The decor for walls in the form of imitation under the brick or stone: how to separate the walls of partially or completely, angles or bottom near the panels, sequence, manual. Decorative plaster under brick do it yourself: video lessons of simple solutions pattern under brick

Imitation of decorative brickwork in a modern interior - Photo

In modern design, you can often
Meet interiors with brick masonry indoors. Such an effect
Creates comfort and makes a room more "warm." But for the sake of such an element
It is absolutely inappropriate to do a real brick wall where it is not
on the construction plan. It is expensive, reduces the area of \u200b\u200bthe room as well
Creates an additional burden on the foundation.

Just for such cases there are decorative panels with imitation
Brick masonry. And if the store option for some reason you
Not suitable, and there may be weight them: price, quality, color solution,
form, size, etc., then we can offer you a simple
And an inexpensive way to simulate brick masonry with your own hands. And most
The great advantage of this method is that it does not require
Special skills, such as working with putty and other
Construction mixtures.

To simulate brickwork, you will need:

• cardboard packaging boxes (necessarily thick cardboard)
• pVA glue
• glue thermopystole and rods to it
• paper napkins dense
• brush
• pencil
• rule
• stationery knife or scissors
• paints, varnish

Progress

The surface on which brickwork imitation will be made
(This may be a wall or panel), you need to prepare pre-prepare.
Clean the wall from old wallpaper, if necessary to brew
A special construction primer or a solution of PVA and water and water glue 1 to 2.
If the wall was covered with paint, then the surface to wipe from dust
and degrease.

Imitation of decorative brickwork

A lot of brick varieties. It all depends on what
More will suit your interior. And if the brick color will be
the ability to experiment, then with bricks you need
Decide immediately. The main sizes of bricks can be viewed in the picture

In addition, the type of masonry depends on which side of the brick will
visible. Each party has its own name and will be completely different
Look in the interior.

1 - bed

There are different variants of decorative brickworks: for example, external
The party can fully laid out a bed or spoon, and maybe
Combine different sides of the brick.

In our example, we will imitate a masonry of red bricks, put with a spoon with dimensions of 228 × 65.

On a sheet of thick cardboard (packaging box), we draw the "bricks" of the desired size.

Then cut the sheets on the marked lines using a scissors or a stationery knife and a ruler.

"Masonry" in the interior can be both solid and open to us
Some image. For clarity in this example, we took
Photo from the calendar. In the interior it can be a drawing, photo wallpaper,
stucco, etc.

Place the boundaries of the picture. If the boundaries according to the plan will
Walk under brick decorative masonry, placing a drawing on the wall.
Glue, draw, damp.

Part of the resulting "bricks" cut in half. This is needed for
In order for the laying to go in a chess order and looked realistic.

We start gluitive "bricks" to the surface. This can be done
Heavy wallpaper glue, for example, vinyl. Can be glue pva or any
Another convenient for you in your work. After some experiments
I stopped on this method: PVA construction + glue
Thermopystole. If we consider them separately, then PVA glue is long
dries and immediately does not record bricks, but a glue thermopystole, if
Use without PVA, very quickly spending rods. Therefore, do
So: PVA glue is applied to the entire rectangle, with the exception of themselves
Corners. On the corners, we applied glue from the thermal system. Thermocles immediately
fixes the "brick" in the right place, and the PVA reliably fastens it already
During the day.

Start the laying most convenient from the corner. Fix the first "brick" in the lower left corner.

The next will be fixed at some distance, leaving a place to simulate seam 07-10mm.

The same distance will be departed from above, starting to lay out the second
row. It will begin with halves "Brick" to get masonry
in a checkerboard.

When all rectangles are glued, leave them to dry
At that time, which is indicated in the glue instructions. If it is construction
PVA glue, the time of drying will take about a day.

When the glue dries and "bricks" will be strongly reliable
fixed on the wall or panels, proceed with decoration
Napkins. It is necessary to give the texture of our brick
Masonry and hide the corrugation of packaging cardboard.

Napkins are needed dense, high quality, so that, spacing in the glue, they did not break and not rolled out.

Brush or sponge dense plow glue on top of rectangles.

Fleece the napkin in the hands of folds.

And we apply it to the wall, to the place where glue was applied. Top with a tassel on a napkin again we go with glue.

Gasons between rectangles highlight with a brush or finger.

Thus, we glue the whole wall. Watch that there were folds and well-dedicated gaps - seams between masonry.

Leave to dry another day.

When the glue dries and hardens, proceed to painting.

Color is selected in accordance with the design. In this example
We imitate red bricks. Mixing white, orange, red
And the black paint is seeking similarity with the original brick color.

And cover "bricks". You can make it a tassel, can be sponge, imitating a slightly porous brick structure.

Then we pass the thin brush of the "seams" in the brickwork. Color
The solution also choose to your taste. But most often he has a little
grayish tint.

Remember that the paint after drying becomes lighter than it seems
in liquid state. If in after drying, the color does not suit you,
then the wall can be repainted until it becomes necessary
Tint.

When everything is ready, folds on bricks can be highlighted in a darker or
lighter paint, thus making a little old old
and textures.

The paint of a suitable shade is applied to a dry brush on "bricks".

From above, paint is best covered with varnish to protect the surface from moisture and dust.

Such walls in the interior look very believable and beautiful.
Work is not difficult, it does not need to be professional
builder or finishing, materials are available, and everything can be done
To your liking, picking up colors and forms under the interior.

Decorating residential rooms by natural materials - a kind tradition in interior design. To has long been a favorite stone, forged metal, a tree joined (from the mid-20th century) brick. Becoming a successful mainstream in the segment of the living space arrangement, this material gives the premises of individual aesthetics. The apparent deliberable rudeness of brick masonry in the interior emphasizes the originality of the room, its figurative contrast and immediately attracts attention - the desire to touch the hand involuntarily arises.

White brick in the interior gives the room a special aesthetics

White brick wall favorably shall feature room decoration elements: furniture, textiles, decor. On her background, the color accents sound in a new way and the textured nuances in the interior of each room are revealed. Moreover, it is not only an affordable way of original finishes, but also the possibility of creative use of various functional structures:

• protrusions;

  arched recesses.

Decor elements on a white brick wall background will look like new

Style secrets

Brickwork is a distinctive feature of various style directions.

characteristic and pastel colors;

olive textiles;

other decor elements.

ecodisale elements;

natural materials;

pastel colors;

minimum amount of decor;

white color as a basis (in the northern countries so little sun, so light background out of competition).

With the help of decorative bricks, you can create an accent wall

Terms of use of masonry in the interior

Rule number 1.

Do not be afraid of experiments!

Rule number 2

Guide a sense of measure and knowledge of style.

Rule number 3.

Deciding for an experiment, use a brick finish in reasonable proportions, highlighting it:

the fireplace zone (or zone of the hearth);

separate architectural elements: niches, columns, arches, partitions;

accent wall.

Obtaining decoration walls under the white brick, you can get an uncomfortable cold atmosphere instead of the expected stylish delight.

With this solution, you can allocate specific zones in the interior

What will we do brick from?

There is a large selection of materials for decorative masonry (or imitation). Different in appearance, invoice, price segment they will be able to satisfy any consumer demand.

looping in fresh plaster of a masonry seam, which preserves the shape and size of the brick;

applying a plaster / spacing solution through a stencil, imitating brick textures;

pre-sinking the plane by painting tape (tape) along the lines of the masonry seams, putty (solid layer of the required thickness) is applied to the placed area); The tape (scotch) is removed along with a part of the solution, exposing the natural masonry seam and creating a natural look of brick imitation.

When choosing a material for finishing, the main criterion (after aesthetic and financial) is its functional purpose for a certain type of room. So, in a small hallway, texture wallpapers with imitation are best suitable, and an apron is easily washing white clinker tiles as a kitchen.

For different rooms you need to select the material individually

Designer secrets of white

Living room

In the case of non-standard layout of the room and marching in mind the use of just one plane with a brick surface, try so that it becomes the most fancy on the shape of the wall (with protrusions, niches, deepening). In this case, the masonry under the white brick will adequately emphasize its individuality. If the form of the living room is standard and rectangular, then the main element of the decor will help determine the "necessary" surface: it will be located on it.

The recreation area will also be along such a wall. If there is a fireplace in the living room - then the question of the choice of surface for decorating disappears, since the zone of the hearth and the fireplace is always highlighted by masonry elements.

Brick wall for the living room will be an excellent solution

Bedroom

White brick wall in the bedroom - an excellent design solution. Cause a rough white brick emphasizes the comfort and soft textile: blankets and pillows. On his background, decor elements are successfully displayed: panel, paintings, mirrors, wall lamps.

The advantage of the decorated zone is that with all the "complicity of" clean, white, "sterile-medical" color, such a surface is not homogeneous, but a relief and fault.

White Brick Wall in Bedroom - Excellent Designer Solution

Kitchen

The design of its interior is used for the following purposes.

Montage kitchen apron.
The main requirement (in addition to the aesthetics of design) is an increased functionality, its moisture and heat resistance. Therefore, a white clinker tile is an excellent choice for the kitchen.

Kitchen zoning.
Having a dining area, a white wall background will benefitly emphasize the bright color solutions of individual decorative elements.

Installation Bar rack or kitchen island (if possible area).

When choosing a decorative brick in the kitchen it is worth considering all the nuances of the room

Summing up

Giving the design special originality and exquisite charm, the use of a white brick wall in the interior of the room still has some drawbacks. Of the minuses it is worth noting:

relative high cost of material;

mounting labor cost;

reducing the room space with some types of such a finish.

Such material is durable and combined with all interior styles

And yet undeniable advantages are significantly more. Colored and white brick:

durable;

compatible with many styles in the interior;

particularly durable;

resistant to moisture and temperature fluctuations;

great combined with wood, metal, glass.

Applying this type of finish in the interior should be remembered about the size of the room and seek harmonious interaction with the rest of the design elements.

Video: Brick wall in the interior with their own hands

The imitation of the brick wall can be made independently as a great number of ways that we do not even know from which they start. Let's try to describe the most different techniques and approaches, and readers will choose the appropriate option. In any case, the essence is that when applying plaster is used by a special template made by hand. It is recommended for a typical facing material to add strong binders, such as tile glue. It provides an excellent setting of plaster. In addition, it should not be used quick-release materials. Let's see how the brick wall imitation is performed.

Masonry simulation process

Template for imitation brickwork

A template for imitation of brickwork can be all anything. But, in general, these items can be divided into two classes:

• In the first case, the greater tape is widely used. It is advisable to buy a motok of such a width that coincides with the suture of a typical brick masonry. The facing solution is applied on top of the tape, and then until all this is frozen, the template is withdrawn. It turns out imitation of a brick wall.
• The second type of templates are molds from solid materials. Most often it is wood or plastic. The solution is applied between the guides of the template.

Wall Decor Template

In practice, hybrid variations using the same type of template are also found. In this case, the outer frame is made of wood. Imitation of brickwork dressings is performed stretched inside by painting ribbon. Obviously, such a template cannot be too big. Otherwise, the builders will not only be difficult to move it from place to place, but also there are great difficulties in passing the rugged sections of the wall. Builders come out of the situation as follows:

The builder goes with such a frame and alternately a row for nearby treated the entire surface of the wall until the brick wall is simulated from plaster. Plus such a decision is that it is allowed to work including rapidly frozen solutions, like plaster plaster. During the time the builder will cover a quarter of a quarter-square meter of the wall, it will not have time to dry. Due to this, the master appears great flexibility in choosing a material. At the same time, one serious disadvantage is noticeable. The fact is that when applying a solution over the painting tape, it is necessary to literally extract the frame from under the plaster. This is fraught with a damage. Someone may consider that the wavy areas of the faces imitate the clinker, other masters such an effect will not have to do.

Wall with imitated masonry

That is why you can recommend to collect the entire template of thin rails. Its form will accurately repeat the design already considered in one exception. A painting tape will be replaced by wooden slats. In this case, the slightest slits between the straps can cause some masonry defects. But, as we see, it is not so important. The main thing is firmly consolidated by the planks relative to each other so that the pattern does not walk.

Finally, when working only with painting scotch, without wood planks, the template is created directly on the wall. To do this, an arbitrary area is written by the desired pattern. And immediately we see the first plus of such a decision. The bandage does not have to be regular. We can create both toncho and a longitudinal pattern of masonry. Moreover, it becomes possible to imitate quite precisely rough stones. Previous, pre-created templates, did not allow anything like that. Imitation brick turns out more natural.

Ready Template for Wall

At the same time, the painted scotch has a couple of significant flaws. If the object is large, then there will be much time on the walls of the wall, and a large amount of scotch will be spent. It is completely unacceptable with professional planned development. But individual lovers, the owners of apartments just such a technique may seem simpler. Because it requires a minimum of preparatory work, the process of applying the mixture does not differ in great complexity. The second disadvantage is that the solution should not stick too quickly. Otherwise, it's impossible to exhale rapid tape from under it without damaging a brickwork pattern.

The process of applying plaster imitating brickwork

Consider first the option with painting scotch, as the easiest. In the initial moment you need to put the wall correctly. The easiest way to do this with the help of a ruler and construction level. Also, also to get a rail, quite thick, so that the horizontal builder is easily applied to her end. It will be suitable for the usual construction level with bubbles. The process is simplified by what exactly needs to be done with a rail with only one line. All other horizontals we will postpone from the first up and down with the help of the ruler. As soon as the process is over, you can proceed to imitation of the dressing of the seams. By drawing horizontally, do not forget to work out to postpone the thickness of the seam in addition to the height of bricks.

Wall with brick imitation

The rebirth of the seams is carried out either regularly with the imposition of one brick on another exactly half, or in any order. Thus, perfect imitation of the brick wall in the interior is performed. That is, as it was written above, the master has greater flexibility to select a suitable aesthetic solution. As soon as the wall marking is completed, the process of sticking of the tape begins. First of all, horizontally spread over the entire length. Vertical dressings stitch over top. This ensures the creation of a single template from the painting tape, which is then very simple to get out from under the superimposed construction mixture.

Under the laying of plaster surface is ground. If waterproofing is required, then you must select the appropriate composition in the construction store. The same applies to the fight against fungus and rodents. Next, you need to act according to the instructions on the selected type of plaster. It is categorically recommended to add tile glue to increasing viscosity. Smooth layer of plaster is applied over the template. There is no need to pelt this layer or specifically align it. The waviness of the surface even better imitates brickwork.

While the mixture did not dry, the scotch pattern must be carefully pulled out. At the same time, the seams remain almost completely clean. Surely many want to paint the resulting laying into any color. For this, the composition of the gamma of the terracotta or silicate brick is suitable. After drying the wall, you need to use a special grout for tiles for seams. Color is selected according to its own preferences.

Working with a frame template is much thinner. The process begins from any angle. Usually it is the bottom edge. The plot behind the site builder passes the entire wall. Jumpers with painting ribbon are also found under the layer of plaster. In this case, an additional bonus is that it is possible to mimic the natural color of the seams. This is how it is done. Under the main layer of plaster is applied fine primer loop. The template is applied on top, and then all the work is performed similarly to how it was already above. The tape is neatly removed from under the main plaster, the seams remain almost empty. But in contrast to the previous case, after drying, these places will have the color of the construction mixture. Consequently, it will remain paint only the ends of the bricks.

Decorative Wall

The whole problem is not to stain the seams. It is clear that the easiest way to beat there is a notorious painting ribbon there. But it will not be the cheapest option. That is why both of the present method of making templates we consider imideress. It will be much better to make patterns from wooden plates, and below we present the reasons for which readers can understand all the nuances themselves:

• First, the rails do not enter the layer of plaster. Therefore, the chance to damage the verge of future bricks is minimized. Some can scare the complexity of the blending of plaster on each cell, but in fact the way out of the problem is simple. Quite intermediate rails to make a thickness in the layer of plaster.
• Secondly, the consumption of materials is minimized. We have a single template that is used for all sections of the wall. For problematic and cut places, it is possible to make a smaller pattern separately.

• When painting, we can use the same pattern in order to securely cover all the seams. So, the process of giving the bricks of natural color is simplified to the maximum. Moreover, you can use any color stucco for finishing.
• So that the seams looked naturally, no one forbids us to apply a thin primer gasket under the main layer.

On this, our instructions for imitation of brickwork with the help of plaster are completed.

Imitation of bricks for interior decoration of apartments and houses allows you to make interior unique.

You can arrange the walls with different types of bricks, more precisely from different material.

Imitation of brickwork with their own hands is carried out simply, and the main methods of the design of your apartment will be considered in an innovative way.

Surface preparation

Preparatory stage, before separating the walls of a stone - an important process. Bricks need to put smoothly, applying certain tools and devices, for example, plumbing and level. The laying of material on the wall is carried out only in the horizontal plane, extremely rarely, brick is put vertically. The seams between the bricks are made the same so that the size was one width everywhere. The brick wall itself should not be overwhelmed, in other words perfectly smooth. This often arises difficulties.

First you need to align the walls to lay out an artificial brick on them. For this, the old coating is removed from the walls. If the walls are concrete, from a brick that is old with a large number of defects, as well as from other building materials, plaster works are held. But shuttering is not always convenient to use, some simply will not be able to make a wall for the brick.

To accelerate the preparation of walls under artificial brick, it is recommended to use a simpler preparation method - installation of plasterboard or plywood. Carnate plasterboard sheet can be glued to any wall or on the frame. With the help of GLC, the alignment of the walls will be rapidly, and the plane is ideal for brickwork. When the wall under the artificial brick will be ready, you can move to the immediate design of the apartment or country house.

Bricks from wood

Bricks on the walls can be made of wood. Step-by-step instruction Next:

• Purchase of the material is carried out, in this case, a tree can be used, a chipboard, to create artificial bricks.
• Wooden material should be placed on the desired rectangular pieces, like brick, and cut in size. All parts should be made the same, cardboard is used as a layout.
• The front part of each brick is polished by sandpaper.

• Next, the markup is applied to the wall to get the desired drawing for masonry brick.
• Wooden bricks are laid on the markup. The beginning is carried out from the bottom of the wall, in opposite corners. Each brick is installed with the same interval from each other, so that the seam thickness was correct. The optimal size is 2-4 cm.
• It is necessary to glue to silicone or glue. At the end of the work, a transparent varnish or paint is used, you can apply a gouache if the masonry of the brick was carried out in the children's room. You can decorate with a canister or other paints. To create a specific drawing, it is better to use stencil.

The inner view of such brick will be excellent. Facing material is cheap, with an eco-friendly decorative brick and is distinguished by unusually long-term operation. Outside, of course, use this brick for walls is not recommended.

Decorative plaster bricks

You can imitate brick using gypsum material. Make a gypsum brick is easy, and the result will be similar to what construction sites are offered. The work is carried out in stages, all the details are presented in the table:

Stages of creation:	Description:
Creating a template, forms:	For decoration you need to make bricks for walls on the walls. Brick thickness should be 5-20 mm. If you make a template less, then the brick will easily break, and very thick bricks for the walls, require an increased consumption of plaster and putty for grouting. In addition, a large artificial brick will take the square, and square meters of the room will reduce.
Preparation of the mixture for fill:	The solution is made of dry gypsum, which is divorced in water to the consistency of sour cream and plasticizer (PVA glue) is added. The form for brick is lubricated with a solution of soap so that the fence of artificial bricks for the walls was light. After that, the fill of the solution is carried out. The mixture is leveling a ruler and left for half an hour for pouring. Then the form turns over and gets every brick. Artificial material for walls must be painted. Painting is carried out in 2-3 layers using acrylic paints, and varnish can be applied.
Facing wall bricks:	Make a brick wall imitation with your own hands. The wall is placed on the desired area. The profile is installed below, as the starting line, from where work will be started. The casing is carried out with tile glue that you can buy in any store. The finish of the first row is carried out with the same seams, and then the installation of bricks on the walls is carried out in the chess sequence. Tile glue is applied with a toothed spatula.

You can create a special effect with the help of the edges of the edges of artificial brick, due to this edge there will be torn and uneven, on the wall such design looks beautiful. Keep the decor should be about 3 days, it all depends on the glue used, the instruction can be read on the package.

Tip! Often, a panel of plastic is used to create artificial bricks for the walls, make tiles of foam, clay. Finishing brick, you can apply in bathrooms, except for gypsum, as well as in the corridor or as an outer material for the facade.

Imitation of brickwork (video)

Visually familiarize yourself with the process of creating an artificial laying stone on the wall on the wall, in which the master class is demonstrated:

Formation of seams using painting scotch

This method allows you to imitate the walls of the stone, and work can be carried out with your own hands, directly to the concrete. All major defects are removed on the wall at once, putting a putty in gaps and cracks, pits. In this case, there is no need to smooth the surface to the perfect state, which is great for giving. The underlying condition is to remove strong differences. For work, it will be necessary to use plaster, but it can be replaced with a color putty.

The masonry simulation process is to use paper painting tapes, the ribbon width is necessary such that it will repeat the seam of masonry. A detailed process of work:

• The walls are made on the wall, which will mean lines of seams vertically and horizontal. Vertical seams are shoe in each row of half an artificial finishing material.
• Strips need to draw paint that the color resembles a conventional solution. To do this, it is better not to use gouache, but replace paint with other types.
• If the paint is dried, the stripes of the ribbon horizontally glue, after which the vertical strips are made. Having made the process differently, it will be more difficult to rejuvenate.
• The surface needs to be plastering or putty.

• While the solution is not yet dry, everything is smoothed to the desired state. Some prefer perfect evenness, others want to see wall panels textured.
• After a slight drying of the solution, it is necessary to remove the scotch from the walls, pulling it out of the edges.
• When everything is completely dry, you can build the desired drawing, make stucco, decorate the surface under ancient or choose another finishing finish option.

Tip! Wall under the brick with your own hands will get the most realistic if the plaster is painted into light tones, because after complete drying the color becomes darker. Such a way is suitable if you need to build a masonry on the chimney pipe, oven. The option is suitable to decorate the kitchen, hallway, windows or doorway door. This method is many times cheaper than applying a clinker stone.

Decorative Facing Finish

When the artificial material becomes durable on the wall surface, then the outer sides can be decorated. For this, a sponge or sandpaper is used, and the upper part, artificial image slightly smoothes. This procedure can be missed, if desired. The finishing finish of the artificial wall is to remove the extra parts, the rest of the plaster, which spoils the common picture.

Working depends on the materials used. If the wall made of artificial material turned out to be white and without color, then it is necessary to paint it. Always try to recreate the real stone material, although you can paint in any color that complement the interior design.

To create an unusual effect, the backlight is not needed, during the painting of the artificial wall you need to apply the dye to the material, after a couple of minutes, take the use of another color. Some artificial stones can be painted separately, due to which the styling of the material will stand out, and the house will become a cozy and living room, emphasizing the style.

Based on the style of the house, namely the lighting, color gamut gender, ceiling and other parts, the impressions of the wall of artificial masonry will not be separate, but cumulative. If furniture, niche in the wall, wallpaper, or a fountain plate will not fall into color or by material, then artificial masonry will not complement the design of the house. Artificial laying is recommended to apply in the style of Gothic or Loft, it will be the best option. Some after the artificial masonry wall can draw a picture on the surface or make a bas-relief, to impart effect.

Imitation of a brick wall with your own hands with a photo

Selecting the material for artificial masonry must be borne in mind that the interior in the house may not just change, but also be fringe. It is not recommended to use artificial stone laying on all walls, it is better to decorate individual parts of the walls or only 1-2 walls, on which the picture or clock is hanging. The rest of the walls are better to stick the roll of wallpaper or plastic panels.

Before artificial masonry is carried out, it will be necessary to completely visualize the stone walls. Any of the presented materials can be used to decorate the walls. The presented methods are used not only for walls, but also for cladding certain items, for example, artificial masonry are made on furniture, vases. Patterns are created under the antique for retro styles, as in the photo:

It does not look great for the wall, but the selection of the opening of the artificial masonry, which can be on the door or window. Imitation of masonry on the wall is done, leaving the standard technology, applying original solutions. Artificial stone laying on the walls perfectly complements the kitchen, namely the working area. Also, it is suitable for zoning premises to highlight certain places.

Photo gallery of finished work

The brick wall is relevant among the various styles of the interior, but when it is unrealistic, you can smear in any way. In this article we will analyze how you can draw a brick wall, without resorting to the services of artists. Three methods will be presented for which simple materials will be required, some patience and accuracy.

What it looks like

Painting the wall under the brick, perhaps the cheapest way to simulate it. In addition, it is practical. If the wallpaper can be swap, can spoil pets, then it will not happen from the painting. Unlike wallpaper, painting do not have to skip, if you get tired - you can simply repaint the wall.

Drawn brickwork looks, of course, not as impressive as the original, but also suits any designer solution. A visual example of this in the photo below.

• On the harvested and dry background, it is necessary to make a stencil with a narrow painting tape - it will be a masonry seams. Bricks can vary depending on your preferences. If at this stage does not be lazy and glue the molar scotch exactly, it will take it in the worst hour of 3 hours, depending on the size of the wall.
• Next, the entire wall is painted in a brick color with a roller, but you can use the paintopult. Give the paint to dry carefully, then you can remove the scotch.
• In order not to get confused during the markup, you can separate every brick in half - this is already a masonry vertical seam for bricks to the level above, and the brick itself is marked with a passion with a simple pencil.
• As a result, you will have a neat imitation of brickwork.

Method 3: With the help of foam rubber

Porpalone pieces are desirable to take a few, in case the first strongly solidifies paint. The form and size should be like a real brick, that is, a rectangular shape, about 25 cm in width and 6.5 cm in height.

• Stamp from foam rubber carcass in a pre-harvested tray with paint. Do not forget to remove the surplus paint from the stamp, they can spoil the whole composition.
• Then attach the foam rubber to the wall, thereby leaving the imprint.
• Thus, leave stamps in the form of bricks throughout the desired area of \u200b\u200bthe wall. Try to leave the same gap between bricks.

Output of volume and texture

This is perhaps the most important part of the finish - without this stage, the work done will not look like the most naturally and naturally. In addition, the methods for decorating bricks are suitable for all three ways to imitate masonry.

• For greater realistic brickwork, add additional shades. To give the visibility of the volume, the upper face can be lazy, and the lower on the contrary - darkened.
• To give a wall a bit of "negligence", you can add various strokes and strokes with a sponge, thereby creating an antique effect.
• In order for the drawing of the masonry seams to see how "deeper," it should be tested with a thin tassel, a slightly darker shade.
• When you apply the drawing, misses are quite possible in the form of random lines and unnecessary spots. You will need to delete them immediately, with the help of ordinary water, because acrylic paint dries very quickly.

Even without having any artistic skills. You will be able to paint the wall under the brick, the main thing is to not allow rude mistakes.

We hope that the article was useful to you. Leave your questions and reviews in the comments below.

Previous