Stand for charging the phone with your own hands. Stands under the phone: Best ideas. From the designer Lego.

Mobile phones tightly entered our daily life. Even children are already using them from the very first school classes. In order not to throw your gadget simply on the table, consider how to make a stand for a phone from girlfriend.

First option: from binders

We will analyze how to make a stand for your own hands from what is practically in every home. There are quite a lot of ways. In this master class, we will produce it from the binders (clamps for securities).

Such a model is well suited for widescreen phones. It will be very comfortable and practical, and the creation will take literally two minutes.

Binders and suction cup will be required for work.

Production Procedure:

Connect the binder with the suction cup (the holder for towels is suitable) in the place where the hook is located.
At this suction cup attach the rear panel of the phone when you need to put it, and everything is ready.

The advantage of this kind is that the phone can be positioned in any position, both horizontally and vertically, or at an angle.

Second version: paper

When there are many pieces of paper on different colors, then technique of modular origami comes to mind. We will analyze how to make a phone stand from paper.

It will take 24 white ticks and 23 pink. Tick \u200b\u200bis the easiest element of modular origami.

To make modules, do the following:

The triangular module consists of rectangles so that they turn out the same size, take the A4 sheet and cut it into 16 or 32 small rectangles.
Bend the rectangle in half.
And once again in half, then break the fold of the fold in the middle.
To this line, remove the edges of the rectangle, and those where the first fold line goes.
From the bottom you have formed a protrusion, the corners of it bend up to the edge of the first part.
Now everything remaining the bottom canvas bend up to get a smooth triangle on the reverse side.
Fold it in half. And you will see that you got pockets from two sides.

Now go to our question how to make a stand for a phone from such modules:

While white ticks in a circle.
Then place the pink between each pair. So you will get a tough cone.
Continue collection to the desired height, and everything is ready.

This method is suitable for lovers to work with paper in the technique of modular origami, if you like to cut everything more and stick, then pay attention to the following model.

Third option: from a bottle of shampoo

How to make a stand for your own hands from a bottle of shampoo? The work will work very stylish, despite simple materials, it will look expensive, as if purchased.

Manufacturement:

Choose a suitable bottle of shampoo.
Make in the middle line and cut down on it. For convenience, it is better to do not directly do, but on the back side, leave the ledge with the slot so that you can not only install a stand on the table, but also hang on the wall.
Take a beautiful paper with an ornament (you can use the wrapping), wrap it with a stand and glue.
Carefully cut down the excess wrapper along the contour. Your work is ready.

This handicraft will look great in your home, especially if you correctly pick up the color and drawing of the wrapping paper. You can independently come up with a form for such a job or make a sample. It was one of many ways to make a stand under the phone.

Fourth option: from sticks from popsicle

One of the most original options, how to make a stand for a phone is to use sticks from the ice cream "Eskimo". For this, in advance, ask friends and relatives not to throw out such wands.

When you get enough, they will need to glue:

initially, make the bottom;
then the back back on the height of the phone;
side will look good at the tilt.

You can connect the details not only by glue, but also sinking the transverse stick for a greater fortress.

There are many ways how to make a stand for a phone from girlfriend. We looked at only a few of them. It all depends on your mood and fantasy. Even from the old "Lego" designer, you can make a wonderful cover on the wall out of the tight fabric.

Use any idea. Enjoy your creativity!

As often, being at home, in the office or on the road, we cannot remember where they put our phone. So that this does not happen, you should get comfortable and ergonomic stands that can be made independently. The stand for the phone can be made with your own hands from the most unexpected girlfriends. How to do this, will tell our step-by-step master class.

How to make a stand for your own hands: Options for office and auto

Being in the workplace or in a car, we all need to always be in touch. At the same time, I do not want to spend a lot of money on expensive stands, because they can be made from the cast and served their terms.

Stand from the card.

The easiest option of the telephone holder is a stand from the card. To make it, it is necessary to gently bend an unnecessary plastic card in two places, as shown in the photo below, not allowing it to break.

Experience shows that the plastic card stand is very reliable and withstands even the airline at the moment of severe turbulence.

Stand from stationery clamps.

For the manufacture of a stand for a phone from stationery clamps or from binders, as they are also called, one big and one small clamp will be required. The legs of the small clamp should be placed between the holding part of the large clamp and put the resulting design on the table so that the larger clamp relieves on its surface.

Similar supports can be made in five minutes from clothespins for linen.

From paper clips, a great version of the stand for cars is obtained. For its manufacture, it is necessary to disassemble the clip of a large size and slightly bend the metal parts, as shown in the photo below.

In order not to damage the surface of the phone, metal fastenings are recommended to wind into several layers. We return holders to the place, additionally fasten them with a sticky ribbon and stationery. Breeping clamp on ventilation blinds. The phone is securely attached between the metal parts of the binder.

Paper stand.

The usual office paper, folded in a certain way, can withstand even the weight of a large smartphone. To make a paper stand, you need to measure the size of the phone and adjust the pattern below.

Cut the part of the paper, fold it on dotted lines and insert the side parts in the slot. This design is good because it allows you to charge the phone without removing it from the stand.

We study the popular options for home coats

The desktop stand for the house should be not only convenient, but also durable, stylish and well fit into the interior of the dwelling. Consider options for such products.

Stand from newspaper tubes.

The stand for the phone from newspaper tubes will become a wonderful gift and an excellent decoration of any interior.

To rinse such a stand, you will need a few colored in advance of long newspaper tubes, scissors, knitting needles, some glue and varnish.

Six blanks, we have parallel to each other at a distance of approximately 1-1.5 cm and firmly fix them in the machine or in any convenient way. In extreme raskirts, we lay the needles or wire to make it easier to form smooth and neat contours of the product. We begin to told the base of the working tube in the "Rope" technique or a terminal weaving. Follow the parallelism of the rows and, if necessary, we rinse them with glue for better fixation.

We ride a rectangular workpiece required length. Take out the needles or wire. The tips of the racks accurately refuel and cut. Give the workpiece the necessary curved shape, if necessary, a slightly wetting it with water.

Similarly, we ride the leg of the stand on a smaller number of tubes. Introducing the finished leg, install on the main part and fix its stores between the rows of the stand. Superior cut and hide. We wash the product with glue, if you wish, additionally stain and cover 1-2 layers of varnish. After complete drying, the stand can be used for its intended purpose.

Stand from Origami modules.

Modular origami is a fairly young, but very popular view of the needlework. With it, you can make many unusual and original things, including a stand for a phone from modules.

For the manufacture of the stand, two-sided paper of blue and pink color will be required. Cut the sheets on the workpiece and fold the modules.

Weaving start with the base of the stand. It will take 28 blue modules to be needed to be combined with each other and closer to the ring. Similarly, we make another three rows. From the fifth row, we reduce the number of modules per 1, 2, 3, 4 pieces. In the seventh row we put one pink module in the middle.

In the eighth row, we put 6 modules, make a pass, 10 more modules, skip, 6 modules. The number of pink modules - 2 pieces. In the next row on the pink plot, we put three pink modules. We begin to make a curly edge of the stand, as shown in the photo below.

In the back we form a pattern in the form of a heart, over which we install a row of blue modules. We gradually narrow the stand since the triangular wedge is not formed in its back.

Stand from modules is ready!

Video on the topic

We offer to see the following video lessons on the manufacture of other supports under the phone.

Mobile phone has become an unchanged attribute of a modern person. Both on the road, and at home, and on the desktop, the main place is given the main place, and "suddenly someone will call, but I will not hear / see." For convenient placement of the cellular on the table, the stand was invented. You can buy them in the store, but you can make with your own hands from the girlfriend. In the work, even the most useless at first glance "unnecessary garbage", like a cardboard package from dairy products or a long-used disc cover.

Stand from cardboard

The first option is the manufacture of a stand for mobile cardboard. This is not necessarily a solid piece of material, you can take the used milk package of a small volume (0.5 ml). It does not need to glue anything: only scissors will need.

The box must be thoroughly wash, smat and cut off the bottom. Then cut it along folds.

In the paper it will take the central part in the form of two rectangles. Between them - fold. It needs to be cut and folded the outside inside, clamping the bending place with one hand.

Starting from the opposite end, below, it is necessary to cut the figure, reminiscent of the letter "T". It is narrowed up, but has an awesome corner.

When the figure is in the deployed form, the lower edges become a place where the phone is located. He rests on the central face. The budget stand is ready!

Cover Stand for Disk

Surely, a couple of other DVDs fell in the house in the house. One of the unnecessary covers can be turned into a platform support.

For this, the cover must be cut in half. Then crop all the holes and rivets so that only a smooth rectangle with two bent corners at the ends remains.

The plate must be clamped with a tweezers or passage and omit in boiling water. Thus, plastic will become soft and pliable.

Holding the plate with the help of the passage or any other tool, it must be bent so that one of the corners ends a little reached the other. It is enough 2-3 cm, on this space and a telephone will be located. One of the corners is glued to the surface. It turned out an interesting and lightweight stand. The device can be located on it both vertically and horizontally!

Stand from a clip

Stand for a mobility from a clip is an interesting thing that can be done in 2 minutes. To do this, you need a large massive paper clip that you just need to disperse correctly!

To start the wire, it is completely straightened into the line. Then you need to hold it and rejected it:

Bend in the shape of a check mark - U.
Both End bend at an angle of 90 ° C, starting approximately middle.
Slightly bend horses of each end.

Thus, the ordinary clip has turned into a laconic stand. The phone lies horizontally.

Toilet paper sleeve stand

Such a good, like a sleeve from the used roll of toilet paper, grabs in every home! Do not rush to throw out the cardboard shape - it can be turned into a stand for mobile in minutes.

All that is required is to correctly cut part of the sleeve at an angle. The front should be a small part of the cardboard to create an emphasis. On such a stand will not be able to accommodate too high the phone, but the standard size "sees" perfectly.

If you wish, the stand can be decorated: coloring, wrap the cloth or enclose paper for gifts. And no one believes that once she was part of the toilet roll.

All work step by step

Output:

In working with the usual things it is important to give the will of fantasy: trying to think, experiment. Then supports for mobile phones will appear in the house regularly - and always different and interesting!

Modern communications are performed by many functions, so it is often necessary to install a gadget on the desk. The easiest way to purchase a ready-made device in the nearest store, but you can make it yourself. There are many ways to make a stand for a phone from girlfriend and stationery.

From the stationery binders

Students and office workers are familiar with special clips for bulk pile of papers, which are called binders. If the holders are the easiest way to make a stand for your own hands from them.

To do this, it is enough to connect 2 elements among themselves, and 1 metal end to exacerbate towards the phone.

You can also bind 2 bindel by a piece of cardboard, and the smartphone insert into the plane between the metal ears. Despite small sizes, such a device can even keep the phone with a large screen diagonal of both vertically and horizontally.

From the designer Lego.

If children live in the house, it will definitely find a plastic constructor with details of different sizes and colors. There are no special instructions for the manufacture of the stand under the phone, it is only necessary to select suitable items and connect them in any order. The main thing is that the design is stable and attractive.

From the stationery clips

Of many ways, how to make the delivery for the smartphone, the fastest and simple is the one in which the simple stationery clip of the large size is used.

To make the device, you must first break the clip into the straight line. Then bend again so that the average part creates a support for the rear wall, and the edges in the form of hooks did not give the phone to slip forward.

From wire hanger

If there is a wire hanger for clothes, you can make an original stand for a smartphone or tablet. For work, only pliers and some patience will be required:

First you need to bend both edges of the hanger so that they are located apart from each other at a distance equal to the width of the gadget. The edges are compressed by pliers until a complete connection.
At each end, there are 2 bends of about 3-4 cm.
At the next stage, the hook is rejected at an angle of 90 ° and rotate in the direction of the wings.
Then at the end of the top items make a hook for which the inner element of the hangers is cling and fixed.

The design can be improved by rubber tubes that will ensure the anti-slip effect and give the product a greater attraction.

Shampoo bottle option

An empty bottle of shampoo can turn into a comfortable and beautiful stand for the phone. The advantage of such a device is that it can be suspended on the power supply unit of the charger and eliminate the risk to hook the wires and drop the gadget to the floor.

For the manufacture of the holder, you will need a plastic container of the required size, a marker and a stationery knife. First, on the bottle make the markup of future places of the cuts, given the depth of the phone, the location of the holes for plugs and the dimensions of the power supply. After the layout is thoroughly drawn, all lines are cut with a knife, and the edges are cleaned. If everything is done correctly, the holder can be easily applied to the charger fork and stick it into the outlet. The gadget itself will fit freely in the bowl, eliminating the bending of the wires.

So that the device looks more attractive, its surface can be saved with a cloth or bright paper, paint the color suitable for plastic. The advantage of such a stand is its low cost, since the material is used for discarding. In addition, a wide selection of color gamut and containers sizes are available.

Option of chopsticks

Do not hurry to throw away sticks from the pop. Of these, you can also make a beautiful stand for your phone. Depending on the project, the design consists of several elements or includes a dozen components. Blood wands can be pvs or a glue gun. After the holder is ready, it is recommended to paint or cover it with varnish.

From paper

One of the most common materials that is used for the manufacture of a stand for a smartphone with your own hands is paper or cardboard. With proper design it will turn out a fairly strong product.

The easiest way to create 2 triangular lumps of different sizes. One will serve as the basis, the other - support for the bottom end of the phone. After the workpiece is completely dried, they are fixed on 1 paper rectangle.

Mobile communications, there are in every home, they have become practically indispensable for a modern person and perform a lot of functions. Therefore, quite often they need to keep not in your pocket, but on the desktop, so the stand under the smartphone is necessary for everyone. There are many ways to make a stand for a phone, but one of the best options is a tree of course, as it, despite its hardness, does not scratch the smartphone and it will look good both in the office and at home on the table.

The easiest way to make a stand for the phone with your own hands from a tree is just to make it from the usual way. The design of such a product is as simple as possible - the groove is made in the board of the desired width and the stand is ready. Since the table has a big plane, and after you put a mobile one in the slot, it will be firmly and reliably standing on the table.

The most important thing in this stand for the phone from the tree is the base area that will touch the table, it must be large enough to cope with the functional load. As a basis, such a homemade stand for the phone can have any wood and it can be given any forms. And the manufacturing process itself is limited by the fact that in the table with a milling mill, the groove is simply made. The grooves can be done smooth or under a slope, depending on how the device should stand.

When you make a stand for a smartphone with your own hands, it is important to polish it well, especially in the area of \u200b\u200bthe groove where mobile will stand. After all, if there are irregularities, then you can scratch the glass, and this will spoil the appearance of your gadget.

Complex design

If you want your mobile device to be always in sight, not lost in the documents and at the same time your table looked beautiful, solid, then the stand must be appropriate. To do this, you can make it not just from the plank, but from several details. You can, do not worry for this, too, do not need a lot of tools or material. The most important thing is not to rush and thoroughly consider the design that your homemade will have.

A good stand for a smartphone with their own hands, which will not only suit any phone, but also for the tablet, and at the same time will be as stable as possible, you can make two small does.

The design of such a stand is as simple as possible, two identical wooden billets of rectangular shape are taken. On the one hand, approximately, a quarter from the edge is made a slot to the middle of the board. It is important that the slot goes not at a right angle, but an imagination that the stand is more stable, and had the right slope of the plane that will support the phone. On both billets, the slot is made to half the width of the workpiece.

For someone who is just starting to work, can be problematic to choose the right corner for the slot. But it is easy to do it, it is enough just to attach two details one to another under the planned angle and just make the mark on the side at the end. Well, in addition, that the phone does not slip out, you need to make a groove on the horizontal plank, or stick a small bar, which will be a stopper.

After all the slots are ready, it is enough to finely polish the stand so that the irregularities do not scratch the phone body, and cover it with tinting or just varnish.

There are many ways to make a stand under the phone of such a design, for example, you can make a curly vertical part of the stand, which will significantly improve its appearance. Forms can be a wide variety of hand, leaf, animals and in general everything you think of, as a tree can be given almost any shape.

How to choose a stand design

There are quite a few ways to make a stand for a smartphone, but vessels from wood are different not only in durability, and a beautiful view. In addition, they look and much noble than other materials, since the properly chopped wooden accessory will decorate any design regardless of its style.

Therefore, so that your stand for a mobile phone made with your own hands was beautiful and original, try to choose to choose the design, size and color. Of course, you should not forget about such parameters as functionality and stability, since the cellter may simply be damaged.

You can make a variety of accessories for the phone at home and for this it is not necessary to have a special tool. In most cases, it is possible with due diligence and patience to do with a simple hacksaw, a chisel, a skirt and a piece of plywood. Then just glue your sample from small parts and at home this will also be easy.

Do not be afraid to experiment and dream so that the stand you make is unique, and not like everyone else. After all, mass production has been established in such a way that anyone can afford to buy beautiful and the first kind of a variety of things. But truly bright individuality prefers unique things in a single copy. Such things in stores are not sold, they can only book or do it yourself. The second option is much better, not only in terms of savings, but also in terms of manifestation of individuality.

Even if you have no experience in the manufacture of any crafts from the tree, do not be upset, because there is nothing complicated. It is quite carefully planned to plan, calculate what instruments will need, materials and only after that begin to work itself. If you can't do something, then you can try again, it is rare who it turns out to do everything right from the first time, everyone learn and all make mistakes. But this is the only way to gain experience and learn how to do everything right.