Polycarbonate veranda attached to the house: options and do-it-yourself installation. Convenient canopies attached to the house, made of polycarbonate, beautiful awnings, photos of various designs and their cost What can be attached to a private house

The process of creating structures from polycarbonate is popular today, due to the aesthetics and ease of installation. Canopies can be:

mobile - easy to move around the site. They are installed above the barbecue area;
autonomous - for example, it is a separately located canopy over the pool, parking lot, greenhouse, outbuildings, gazebos.
Adjacent - this is an extension to the building, for example, a veranda or terrace, a porch.

These structures come in various forms. They may be closed or open. In the first case, the side walls are glued with panels, decorated with a lattice, blockhouse, clapboard, or curtained with thick curtains.

The canopy is a structure of vertical pillars with a roof. The frame is made of metal, wood, less often brick and stone.

Advantages of polycarbonate awnings

The general characteristics of polycarbonate are known to many. This transparent type of polymer has a high specific gravity. Thanks to this, polycarbonate is resistant to high and low temperatures. Before starting work with polycarbonate, it is worth understanding the concepts between a monolithic and cellular type of material.

The structure of cellular polycarbonate differs in heat-insulating properties, and the material is more plastic. Monolithic material is characterized by the following properties:

strength;
small specific gravity;
absorption of the sun's rays.

In this case, it is possible to use matte or transparent sheets.

Often the choice in favor of polycarbonate is due to a design decision, however the general pros are always the same:

ease of care;
attractive design and various colors;
duration of operation;
simplicity of design;
affordable price.

Varieties of polycarbonate canopies

Among the huge range of canopies, I would like to highlight a few of the main ones:

single slope. This is the simplest design, and therefore the most affordable. It is a canopy with one inclined slope. The design is easy to make, and it takes a little time.
Multi-slope. The labor-intensive manufacturing process of such a design explains its higher cost. This implies the presence of several slopes on one structure, both arcuate and straight. If desired, the canopy is given an original appearance. Experts note that the more slopes a canopy has, the more expensive its cost.
Arched. It has a complex type of arched or arched frame. This adds to the aesthetics of the design. If you decide to settle for such a solution, you must count on the additional costs of creating a curved structure. The surface of the canopy requires a little more material than other designs.
Difficult. This type of awning is one of the most expensive. It implies the presence of several solutions from the options listed above. It takes a long time to design, and it takes more time and effort to manufacture.

The subtleties of choosing polycarbonate

In order not to make a serious mistake and purchase high-quality material for a canopy, several nuances should be considered.

When choosing the optimal thickness of the material, it is necessary to take into account the level of the bend of the roof, the possible load. More durable construction helps to make a frequent crate.

for the manufacture of a greenhouse complex, cellular polycarbonate with a thickness of 4 mm should be purchased;
an indicator of 10 mm is suitable for designing a noise-protective structure and special lights;
material with a thickness of 6 - 8 mm is ideal for sheds and roofs of various summer cottages;
polycarbonate 16 mm thick is optimal for parking lots and wide areas.

Making canopies from polycarbonate - photo

In addition to practical characteristics, aesthetic nuances must be taken into account when choosing polycarbonate. To begin with, they are determined with the color scheme of the material. Polycarbonate today can be of any color with varying degrees of transparency.

Experts advise taking into account the purpose of the structure and the general design of the suburban area. When a canopy is required to cover the pool, the most successful color scheme is emerald or blue. At the same time, this design is not suitable for the design of a trade pavilion, since the visibility of the goods is deteriorating.

For the greenhouse, transparent polycarbonate is used, which transmits daylight well. However, if we are talking about the design of a recreation area, such a visor is not able to provide protection from the bright sun. For these designs, it is preferable to use dark polycarbonate sheets of brown or blue shades. These colors absorb light better than others.
You can be sure that a polycarbonate canopy will become a favorite place on the site for relatives and guests. It will decorate the territory and allow you to create a secluded corner on it.

If a specialist undertakes to develop a cottage project, then it necessarily provides a place for a recreation area. As such, it can be a patio, a gazebo or a canopy attached to the house. The presence of this kind of construction on the adjacent territory not only makes the site more aesthetic, but also adds useful living space.

2 Types and purpose of attached canopies

3 Project development

4 Preparatory work

5 Installation of a polycarbonate canopy attached to the house

5.1 Canopy sheathing
5.2 Roof installation

6 Conclusion

Materials for the construction of a canopy

Most often, for the manufacture of the frame of an attached structure, a wooden beam or profiled steel pipe. At the same time, such traditional materials as brick, stone, asbestos-cement pipe filled with reinforced concrete can act as an alternative. The final choice is determined by the purpose of the canopy and the load that the frame will experience.

Considering that the canopy attached to the house is closely adjacent to the wall, it has to take on the load that the snow rolling down from the roof exerts. And this extension will be able to cope with such great pressure only if it has a solid foundation.

Most often, as a roofing material for an extension, they are used slate, profiled sheet, galvanized iron. Today, there are many other options on the construction market, among which a polycarbonate canopy attached to the house is of particular interest. If you look at the photos of such structures, it becomes clear that fiberglass forms excellent compositions with frames made of other materials. Similar canopies are created on the basis of sheets of a cellular structure having a thickness of 6-8 mm.

Polycarbonate has the following advantages that have made it a popular material for creating canopies:

In addition to the above, this transparent polymer does not create difficulties in processing. It is easy to drill, cut with a saw, grinder and electric jigsaw.

If you are thinking of making a canopy, it is recommended to use polycarbonate for it, which has UV protection. All other types of this thermoplastic are not recommended, because otherwise, as a result of exposure to the sun, it will soon take on a cloudy appearance and lose its original flexibility.

Types and purpose of attached canopies

All awnings offered today that can be attached to the house can be classified into two categories:

Visors on consoles;
Awnings installed on the main supports.

One of the features of cantilever models is that they can be of unlimited length, as a result of which such a structure can be installed along the facade of a building without joints. At the same time, they have width restrictions: this parameter cannot exceed 2 m. This is not done by chance, but for safety reasons: with such a width, the canopy will be securely fixed to the wall and the wind will not be able to pull it out. First of all, these structures are designed to protect doors from the sun and precipitation. At the same time, if you add forged or carved visors to them, then such a combination will help to give an original look to the facade.

With the help of supporting canopies, you can solve many different tasks:

Polycarbonate is a unique material that can be used to make roofs of various shapes, including single-pitched, double-pitched, pyramidal, arched, concave and convex. If desired, the owner can modify the design of the canopy through the use of colored or tinted fiberglass.

Project development

If you have a desire to add such an extension as a canopy to your country house, then it will not hurt you to familiarize yourself with the photo of this design first. In order not to make a mistake with the choice of a canopy, it is necessary consider the following parameters:

After that, they begin to draw up a drawing of a polycarbonate canopy attached to the house, photos here will not be superfluous. It should display the actual dimensions: height, length and depth of the structure. Based on this information, the required amount of materials for the manufacture of the frame and roof will be calculated.

For example, in order to make a carport for parking a car, the structure must have the following average dimensions:

250 x 500 cm - for vehicles whose length does not exceed 4 m.
350 x 660 cm - for SUVs and cars whose length exceeds 4 m.

When designing a canopy attached to the house, you need to have a photo at hand. But at the same time, it must be taken into account that its dimensions should allow the car with a load to drive under the canopy freely. If the roof has a height of more than 230 cm, be prepared for the fact that precipitation will constantly fall on the transport. You can solve this problem as follows: for this you need to install the roof at a different angle.

Preparatory work

After all the above questions are resolved, you can go directly for site preparation where a polycarbonate canopy will be erected. First, the site must be marked out, after which it must be cleared of foreign objects, including trees and shrubs. Next, you need to remove the sod to the depth of root germination. After finishing the work on cleaning the site, it must be leveled with a layer of sand or fine gravel. In conclusion, you need to carefully tamp the site.

At the next stage, it is necessary to create supports for a canopy attached to the house. For this, pits are drilled, which should have the following dimensions: depth - 50-60 cm, diameter - 20 cm. During this operation, it is necessary to take care of the possibility of laying the cable under the lighting fixtures.

When choosing the distance at which the supports will be placed in relation to each other, it is necessary to focus on the area of \u200b\u200bthe extension, the material from which the frame will be made, as well as the weight of the roof. For more massive structures, it will be necessary to increase the frequency of post placement. Usually it is enough to arrange them in increments of 1-1.5 m. Having created a similar base at first, you will not have to deal with its docking with the main foundation of a residential building.

After the holes are dug, they need to fill with a bucket of rubble, and then put vertical racks there, which are poured with concrete. Be sure to make sure that all the pillars are located strictly according to the level. In this case, you can do otherwise: embedded parts with brackets are inserted into the created pits, which are attached to the concrete solution. And only after that they install the pillars themselves.

It is also necessary to pay attention to the material: the tree must be treated with an antiseptic, it can also be covered with drying oil or painted in any desired color. To install a canopy, be sure to use dry lumber, from which you need to remove the skin, if any, otherwise there is a risk that woodworms will appear under the bark pretty soon.

If you are arranging a canopy for a house that is located in a lowland, then it is necessary to perform additional waterproofing of the ends of the wooden supports. This can be done by wrapping them with a polyethylene or roofing felt shirt, or by pouring them with hot bitumen.

Special processing is required metal racks to which a primer containing zinc phosphate is applied. Although this time-consuming operation can be avoided if a galvanized or aluminum profile is used instead of the indicated supports.

Waiting for the moment when the concrete in the pits hardens, you can start making flooring for the canopy. There are several methods for solving this problem:

Creation of a concrete screed;
Laying boards or paving slabs;
The device of a sand or gravel cushion.

Installation of a polycarbonate canopy attached to the house

When the time required for the setting of concrete comes up, it usually takes 10-15 days, we proceed to the assembly of the structure. The first step is to install several brackets to the outer wall of the house, to which it is planned to attach a canopy. Subsequently, a load-bearing cross beam will be installed on them.

Canopy crate

After that they start for top trim. To do this, you need to fasten the ends of the concreted vertical pillars to the transverse beam, after which they are connected to each other. This operation is performed using parallel stacked profiles. If you have to deal with a steel frame, then welding is used to connect the parts. In the event that the frame is made of wood, the connection is made using steel corners. After creating the welds, they need to be processed, applied a layer of primer and painted.

Installation of rafters is carried out to the crossbars, and they should be located at a distance of 60 m from each other. In order to fasten them to the carrier beam, which is installed to the wall, steel corners are used. Lathing installation it is carried out in such a way that it lies across the rafters, and the step that must be maintained here must be 30 cm. Self-tapping screws are used as fasteners. In the manufacture of the frame, a bar of various diameters is used:

Racks - 120 × 120 mm.
Cross beams - 100 × 100 mm.
Rafters - 70 × 70 mm.
Lathing - 50 × 50 mm.

If the frame is constructed from a metal profile, then it will have the following diameter:

Racks - 40 × 60 mm.
Rafters and lathing - 30 × 50 mm.

Roof installation

To begin with, you will have to prepare sheets of fiberglass, which must be cut in accordance with the calculated dimensions, after which they are mounted on the crate. But first you need to make holes in them for fasteners. When performing this operation, you need to pay attention to the fact that the plastic cells look down. In this case, the resulting condensate will drain freely. It is recommended to perform this work using self-tapping screws equipped with a rubber thermal washer. For fixing sheets use an H-profile.

Conclusion

To equip a recreation area or protect the entrance from precipitation, you can use such modern material as polycarbonate. With its help, you can make a reliable canopy that will not only decorate the building, but will also effectively cope with its task for a long time. Any person who does not even have special skills can make a canopy attached to a polycarbonate house.

Due to the fact that it is quite simple to work with this material, even with the help of available tools and materials it is possible to make an extension that will create an additional comfort zone in the house.

Immediately after the construction of the house, and sometimes "before" the question arises with parking. It is not always possible to build a major garage, but putting a roof on poles - a canopy - is already easier and cheaper. The carport can be a freestanding structure. Then it is placed in the yard, as a rule, not far from the entrance gate or garage. The second option is attached to the house, when one or more sides of the roof rests on the wall of the building. In terms of functionality, both options are equivalent, just everyone chooses based on personal requirements and preferences.

Dimensions

Since the dimensions of cars can vary greatly, in each case the optimal dimensions are determined depending on the available car.

The height is usually around 2.5 meters. This is more than enough even for an SUV with a loaded trunk. And to determine the length and width of the canopy, at least a meter is added to the external dimensions of the machine. Agree, it is quite enough if there is a distance of half a meter to the pillars.

But to protect against precipitation, it is better to make the roof overhangs longer: they will also close from oblique rain and snow.

When determining the size of the canopy for two cars, the distance between the rear-view mirrors is taken to be 50 cm. The same amount is considered to the pillars. And the length of the canopy is determined by the longest car.

Frame materials

Basically, wood is used for supports - a beam or a log, a metal pipe of a round or rectangular section. Sometimes the supporting columns are made of brick or stone. They are more massive, attract more attention, therefore they must fit into the style of the building that is nearby.

There are other options when the bottom of the support column is made of brick, and the top is made of wood or metal. And in this case, everything is determined by the style of the house and the site. You should not make brick supports if there are restrictions on the size of the site: they are quite massive and take up a decent amount of space.

All materials (except bricks) are processed before use. Wood is necessarily covered with flame retardants (reducing the combustibility of the material). Then it is impregnated with compounds that will protect it from damage by woodworms, as well as from all weather conditions.

Its implementation

Particular attention should be paid to the processing of wood, which will be buried in the ground. It can be impregnated with special compounds for wood in contact with the ground (for example, Senezh Ultra and its analogues). Impregnation showed itself well in working out. The ends of the poles that will be buried are immersed in a container with working off for a couple of days. After drying, they can be used without additional measures. 10 years is enough.

The second option is to pour a concrete pillar into the ground, and mount a mortgage plate, shoe or hairpin into it, to which a wooden beam is then attached.

Metal poles are cleaned of rust, covered with a primer. After welding, the seams are additionally processed and everything is covered with paint in two layers. The second is applied after the first coat of paint has dried to a “tack-free” state.

Roof types (with drawings and dimensions)

The most economical and simplest is a shed roof. Usually it is used if the carport is attached to the house: this is the easiest way to organize a normal connection to the wall.

They make a shed roof for free-standing canopies. In regions with little snowy winters, it is possible to make a roof without a slope, in those where there is a lot of snow, a slope of at least 8-10 ° is required. In this case, the lower side is made from the south or east: so that there is more shade. Also in this case, on the south side, you can sew up the canopy on the side (or plant tall plants there).

If a canopy is made of polycarbonate, then the roof is vaulted. It is also optimal in terms of precipitation and is easily implemented due to the flexibility of this material.

A more complex gable roof. If made of metal, it has a relatively simple structure.

In the case of a wooden canopy under a gable roof, the system is multi-component.

roofing material

If the carport is attached to the house, it makes sense to make its roof from the same material. For soft types of roofs (flexible tiles, ondulin, etc.), a solid crate is required, for hard ones, a sparse one, and the step is chosen depending on wind and snow loads in the region, also focusing on the recommendations of roofing material manufacturers.

If complete shading is not required, polycarbonate can be used. By the way, it is the most popular material in recent times. It is only necessary to choose it correctly: take a multi-chamber one, which has at least three layers of plastic and two rows of cells. Under such a canopy made of polycarbonate, even on a sunny day, it is not hot.

Also, the degree of heating depends on the color. See the technical specifications and choose the one with more sunlight absorption. Transparent ones are needed for greenhouses to warm plants. For canopies, on the contrary, you need polycarbonate with low light transmission.

How to lay out a platform

The easiest and most inexpensive way to make a platform under a carport is to fill it with gravel. To do this, it will be necessary to remove the sod, dig in the curb, pour rubble and compact it well using tamping platforms. Then the platform will be rigid and ruts will not form.

Compacted gravel is a good cover for a car park

Recently, sites paved with paving slabs or paving stones are more popular. They have a more attractive appearance, but their device is more expensive. Preparation also begins: first, the soil is removed. But the pit is made with a depth of about 20-25 cm. Crushed stone is poured into the bottom, which is also well rammed. Then it is desirable to spread a layer on the rubble. This is a non-woven material that will prevent the sand that will be poured from above from waking up and mixing with gravel. Also, geotextiles redistribute the load more evenly, preventing the base from sinking under the wheels of a car (it is used in road construction). A layer of sand is already poured on it, which is also rammed. Paving slabs, clinker bricks, cobblestones and other similar materials are laid in the sand.

In the middle in terms of costs is a concrete platform. The base is also prepared from rammed rubble. Wooden planks are laid on it at a distance of 1 m, which are set to a level or with a slight slope to drain water. These strips serve as beacons during pouring, and then play the role of damper joints, compensating for the thermal expansion of concrete. With this structure, cracks appear less frequently.

A metal mesh of galvanized wire is laid between the planks. You can, of course, stainless steel, but it is expensive. The thickness of the wire is 3-4 mm, the cell is 10 * 10 cm. It is poured from above. The thickness of the concrete layer is 7-10 cm.

Do-it-yourself canopy attached to the house (photo report)

It was decided to attach a shed to the house, under which to hide your favorite equipment - a car and a boat. First, with the help of a motor drill, they dug holes 1.5 m deep - below the freezing depth.

We inserted sleeves from waterproofing, a frame made of 10 mm bar with welded mortgages, poured concrete.

The installation step of the pillars is 2 meters.

When the concrete had set, the poles and the top trim were installed. They are sanded and treated with protective impregnation. To prevent the frame from moving, they fixed it with what it was - aluminum corners. The junction of the racks and strapping was reinforced with metal plates.

The pillars are screwed to the "heels"

A support board was nailed to the wall of the house. Roof beams were attached to it (board 50-200 cm). The slope turned out to be small, about 9 °, but it is enough. Small cuts were made in the beams to fit the size of the beam - for emphasis, the edges were cut off to get an even overhang.

The beams were attached to the strapping with nails obliquely, 2 pieces on each side.

The beams on the wall are fixed on U-shaped metal plates.

The rafter system is assembled - the beams were installed with a small step - 40 cm, they were made from a board 50 * 200 mm.

OSB was attached to the rafters on top. Roofing material - soft tiles. Underneath it needs a solid crate.

A board was nailed on the side between the posts: for greater rigidity and so that the rain would less wet the site.

The sidewall was sewn up with a board - so that the rain would get less

Laid soft tiles. It turned out - at least dance.

Now there's competition in the parking lot.

How to make a canopy for polycarbonate (photo report)

Used materials:

professional pipe
- for racks 80*80 14.6 m;
- for arches 50 * 25 - 4 pcs. 6 m + 50 * 25 - 10 pcs. 6 m each for spacers;
sand concrete - 3 bags of 40 kg.
crushed stone - 4 bags of 25 kg.
minium - 3 cans of 1 liter.

The canopy was made over the already finished track. The pillars were buried in the gap between the curb and the fence. It turned out that the supports of the canopy were placed near the fence posts. It was decided to use them when setting the level: they attached them with anchors so as not to suffer when pouring.

The metal pillars of the racks were dug into the ground at a depth of 1.2 m, covered with crushed stone, and poured with concrete. When the concrete had set, the top trim was welded on.

After that, the production of farms began. First, profiles with the required radius were bent on a pipe bender (rise at the highest point 1.2 m). After the assembly of the "designer" began.

Clamps were useful, they fastened parts so that they would not move during work. Fixed to the first farm, so that everything was done exactly. There were a lot of clamps

When all the trusses were ready, they were cleaned, sanded to white metal, then primed and painted twice. Then the acrobatics began. It is necessary to install heavy trusses on poles, set them vertically, without knocking down the diagonal.

As soon as it was possible to set it correctly, they quickly grabbed it by welding, leaving a thorough welding of the seams “for later”, after the final check: everything should be on the same level.

A miracle happened, everything turned out to be almost on the same level. A small difference of a few millimeters is not taken into account.

Now we weld a crate from a 50 * 25 mm profile pipe for polycarbonate. we place them along the long side of the canopy. The installation step is 0.8 m.

It remains to attach polycarbonate. It is attached to self-tapping screws through special thermal washers (sold in the same place as polycarbonate). Two sheets are connected using special profiles. They are detachable and non-detachable. One-piece ones are cheaper, but then you can’t do anything else from this polycarbonate. So we used detachable ones.

It is also necessary to close the edges of all sheets, otherwise dust, midges will fill inside, then moisture will appear due to evaporation, followed by mold. And the view of the coating will be deplorable. Therefore, we install special plugs on the edges.

Varieties and scope

It will perfectly replace metal, glass and wood. Not a single suburban construction is complete without it.

On the shelves of the store you can find several types of products:

Monolithic or cast

It has a beautiful appearance, reminiscent of colorless or colored glass, but surpasses it in strength. Used in structures with heavy loads.

Profiled

The shape is in the form of a wave. It has the same characteristics as the first type (monolithic). Easy to install roofing, as the size of the sheets is the same as the metal of the tiles.

Cellular

The product is very common in commercial and private construction. Its light weight and low price make it affordable. While working with it, an assistant is not required, and designs can be made of any complexity.

A polycarbonate canopy can be found in many places:

in a canopy above the balcony.
in a swimming pool.
in the manga.
in the car.
in the gazebo and patio.
above the porch;

Advantages and disadvantages

Advantages of polycarbonate panels:

Elastic and flexible material, can be used for all types of roofing.
Outperforms plastic and glass.
Not subject to sudden temperature changes.
Light weight.
Sufficient degree of transparency.
Not subject to mechanical stress.
Easy to install.

Minuses:

High price.
No resistance to abrasive influences.
Expanding from the heat.

Drawing

A simple canopy scheme

Let's say you decide to make a carport. It can be a free-standing building or a supporting structure. When developing a drawing, we take into account the class of the car. Further, 100 cm are added to its dimensions on each side - this will be the size of the site.

Now you can move on to the design of the canopy. We take into account the slope of the upper surface. Drawing for a machine that has dimensions of 1.6 x 4.2 m. The site will have a size of 2.6 x 5 m.

The roof can have a different shape and meet some requirements of wind and snow loads. When making a drawing, we apply all the dimensions of the elements that are involved in the construction.

Let's give an example of the simplest typical canopy.

To install polycarbonate sheets with a thickness of less than 8 mm, a step of 600-700 mm is sufficient.

It will require:

cellular polycarbonate, 8 mm thick;
runs with a profile pipe 40x25x2 and 50x25x2 mm;
arched truss (30x30x2 mm);
beam (60x60x3 mm);
support posts (60x60x3 mm);
heels for racks (30x30x6 mm);

All communications must be completed in advance. The site can be covered with a concreted area, tiles.

The canopy above the door is available to every novice home owner or builder. To do this, draw a straight or curved sheet with a frame. Fastening will be carried out directly above the door. Dimensions 1400x1000x300 mm.

What is it needed for?

A designed and drawn up drawing will save you time in the future:

Firstly, drawing up a competent document, will make it possible to choose the right location and design.
Secondly, you can determine the amount of material, thereby saving money.
Third, the choice of the original appearance, which will be in harmony with the landscape design.

What data should contain:

Basic structural elements with drawings.
Sketch of the entire structure.
Calculated data for roof snow load.
Estimated roof sail data.
Calculation of the strength of trusses and supports.
Design and estimate documentation. All types of materials and their cost are described in detail here.

How to create correctly:

Do not forget about additional dimensions, for example, for a car.
Bear in mind the prevailing wind when calculating.
Consider a direct driveway to the shed, no turns.
Access from all sides.
An accessible and simple drawing (bearing structures and a frame made of a profile pipe).
Minimum cost.
To create a harmonious project, taking into account the closely standing house and the garden plot.

Types and design features

First of all, the place of construction is determined.

The project can be done in several ways:

Take advantage of the internet.
Get service from professionals.
Do it yourself.
Buy a finished structure, with a proposed drawing.

It depends on this what the support will be:

Console. It is a small canopy in front of the entrance to the house. Supported by mortgages or mensols.
Consulting and support. Also an extension to the house, only rests on mortgages or brackets. And they are on the wall.
Beam-support. One side of the structure focuses on a horizontal beam in the wall, the other stands on supports.
Separate. When the roof is supported on the support posts.

Canopy construction technology

Structure connection scheme: 1 - Decorative cover TP-03; 2 - Profile TP-01; 3 – Seal TPU-01; 4 - Polycarbonate; 5 - Self-adhesive seal; 6 - Self-tapping screw; 7 - anti-dust tape; 8 - End profile UP; 9 - Substructure element.

We are preparing a place for a canopy.
We mark the points for the support posts. We make wells 50 cm deep, manually or with a drill.
We install supports and fill them with mortar. We are waiting for the complete drying of the solution for about three days. So that the surface does not crack, pour water over it for three days.
Next, we carry out the execution of the upper strapping, where we use an electric welding machine.
We fix the transverse elements of the structure.
The upper part can be a horizontal, arched, gable or single slope design.
Welded seams are cleaned and sanded.
We do the primer and painting of the metal frame.
The next step is to mount the polycarbonate panels.

Required materials and tools:

on supporting pillars, a profile with a square section 10 × 10, 8 × 8, 6 × 6 cm;
for runs, we take a profile pipe with a section of 6 × 4 or 6 × 6 cm;
for the crate - 4 × 4 cm (profile pipe);
arched structure;
polycarbonate is more reliable to take 10 mm, as it has excellent characteristics and an attractive appearance, it is easy to use;
press washers and self-tapping screws;
crushed stone, mortar (sand and cement);
screwdriver;
drill, knife;
a circular saw;

Fastening the canopy racks to embedded elements

Walkthrough:

We make blanks from polycarbonate plates using a circular saw. Moreover, do not forget to make allowances on sheets of 10-15 cm in length. During fastening, we open the protective film in those places where the fastening will be carried out, we do not touch the rest. Since along it we lead the fastener landmark. We place the panels with the film on the outside. It is from this side that they are protected from ultraviolet radiation.
We place the docking profile at a distance equal to decomposed polycarbonate.
We fix the sheets with self-tapping screws, for which we pre-drill, we make holes, a little more (2 mm) than the size of the press washers. Next, insert the washer, then twist the screws and close them with protective caps. We also cover the edge of the sheet with a protective tape to prevent dirt from entering.
The process is repeatable until all panels are in place.

The height of the structure depends on the slope of the canopy. The greater the slope, the taller the structure.
If a metal frame is chosen, profiles with a square section of 6 × 6 - 10 × 10 cm are perfect here.
Do not forget to make a sandy "cushion" under the supports.
To bend the panel, use a profile that is notched and bent into the desired shape.
The optimal building height is considered to be 220-250 cm if it is used for a car.
The thickness for various forms of structures is chosen in different units. For example, with a large area and a sloping roof shape, choose a thickness of 10 mm. In arched structures, 8 mm is considered sufficient thickness. Small canopies - 6. Horizontal structures - 16 mm, so that it can withstand the load in the snowy season.
When using cellular polycarbonate, remember that any alterations with it are quite complicated.

In the hot summer months, one really wants to hide in the shade from the scorching sun, but often the lack of trees near a new private house does not allow this. In winter, the owners suffer from snow drifts in the yard, which they constantly have to clean on their own or with the help of hired workers. A canopy to the house will help to get rid of such problems completely or at least partially.

Ready-made metal profile canopy attached to the house

A canopy is a structure located, as a rule, near the building. The main load of the weight can be distributed between the wall of a private house and the supports, or fall entirely on the constructed supports. In fact, a canopy is a roof without walls or attached to a wall.

Sheds suit to solve a number of specific tasks:

Shading. In the hot season, suspended structures are designed to create shade in a recreational area, a parking area or storage areas for any stocks.
Rain protection. I don’t want to get caught in the rain during a picnic and get wet, and it will remain cleaner.
Snow protection. You will be able to spend your personal time less often cleaning snow drifts in the yard, in front of the porch and cleaning the car after a snowfall.

As you can see, the canopy is very convenient.

An example of a canopy for a house made of polycarbonate and metal poles

Thanks to the development of construction, the design can be not only functional, but also very beautiful.
Among the hinged structures, several main types are most widely used:

metal,
wooden,
forged,
stone.

Polycarbonate, slate, profiled sheet or other roofing material can be used as a covering material.
The shape of the canopies can also be different. Today, there are also multi-level decorative canopies, and extensions to the house in the form of a continuation of the roof, and simple hinged structures.

Visors

In a special group, it is worth highlighting a canopy over a porch or window - a visor. This is usually a small structure with two pillars attached to the wall or ground in front of the porch.
Typically, visors are made in the form of a welded frame made of metal or wood and coated with polycarbonate or corrugated board.

It looks like a visor for a house made of corrugated board

Entrance groups can also be decorated with a forged frame, then the visor looks especially elegant and beautiful.

Material selection

Before making a canopy to the house, you should decide on the choice of basic materials for construction. Each of them has its pros and cons.

wooden structures

Canopies made of wood are not uncommon today. For their construction, a 10x10 beam is usually used as supports, a smaller beam and boards for roof sheathing. A decorative canopy can also be decorated with a railing, which also increases the strength of the structure. Among the advantages of wooden canopies are the following:

Of the minuses, it should be mentioned that wood is a flammable material, so you need to watch out for sources of fire nearby. The location of the barbecue near such a structure is unacceptable.
Also, the tree can rot under the influence of excess moisture. To prevent this from happening, special coatings are used: primers, varnishes and paints.

Metal constructions

Metal structures are pipes welded or otherwise fixed together, covered with some kind of roofing material.
As supports, a round or shaped pipe of a sufficiently large diameter (at least 10 cm) and a metal thickness of at least 2 mm is usually used.

An example of a metal canopy for a car park

The benefits of these canopies include:

High structural strength (provided by welding the elements together).
If you have a welding machine and certain skills, you can make the design of the canopy yourself. This will also reduce the final cost of the product, since the price for the services of a welder is quite high.
The profile pipe bends quite easily with the help of a special device - a pipe bender. Due to this, it is possible to produce rather elegant designs that are attractive in appearance.
A metal structure will be lighter than a stone or wooden one. The metal does not absorb moisture and does not become heavier after heavy rains or snowmelt.

However, the metal is susceptible to corrosion. Periodic painting of the surface of the frame will help to cope with this problem. Before applying a layer of paint, the metal surface must be primed.

Forged structures

Such designs, as a rule, represent the basis of a metal frame, decorated with forged elements. They are welded to the frame, providing not only an attractive appearance, but also increasing the strength of the structure. Forged canopies have several advantages:

look easy and elegant;
strong and durable (forged products have been standing near various ancient castles for centuries, without losing their external attractiveness and pristine strength);
relatively not expensive (among the elite designs of canopies, forged can be considered quite inexpensive compared, for example, with a canopy with stone supports);
design flexibility is another advantage. Due to the increase in load, the product will not break, as it could happen with a wooden one, but only slightly bend.

An example of a canopy to the house using forged elements

Compared to wooden or simple metal structures, a wrought iron canopy will be much more expensive. However, it is worth it when it comes to prestige and creating a representative image of the owner of a private house or a successful company.

Most likely, to build a forged canopy, you will have to resort to the help of a specialist. Good blacksmiths can be counted on one hand, but if you find such a master, you will be satisfied with his work for the rest of your life.

Constructions made of stone

Only very respectable citizens can afford to make stone structures the basis for a canopy. But such a contribution of funds is justified in some cases.

Stone is an almost eternal material. He is not afraid of either heat, or cold, or temperature changes, so the design will stand for many years.
Stone structures look very respectable and beautiful.
The high strength of the canopy frame allows you not to worry about its reinforcement with additional elements.

Stone is undoubtedly a very expensive material. Therefore, many people lay a metal structure at the base of the frame, and on top of it they veneer the surface with a finishing material that imitates the surface of natural stone. Building a canopy using this approach will significantly reduce the cost and speed up the process of building a structure, and the appearance will remain at the highest level.

Preparing for installation

In order to make a canopy in front of the house, you need to prepare for the construction process. For convenience, it is worth dividing the entire preparation process into several stages.

Location selection

It should be remembered that if you are going to make a canopy in front of the porch or just against the wall, then you will need to install fewer supports than if you were doing a free-standing canopy.

The original canopy to the house made of wood

It is necessary to take this into account, because an increase in the number of supports entails an increase in total costs: for the construction of the foundation, for the purchase of material for the supports.

If you can’t attach a canopy to the wall in any way, you should choose a place where it will be convenient to dig holes for the foundation (without plantings and asphalt or sidewalk paths). You need to try to find a free place between the already ennobled territory and a private house, if possible, and only then deal with the arrangement in the yard.

Purchase of materials

Before purchasing material, it is worth carefully calculating how much you will need in the end. For this, possible designs of structures are considered. If you wish and have the ability, you can prepare projects yourself, but remember that this requires certain engineering knowledge. Otherwise, the design may be flimsy and will not last long.

Canopy for a cottage from a metal profile

If there is no self-confidence, it is better to play it safe and order projects in a special construction organization. The price of the issue is high, but health and life are more expensive.

Having chosen the base material, supports, additional connecting elements, fasteners are purchased. For wood and metal surfaces, it will be necessary to purchase a certain type of primer and paint (or varnish) to protect the frame from the harmful effects of sunlight and moisture. For the foundation, you will need sand, crushed stone and concrete, as well as reinforcement if the base is solid. For welding, you will need electrodes, for cutting parts - disks for a grinder, and for tying the frame together - corners, screws, bolts, and so on.

When choosing a cover for a canopy, many opt for canopies made of polycarbonate or corrugated board. Each of these materials has its own advantages.

Ready-made canopy for a house made of wood and polycarbonate

So, polycarbonate canopies look lighter and more elegant due to transparency and a high degree of flexibility. Structures made of corrugated board are much stronger, they are not as afraid of hail as polycarbonate products.

On the other hand, you can buy polycarbonate with a higher density (8 or 10 mm) to minimize the likelihood of penetration of the material.

However, corrugated board awnings are opaque and provide better protection from the sun in hot weather. Professional sheet, besides, it will cost less. When choosing between these two materials, it is necessary to weigh the pros and cons.

When purchasing material according to calculations, it is always worth adding an additional 10% of the total volume to the required amount. Practice shows that there are always unforeseen costs of materials due to errors in projects or difficulties that have arisen.

Tool preparation

The list of tools required for the job may vary depending on the selected canopy material.
During construction, you may need:

for pouring the foundation - shovels, concrete mixer, wheelbarrow;
for even installation of supports and frame elements - level, square;
for welding metal structures - a welding machine;
for a canopy made of metal or wood - a screwdriver, a grinder or a circular saw, a drill (especially if you plan to tie the structure to the wall).

You may also need a stepladder or high ladder to work at heights. If you have to lift a solid welded metal frame structure upstairs, you will have to resort to the services of a manipulator.