior designers received universal building material.

The design of furniture from drywall on a metallic frame will be functionally adapted to the installation of the TV with the necessary instrument. If you put a goal. Create a new room interior separated by this partition. In the decoration of the wall for the TV, you can use a tree and glass with various textures.

To create a wall of drywall under the TV, you must perform a design project. Specify the dimensions of the protruding parts and recesses.

Ready for trim Frame wall frame for TV

Measure radii and angles of curvilinear pieces of shelves. Prepare referents textures of plasterboard surfaces. Places of fastening profiles to the capital wall if necessary. By defining all the nodes in the project, proceed to the place of the future wall using the measuring instruments.
Necessary materials:

Required tools:

perforator Construction and special rolled for concrete, brick and wood;
or ;
screwdriver or drill;
and scissors or hacksaw for metal;
sandy paper for various purposes, spatula and.

Option Design Frame Plasterboard Wall under TV

Assembling the framework of metal structures is performed in several stages:

Saving framework

Works of HCL sheets start with the selection of the required fastener:

Hypotocarton Wall Sheet Process

Having the necessary sizes, on the elements of the wall facade. For savings, the cut-off lines on the sheet of large elements are pre-applied and then placed small parts between them. Making sure that the surface is used as much as possible, cut every detail with a knife or knife.

Hydroke Hypped Wall under TV

Phased process of manufacturing the wall under the TV from plasterboard

Ready elements from GLCs are cutting the frame. Sheets are fixed with screws with a puck to a frame, slightly bleak into the cardboard. Attasches are performed in a step between them 20-25 cm. After completing the cutting of the frame, the finishing of the finished wall is completed.

Finishing of the finished wall

The wall decoration is performed by several stages:

Construction finish.
Interior design of the wall under the TV.

Construction finish

On the joints to enhance the location of the sheets. External angular surfaces are enhanced by perforated corners. Ready and primed surfaces from drywall are equalized by plaque uniflot. Rights from the self-tapping screws, joints and mechanical damage are eliminated using a spatula.

The process of putting the wall of plasterboard walls

After drying the spacing of the surface of the wall for the TV is treated with a putty for the surface of multiphinish sheets. Aligning and dried by the shp can, the walls begin to decorative decoration.

Interior design of the wall under the TV

The wall under the TV cannot be the same and in the bedroom, and in the living room. Each room has interior design. If you do not change the interior of the room, the wall must be an integral part of the room.

An example of plasterboard walls under the interior of the room

If we consider that the plasterboard is a versatile material for using a different finish type, it is necessary to determine the style and color of the TV, as the wall for the TV, and not vice versa. Next, it is necessary to determine the lighting and local point illumination of various decorative elements, photos and indoor plants.

Registration walls in the living room

Deciding with the place of the TV in the interior it is necessary to prevent a number of elements that distract the viewer from viewing programs. The shelves should be with the doors, the color of the coatings is calm is not an allay, not saturated.

Options for design of plasterboard walls in the living room

Niche under the TV in the living room should be interesting. It is possible that the use of water-level paint, wallpaper, tissues and various and stucco. The main thing is that the wall does not conflict, but complemented the interior of the living room.

After finishing the wall, it is necessary to develop a light design of the entire living room. Install accent and for better perception in the night and evening beauty of the plasterboard walls for the TV.

Wall decorations in the bedroom

The interior design of the bedroom in principle does not differ from the design of the living room. Additionally, the age of residents of this room is taken into account. Conditionally disassemble the following categories:

If the living room must be universal for all ages, then in the bedroom it is necessary to fit individually to the resident of the room.

As a rule, the bedrooms design and build smaller sizes than the living room. And one side is used for window openings, and the other with the entrance door, as a consequence for the wall suitable smaller side of the bedroom.

Consequently, the plasterboard wall for the TV will be significantly less than in the living room and hall.

Options for making walls under the TV on the attic floor

Design a niche for the screen, bottom or side of the stereo cowle and near the disks and a video recorder or receiver satellite antenna. For decoration of the color scheme, it is desirable to use soft, pastel shades and unobtrusive light. In the LED bedrooms to use light in the format of point lamps, or garlands.

Options for lighting device in niche under TV

Tints of lighting is warm white. Cold white color gives sharp shadows. To illuminate the entire bedroom, use existing lamps and lamps. The video shows the process of assembling the wall under the TV.

Conducting repairs in the apartment, you need to think over all the details in advance. One of these parts is the availability of a TV. Someone hangs it on the wall, others use more traditional approaches. A niche made of drywall under the TV not only becomes part of the interior, but also greatly embellish it.

You can simply put the bedside table or hang it on the wall. Why cries your head with the creation of a huge design, providing for special niches in it? There are several reasons for this.

Niche is well hiding not only TV, but also columns, as well as wires. In this case, young children will not have access to them, and more beautiful.
When the cabinet is done under the TV from drywall, it seems cumbersome and alien in the room. In the case of a niche, the TV becomes part of the interior.
In the created niches, you can make hidden lighting, which will make the room more beautiful, and the evening time for the TV will become more pleasant.
Niche shelves can be used to accommodate other items (books, discs, etc.).

In what style to make everything

Different ideas and options for designing a niche from drywall under TV are a huge set. Before you begin work, you need to decide with your desires. Someone uses the design to zoning the room, others choose the smallest wall so that everything looks compact. There are three main options forms of the niche:

the design can be made in the form of a horizontal rectangle. This option is good for large walls and looks wonderful;
making a niche in the form of a rectangle of the vertical form is rationally not only in small rooms, but also in large. Such a portal of plasterboard for the TV is placed from the floor to the ceiling. Sometimes it smoothly flows into the ceiling, but it is already difficult to fulfill without the help of professionals. Usually this option is used in long rooms;
oval niche for a TV from drywall is the option to which the Matters are resorted. It looks very beautiful, just to make it extremely difficult.

Round or oval niche under the TV make it more difficult, but for professionals it is not an obstacle!

It does not end in the choice of design form, because it consists of a variety of elements. There is a lot of ways to make such a niche for a TV unique, and it is not only about how profiles with plasterboard can be used. Lighting plays a huge role.

Spotlights are usually installed in a row horizontally either vertically. Lamps can be installed under the TV. They can also go on its sides of the floor to the ceiling;
Used diode backlight. Often, such a backlight is taking closer to the ceiling or around the speaker system.
A niche of drywall under a TV with lighting with LED lamps will be the best option. Such lamps do not emit heat and do not overheat.
Often the backlight is made hidden so that the lighting is not aggressive. Not very nice to watch TV when the light beats into the eyes.

Backlight is better placed closer to the ceiling.

Tools and components

Deciding with the place, sizes and shape of the future niche from plasterboard for the TV, is the time to get the necessary tools and consumables. The following materials will be required for work:

wall plasterboard with a thickness of 12.5 mm. Its width is 1.2 meters, and the length is usually 2.5 or 3 meters;
self-tapping screws for fastening of plasterboard;
profiles for creating a frame. Some profiles will be guided, while others are rapidly. The latter are used when creating carrier elements;
dowels for fastening profiles to the wall and floor.

Also, the plasterboard wall under the TV can be constructed using wooden bars that will enhance the entire design.

Wooden bars are often used as mortgages to mount brackets for TV to them. In this case, the TV is hanging on the wall and is fixed reliably, thanks to the mortgage.

In addition to consumables, you will need tools without which you can forget about the quality of work performed.

With the help of a drill, drill the wall and profiles for reliable frame fixation.
The screw is quickly screwed up the screws, but you can do with a curly screwdriver. Screw the screws with hands longer and harder, but cheaper.
Profile need to cut something. For these purposes, Bulgarian is suitable, metal scissors and a metal knife.
Without level (water or laser), you can forget about creating smooth surfaces.
Roulette, pencil, ruler, chopping cord, all this will be required for surface markup.
The construction knife is useful not only for cutting drywall, but also to remove the chamfer.

Preparatory work - we take into account everything

Any sketch will simplify work

Fasteners and tools are not the only one that should be taken care of how to make a niche of drywall under the TV. You will still need to carry out calculations, create a project, draw a sketch and mark up.

The TV must already be purchased, because we need its size. It does not matter whether there will be a TV hang onto the wall or installed on the shelf, it is necessary to know its dimensions to leave the desired space. If the plasma will hang on the wall, then it is necessary to know the size of the bracket to lay down the mortgages.

The place is also selected under the column, the game console DVD player and other devices that can be used. All this needs to be calculated so that it can be in a niche. In addition, it is necessary to leave a stock of the space of 10 cm on each side.

Not only width and height are important, and the depth should also be taken into account. It will come out very ugly, if something is writhe. Even worse, if the niches are too deep, as a result of which the useful space of the room will be spent in vain.

Sketch and drawing of the future niche from drywall under TV will greatly facilitate work

The design sketch will not only help itself imagine everything, but also to sketch the primary action plan. The design of plasterboard on the TV wall is created much easier if there is a sketch. Even the simplest drawing will allow to imagine where and how profiles will be installed, as well as how many plasterboard will be required. Due to the sketch, it is much easier to mark on the wall of the frame.

Marking always arise difficulties and many prefer to collect frames in place, and whether be it, what will happen. This approach is not particularly good for those who want to get a qualitatively made niche from drywall under TV.

With the level, ruler and plumbing are the extreme points of the design, which will perform from the wall as much as possible. All the same tools will help spend on the walls, floor and ceiling line, which will denote the front boundary of the collected design.

In the same way, a rectangle draws on the wall denoting the place of the central niche. If there are still some niches and shelves, they are drawn in the same way on the wall.

Frame assembly - step-by-step instruction

Cut up to the desired size all profiles. Typically take guides 27 * 28 mm. They are attached to the surface, as well as used as jumpers. The rack profiles 60 * 27 mm are needed to create a carrier frame. Note that the size of the profiles is chosen so that they are combined with each other.
On all marked surfaces (both vertically and horizontally), a guide profile on a dowel is attached (40 cm mounting step). Also, the guides are attached on the floor and the ceiling (if the selected form of construction requires). On the floor, the profile is attached perpendicular to the wall and vertically installed guide. Similarly are made on the ceiling.
There are still guides between the profiles on the floor. If necessary, it is similar to the ceiling. A niche for a tv from plasterboard implies a deepening, which is created by such installation profiles.
Insert the rack profile in all areas where it is necessary on the sketch.
Between the racks are mounted jumpers from the guides, which will serve as the upper and lower part of the niche created. These jumpers must be parallel to the horizontal guide, which was installed on the floor.
Between the jumpers and lower guides, the rack profile is installed vertically. This is how a kind of drywall is created under the TV.
If necessary, the design can be reinforced with additional jumpers. Usually they are installed for the plane to which the TV will be put.

When building a frame of a niche, it is important to strengthen those places where the greatest load is supposed.

All profiles between themselves must be connected with the help of the "bugs". These are such small tapes for metal. You can also use the rod, but not everyone knows how to choose it correctly and work with it.

All jumpers niche for the TV must be fixed with self-drawers, as additional load will be performed on them.

Cracking frame plasterboard

All HCL sheets will need to be cut to the size of the design. First, the largest elements are trimmed, and then those that are in bed. Also, first need to sow external structural elements, and then internal.

The sliced \u200b\u200bsheet of drywall is applied to the design and is attached to the self-tapping screw. Work begins from any edge and goes from it in the selected side. You can not fasten the leaf at the top, then below and only then begin to screw it in the center. Then a niche of drywall under the TV can get a little convex. It may be imperceptible to the eye, but you will always remember this defect. Therefore, the sheets are attached consistently from one edge to another, so that they smash in the process.

Self-tapping screws across every 15 cm in all places where GLCs are in contact with the profile. It is necessary to screw them as much as possible to the center of the profile so that the hat is deeply deepened into the plasterboard.

Plasterboard is attached so that it reaches exactly the edge of the profile and did not speak for it. However, when the sheets are attached at right angles, there should be no gaps between them. Ultimately, profiles should not be visible, only plasterboard.

The shelf under the TV from drywall should be strong enough. Therefore, under it is done not only the reinforced frame with jumpers, but also sometimes weave the plasterboard in two layers. This is done only with the part of the design on which TV will be. Then you can be sure that all design elements will withstand possible loads.

When covering GCC, all the nuances with backlit, sockets and wires are taken into account. In certain places it will be necessary to do the openings for wiring.

Original niche asymmetric form under the TV

Finish finish

I would not want to stop at this stage of the work, because everyone should decide for himself than to bind the designed design. However, there are certain details for which it is necessary to pay attention to:

shakes, except angular, undesirable. Therefore, it is necessary that each part of the design being created was solid sheet. The presence of direct bogs of drywall can lead to the appearance of cracks in the future. To avoid this to be avoided, use the reinforcing tape and the proper technique of spatleing joints;
all angular joints must be protected using a reinforcing corner (there are plastic and metallic); Corners are placed on putty;
created from drywall niche under the TV is processed by a completely starting putty;
the dried starting putty is treated with sandpaper, ground, and then they apply a thin layer of finishing putty;
the truncated layer of finish putty is treated at wisdom.

You can learn about creating more complex designs from the video.

In a modern designer approach, it is fashionable to hide household appliances in a niche of plasterboard, leaving only the facade of technology. A niche for a TV from plasterboard is made simply and quickly.

Once upon a time, the TV was standing on a stool or a wooden bedside table, then on a special end, now he is suspended on the wall, hide in a niche.

An example of a multi-level drywall niche under TV

niche must be located opposite the bed;
she must fit into the interior;
for greater convenience.

When solving all questions you can start.

Design and design niche under the TV in the room

Profile. It is advisable to take galvanized with ribs of rigidity.
GLC up to 12 mm thick.
For fasteners in the wall.
Connectors for profiles.
With a set of blades.
Screwdriver Set.
Passatia.
Perhaps you need a hammer.
Hoven, spatula ,.
Anti-grapple primer.
Wires, switches, connectors.
Protective sleeve.
Roulette or meter.
Pencil, marker.
Water or laser level.
Grout - sandpaper or special mesh.

And also need clean water, first aid kit.

Technology for creating a design under TV with step-by-step instructions

Niches are different:

Curvilinear structures;
Square and rectangular;
Additional departments for audio, video systems;
With illumination and without it.

If the TV is heavy, then the frame should be strengthened with wooden partitions. A niche for a plasterboard TV is also open (open side parties), built-in (TV is hiding completely, only the facade is visible). It should be decisled which niche will begin to draw a sketch.

Drawings and calculations

Taketing for the drawing, you must think carefully to the smallest detail. Because of small omissions, it may not be design.

Drawing with dimensions for mounting niche from drywall under TV

Taking a sheet of paper to draw each line, put each point and write down all the sizes and numbers obtained during the calculations. The dimensions of the TV should be taken into account so that the niche does not turn out. Leave a place to ventilation of equipment.
You should draw wiring and places of lamps. This is important because during the installation of the frame, and not after the complete installation of the structure.
It follows in the drawing to designate the location of the switch and sockets.

Preparation for assembling construction of metal products

Before, you should clean the wall (if it is not pissed and painted). Check the wall cover for the presence of depressions and protrusions.

Metal Frame Frame Design

If such are present, use the putty and bring the surface to smooth if there are bugars, they must be cleaned. In some cases. When the surface is prepared, the paper drawing is transferred to the wall, observing all the sizes.

For the convenience of applying wall covering, you can share equally, designating the external dimensions of the niche for the TV.

By setting all the points and drawing a sleeve shutter path with wires. In some cases, the wires should be hidden in the wall. To do this, stamp the channels of the wiring channel, fix them there and close the canal with putty. Wait for her drying.

Assembling metal carcass

Assembling the carcass under the TV with your own hands has features. In addition to the main installation of the frame, in the design there are curvilinear forms that serve only for decor.
Mounting the frame starts with the drawn lines. The size of the profiles must be no more than 5 cm. Gearing niche 7 cm depending on the design of the niche, 4 guide profiles should be on a wall basis. If the wall from the drywall is already ready, it must be enhanced with wood or horizontal crossbars every 5 cm.

At the bottom of the box for the TV, a "podium" is needed, protruding for the facade of the design. The height of the "Podium" is 10 cm. It serves to adjust the installation of the floor plinth. If the plasterboard niches goes up to the ceiling itself, then such an indentation from the ceiling should also be made.

Sketch of a niche of plasterboard under the TV

In order to require the same guide profile, as on the wall. Between the guide profiles (NP) jumpers are inserted, the length of which is equal to the depth of the niche.

The curved side face is made curved NP. On the wall, the curved line is fixed along the line, the remaining curved lines are made using a plasterboard template. The curvilinear profiles are attached to the standard method. The place between the colonams determines the niche for the shelf under the TV. The frame for the shelf is assembled by the standard way, the only thing when the shelf is "recessed" in a niche, it should be supported by vertical racks.

Cleaning and finishing niche

In the trim there is no specification separate from other works. , as in other structures.

Options for finishing niche under TV

After placing with plasterboard, it follows at the corners and borders to apply the strengthening of fiberglass. After or, the masters and designers strongly recommend the shelf to cover with thin glass. The video shows the step-by-step assembly process and finishing a niche from drywall under the TV.

Registration

After installing and extinguishing the frame, the lighting devices are proceeded. In addition, many masters use more practical and durable LED tape. With it, you can make not only muted illumination, but also combine colors. A niche for a tv from plasterboard with such illumination will make the interior of the room more interesting and more comfortable.

Point lamps can be positioned above the additional shelves, where, let's say, there are columns or discs.

Interestingly, the backlight will look at the bottom up - the lighting devices are located at the bottom. There are different ideas for the installation of lighting devices that create harmony of light.

Options for design and design niche under TV with LED backlight

A niche of plasterboard for the TV should be painted with a light tone (the wallpaper should be lighter by shade than the main). An interesting design version is a stone niche finish, but this is if there is a niche under the room, which is decorated in the same way. The peculiarity of this decoration is to give the interior of naturalness and rigor. In a number of designer decisions, an angular niche for a small TV is made in a small room.

A niche for a TV from plasterboard with its own hands is a great installation option for modern household appliances. Plasterboard sheets are practical, universal material, which will help create a design quickly and without special costs.

Plasterboard niche for TV: benefits

If you have never dealt with this material and doubt whether it will suit your home appliances, we suggest familiarizing yourself with the main advantages of this design:

The TV will perfectly fit into any concept of the interior, will not seem to be a "outsider" subject
The design will allow you to place not only TV, but also other items - discs, books, various decorative elements
TV will be protected from falling and mechanical damage
You can completely hide the wires and cables - the interior will look more aesthetic
Luminaires are placed in the resulting recess, which will make the space lighter and cozy
Design installation requires minimal financial costs.

Varieties of form

The most popular form of a plasterboard niche for TVs is rectangular. However, this is not the only design option. If you like the original solutions, we recommend that you pay attention to other options.

Rectangular shape

It allows you to perfectly fit a thin screen, as well as equip additional shelves. This is an excellent solution for placing any size. The recess can be located both vertically and horizontally. Vertical niche increases the space above the head, so it is perfect for too wide walls.

Oval form

Due to the complex manufacturing technology, it is rarely used to install televisions. However, it will certainly like the lovers of original solutions. The design visually reduces the space, so it is necessary to use it in the interior very carefully.

Curved shape

Just as oval, manufactured by complex technology, but it looks original and stylish.

Jpg "alt \u003d" (! Lang: niche under a tv from drywall do it yourself" width="795" height="530" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/10/post_201_3794..jpg 300w" sizes="(max-width: 795px) 100vw, 795px">!}
.jpg "alt \u003d" (! Lang: Niche under a TV from drywall do it yourself" width="795" height="551" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/10/post_201_3791..jpg 300w" sizes="(max-width: 795px) 100vw, 795px">!}
.jpg "alt \u003d" (! Lang: Niche under a TV from drywall do it yourself" width="795" height="544" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/10/post_201_3789..jpg 300w" sizes="(max-width: 795px) 100vw, 795px">!}
.jpg "alt \u003d" (! Lang: Niche under a TV from drywall do it yourself" width="795" height="528" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/10/top_201..jpg 300w" sizes="(max-width: 795px) 100vw, 795px">!}
.jpg "alt \u003d" (! Lang: Niche under a TV from drywall do it yourself" width="795" height="546" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/10/post_201_3797..jpg 300w" sizes="(max-width: 795px) 100vw, 795px">!}
.jpg "alt \u003d" (! Lang: Niche under a TV from drywall do it yourself" width="795" height="527" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/10/post_201_3796..jpg 300w" sizes="(max-width: 795px) 100vw, 795px">!}

Design options

The deepening takes upon itself not only the functional load, but is an excellent decorative element, so the designers have developed several options for its design.

In the form of a box

This is a decorative design with open shelves and different racks.

Niche on a smooth wall

Here can also be boxes, lockers. It turns out a peculiar wall of plasterboard under the TV.

Additional shelves and racks can also be located differently:

Asymmetric

This location is suitable for ergonomic use of space. Suitable for zoned and combined rooms.

Symmetric

Symmetric niche perfectly fit into the interior, furnished in a classic style. You can thus find a TV in rooms intended for rest and sleep.

A niche of a plasterboard with backlit for the TV is also extremely popular. The backlight can serve not only with a decor, but also a separate light source.

Sketch development

This is an important stage of creating a design of drywall under the TV. The more detailed you all think over, the less likelihood that work will need to redo.

The basis of the sketch is the drawn frame of the future niche. Here it is necessary to portrait all verticals and horizontals, consider the location of all carrier profiles, take into account the load on them, etc.;
An image of changes in electrical wiring. Location of plasterboard sheets. Drawing the main lines of structures;
The placement of finishing materials, the accounting of their thickness, the effect on the general type of construction.

To calculate the correct, follow the following recommendations:

The depth of the design should coincide with the length of the TV so that it does not speak for the edges of the plasterboard sheets. If a socket is located behind the TV, you need to increase the depth several times
The width of the shelf must be 20 cm more than the TV. On the sides you also need to leave a small distance to be convenient to connect and disable the technique

All other sizes can be monitored at its own discretion.

Required tools and materials

Any installation work suggests those or other tools and materials, without which it is impossible to perform it quickly and efficiently. For the construction of a high-quality niche of drywall in the living room under the TV, prepare:

Metal profiles. They will be needed for the construction of a rigid frame - the foundations of the future niche or shelves from drywall under the TV. For any form you will need 2 rack and 2 guide profiles. If the design design is curved, the arched profile will be needed.
Plasterboard sheets. This is the main material to create a deepening. To fix them, you need to prepare special screws
Dowel. These are special fasteners that allow firmly fixing the guide profiles. They are ideal for fastening a metal frame to concrete and brick walls.
Decoration Materials. Any plasterboard design involves the use of compositions for alignment and processing. To this end, it is worth getting a putty and primer. To give a niche of a beautiful, aesthetic type, tile, wallpaper, mosaic, paint, etc. are used.
Instruments. To work with metal profiles and plasterboard sheets, you need to get: drill, screwdriver, screwdriver, hacksaw, branches, construction knife, measurement devices

The block of sockets is usually located below. Wires will be hidden behind the TV.

How to make a niche of drywall under the TV: workflow

Main steps:

Data-Lazy-Type \u003d "image" data-src \u003d "https://remontcap.ru/wp-contective/uploads/2017/10/a303b74c46c9217fc17198fc13cdb0da.jpg" alt \u003d "(! Lang: Niche under a tv from drywall do it yourself" width="718" height="415" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/10/a303b74c46c9217fc17198fc13cdb0da..jpg 300w" sizes="(max-width: 718px) 100vw, 718px">!}

Jpg "alt \u003d" (! Lang: niche under a tv from drywall do it yourself" width="800" height="450" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/10/maxresdefault-5..jpg 300w" sizes="(max-width: 800px) 100vw, 800px">!}

What finish to choose?

Paint

This option of trimming by plasterboard niche under the TV is suitable if the putty is applied neatly and efficiently. To give the surface of the invoice, use a special spatula to apply paint.

Wallpaper

This is the cheapest and simple finish option. For the severity of the niche and the whole wall, you can use the same wallpapers. Niche will be absolutely invisible.

Fake diamond

Such a finish will take a lot of time and will require maximum effort. The material can be cut into a grinder if necessary. It is convenient to use liquid nails with an artificial stone.

Polyurethane

Foamed plastic is an excellent modern material for finishing. From it you can create a variety of patterns and textures. It is perfect for the decor of the classic-style rooms.

A TV in a niche of plasterboard on the wall will update your interior, make it interesting and original. If you want to "refresh" the room, be sure to consider this option.