The hot tub hums and doesn't work. The jacuzzi tub does not turn on. When Do You Need a Hot Tub Repair?

) is a device that is very necessary for health, helping not only to relax and get rid of the feeling of fatigue after a hard day's work, but also to compensate for the full supply of vital energy.

When taking a bath, it is possible to choose one of the types of massage:

air massage (air bubbles);
hydromassage (streams of water);
turbopool (combined alternative).

The main goal of hydromassage is to achieve muscle relaxation and deep relaxation. In these devices relaxation effect is achieved by entering through the nozzles of water or air under the intended pressure. The nozzle holes are located in the most "hot" zones - parallel to the spine, in the lumbar zone, in the legs.

The device for hydromassage is equipped with rather complex equipment, which must be looked after and systematically turned on. preventive work. Despite regular procedures, problems still occur from time to time.

Complex equipment and causes of breakdowns

The most common cause of malfunction is blockage. Its characteristic principle is the difficult drainage of water.

The equipment has a negative impact violation of the integrity of the surface products - chips, cracks and scratches.

Moreover, it is considered too poor water quality, also leads to the formation of lime scale in the tooling pipes. Chemicals are another reason why hot tubs fail. In accordance with the rules of operation do not use detergents when the hydromassage is running, because chemicals, making their way into the nozzles, take them out of working condition. According to this, washing in a jacuzzi with the use of shampoos and soaps is possible only when the hydromassage system is turned off.

In some situations, the breakdown factor is the failure of one or multiple equipment nodes. Often, pumps (for a hot tub), aero compressors and water collectors break down.

Gallery: jacuzzi (25 photos)

Basic rules for repair work

If the warranty period has come to an end, and your product is out of order, do not rush to call the wizard. The fact is that it is possible to repair a jacuzzi do it yourself.

All that is needed for this is to calculate the cause. Most often, blockages and other malfunctions are subjected to cartridge. In this case, it is enough to clean it, however, replacement may also be required.

Not very strong water pressure, proves that system filters are dirty. To check the power of pressure, you need to open all the taps in the house.

When replacing a broken part, you must purchase a similar replacement part from the hot tub manufacturer. This is due to the fact that analogues from other companies can differ significantly in various ways, that is, their use can lead to a malfunction of the entire hydromassage system.

As a rule, the bath ceases to function due to blockages. In order to eliminate them, as well as prevent them, it is poured into a specially designated hole bath cleaning detergent(hydromassage). After passing through all the pipes, it destroys all the dirt, directing it into the sewer. This saves the device from destruction.

In devices without a disinfection system, you can use cleaning tablet and throw it into the water during the operation of the bath. In areas with poor water quality, a similar procedure should be carried out at least once every two months. In order to prevent blockages, it must be remembered that hair, threads and other foreign matter should not get into the Jacuzzi device, as over time this will invariably lead to clogging.

In addition, we must not forget that for cleaning acrylic products it is necessary to use only specialized solutions and tablets.

Modern products for hydromassage are made from acrylic using resins and fiberglass. The thickness of such bathtubs reaches 7-9 mm, the choice of the method of repair work is based on the calculation of the depth of damage to the product. To find the reasons, find out how your bath was made, in other words, evaluate the cut of its side. The body of the whirlpool with a millimeter acrylic coating is made from plastic, otherwise it is made from a single sheet by molding.

For repairs you will need:

Elimination of small cracks

In most cases, innovative hot tubs equipped with all necessary material to troubleshoot many types of problems. Let's say you have a jacuzzi made by spraying or casting, then in the kit for its repair there will be a special composition for this type of breakdown.

In order to remove cracks enough watery acrylic, we note if the product was cast from a sheet. However, repairs should be carried out in strict accordance with the established technology. Initially, the crack should be slightly expanded so that the solution can soak the inside. Then, using fine-grained sandpaper, grind its edges. In the future, prepare the mixture, and apply to the carefully treated degreased area.

Remove excess hardened consistency from the surface of the product with sandpaper. Upon completion of the repair work, it is desirable to grind this area.

For through cracks more complex repairs are needed. First you need to prevent the possibility of crack expansion. To do this, drill holes on both sides of the crack with a thin drill, then completely degrease the surface. The next step will be adhesive tape, which must be attached to the outside of the product, and then resume the task described above.

Mixer replacement

The basis for changing the mixer will be cartridge damage. Initially, this element should be cleaned. If this does not lead to the desired result, then you need to replace it. In this case, you need to buy one hundred percent of the same cartridge. Before installing a new component, it is necessary to clean the landing "nest", remove scale and wipe dry.

Nozzle failure

Sometimes the root cause of the jacuzzi failure is a breakdown, or rather, nozzle clogging. For such a situation, a decrease in the power of water pressure is characteristic. To fix it, you need to roll up the cap and gently clean the inner surface with a soft cloth and water from accumulated dirt.

The owners of hot tubs often face the following problem: whirlpool does not turn on. If the bathtub has a pneumatic button for turning on the hydromassage function, then the replacement will not be difficult, since the removal and connection work is inexpensive. The cost of a pneumatic button varies from 600 rubles and more. It’s quite another matter when an electronic panel is introduced, then, accordingly, repairs will be expensive. However, it is worth noting that if you turn to professionals, the service will be at the highest level, and they will be able to change the remote control to a pneumatic button.

The air and water pump is the heart of the whirlpool bath, which is formed from special alloys and is completely safe for humans. It's easy to identify the root cause of pump problems, but it is desirable to diagnose the mechanism. In particular, you can control the water supply without leaving the bathroom using small levers or a remote control. If you have an exclusive model of baths, then you can add a small fraction of the massage programs to the integrated computer. However, if repairing a hot tub with your own hands is not within your power, and even more so repairing a hot tub pump, then you should contact the masters who know their job!

Thus, do-it-yourself Jacuzzi repair is not a very laborious process, but it still requires a responsible attitude.

Like any complex technical device that operates in difficult conditions, a hot tub requires careful care and timely maintenance, and if any element fails, repairs may be required. It is best if the maintenance and repair of hot tubs is carried out by competent specialists, but in some cases, some simple operations can be performed independently.

Symptoms

In case of incorrect operation, check the control panel

If the hydromassage does not work when turned on, and no sounds are heard, do not panic and first of all check whether the bath is connected to the mains.

Tip: The hot tub outlet should be located in a convenient location that is protected from water, and the tub's power cord should be firmly plugged into the outlet.

If, with a positive test result, the hot tub control does not respond to pressing the buttons, a deeper diagnosis of the problem is necessary. In most cases, microcontroller equipment is in good order, and all malfunctions arise from poor contact or damage to the supply wires.

What can break?

The cause of the breakdown may be lime deposits in the pump or filter

The elements of the equipment installed in the hot tub have a certain service life, after which they may fail. A breakdown can happen earlier, depending on many factors, which will entail the need for a forced replacement:

First of all, as in any device that works with the aquatic environment, lime deposits can be deposited in the components of the hydromassage bath, preventing the normal operation of the system, and since it is very difficult to get to them, after a while the elements fail and it may be necessary their replacement. Therefore, all devices from well-known manufacturers are equipped with a filtration system at least or a deployed water treatment system in elite models;
A hot tub filter can also need repair, especially when owners can't keep up with the replacement filter elements. The filter warns about its "disease" in advance, by reducing the intensity of the massage and the louder operation of the pump;

Frequent breakdowns are clogged nozzles

Following the filter, a pump is installed that creates a flow of fluid through the nozzles. If the pressure created by the pump is not enough, then there will be no massage. In some models, a whirlpool bath compressor is installed, which creates excess air pressure, which, mixing with a jet of water in the nozzles, creates the effect of a natural geyser. If it is noticed that the pump or compressor is buzzing, but there is no jet of water from the nozzles, you must immediately turn off the bathtub from the outlet and call the repairman;
Hydromassage jets (see photo above) are directing devices with a certain throughput that create massage jets that are so pleasant for the body. If even one nozzle is clogged, the operation of the entire hydromassage system is disrupted due to the redistribution of water pressure. Delaying the repair of the nozzle can cause a chain reaction of breakdowns and a multiple increase in the cost of repairs;
And finally, the bath bowl itself can break, not to mention the numerous accessories designed for convenient water procedures.

How to repair?

First of all, remove the cover and carry out a visual inspection of the equipment.

First, let's look at how you can repair a jacuzzi tub that has minor or larger damage.

If there are just scratches on the bath bowl, they can even be repaired by polishing yourself, and deeper damage with the help of special repair kits containing all the necessary components. Acrylic jacuzzi bathtub repair will be performed with high quality, if you carefully follow the instructions and do not ignore the operations indicated in it, then the bathtub will shine with its original brilliance and whiteness.

In the event that the bowl is cracked and the hot tub is leaking, a more complex repair will be required, requiring special equipment and materials. In this case, it is better to invite a competent specialist. It is unlikely that the user will have a special soldering station for welding plastics and the necessary adhesives, and improperly performed repairs can only worsen the situation and incur additional costs.

Can parts be repaired?

In some cases, whirlpool bath equipment can be serviced and repaired, and with good quality, but sometimes only replacement is required:

If the hot tub does not turn on, if there is no equipment recall for any manipulations with the control panel, you can independently check the presence of voltage at the output terminals of the control devices and the integrity of the fuse, while observing the rules of elementary safety precautions. In the event of a power failure, it is necessary to replace the power cable, having previously turned off the equipment from the outlet;
If the whirlpool bath pump or compressor makes suspicious sounds, then repairs can only be carried out by qualified personnel, sometimes even in a workshop, so you need to call the master, and do not turn on the equipment until he arrives;

In case of problems with electrical equipment, it is better to call the master

The jets for hot tubs most often fail as the most wear-prone elements. The flow of water with air bubbles wears out the nozzle, and the dirt deposited on the nozzle elements, when dried, turns into solid deposits that prevent the passage of water. A variety of jets for hot tubs, with all their external dissimilarity, and there are more than five types of them, can be quite easily disassembled and cleaned from dirt. If cleaning does not work, and parts are visibly damaged, then replacement will be required. It should be understood that jets for whirlpool baths differ in functionality. Hot tub water jets and air jets are used to create separate water and air jets. These spare parts are installed in different parts of the bowl and connected to the respective systems, while the combined models combine two devices in one housing;
When purchasing spare parts for bathtubs with hydromassage, it is necessary to choose only those that are designed for a specific bathtub model, and it is better if these are products from the same manufacturer. In this case, compliance with the installation dimensions and parameters of the bath nozzle and the service life of the installed product are guaranteed;
You can replace the nozzles yourself, since this operation is not very difficult. Before replacing the nozzles in the bathroom, make sure that it is disconnected from the mains, and the inlet water taps are closed;
The control elements installed on the whirlpool baths are divided into electronic-sensory devices or mechanical control using a special button. The pneumatic switch for hot tubs, like all pneumatic systems, is very capricious, and the slightest jamming of the valve leads to switch failure. You can disassemble and clean the valve yourself, but if you don’t have instructions at hand, you need to remember or photograph the position of the connected hoses and the location of the button parts in order to properly assemble the device. It is best to replace the switch, since the pneumatic button for hot tubs is not such an expensive device to repair a failed unit without confidence in the quality of the repair;

You can replace the nozzle yourself

The electronic-touch controller for a hot tub cannot be repaired by yourself. Here replacement or intervention of the master is necessary, which is very often limited by the manufacturer. It is simply not possible to program a microcontroller without a factory program;
One of the important elements of the system, for all its seeming simplicity, are hoses for hot tubs, damage to which can cause a lot of unpleasant emotions, spilling large amounts of water and damaging the pump. When inspecting hoses during maintenance, it is imperative to replace products that have cracks and damage. Hoses are those components for hot tubs that you should not save on and buy cheap products from obscure manufacturers.

Tip: I would like to note in a separate line the spots in the bathroom installed on some, especially expensive models, filling the water space with soft light. If you have a choice, it is better to give preference to modern LED lamps with programmable colors due to their durability.

For long-term trouble-free operation of any model of hot tub, the following conditions must always be met:

Maintenance of hot tubs is the same mandatory operation as brushing your teeth in the morning and evening, and it must be performed at least as often as indicated by the manufacturer;
If you have knowledge, skills and some simple tools, you can do the diagnostics and repair of the hot tub with your own hands, without repairing complex components;
Accessories for whirlpool baths must match the model and, if possible, be with a bathtub from the same manufacturer;

In the absence of confidence that the repair of Jacuzzi baths will be carried out independently, it is better to invite service center specialists who will carry out repairs as soon as possible and who have all the necessary spare parts for hot tubs of any manufacturer.

The hot tub is a very useful and pleasant invention. However, in case of breakdowns, the hot tub needs to be repaired. Sometimes you can do it yourself, without the involvement of specialists.

1

A hot tub is a special plumbing fixture, the use of which is very beneficial for the human body. It has a positive effect on all systems, on the skin, tissues, blood vessels, joints. This is done by the action of jets of water and air, creating bubbles. Directed by their impact on the human body and has a beneficial effect.

Hydromassage bath

However, over time, various malfunctions appear in the operation of the jacuzzi, the mechanisms break down. This is especially true for Russian apartments, where the water quality leaves much to be desired.

Often, repairs can be done with your own hands, without the involvement of specialists. This is especially true for problems such as clogged drains, clogged nozzles, and breakdown of the mixer.

2

Most often, problems such as the appearance of cracks on the bowl, breakage of the mixer and nozzles occur. With such malfunctions, it is easy to repair the jacuzzi with your own hands.

Repair of the bowl depends on the method of its manufacture. As a rule, sanitary ware is made of acrylic. If the bowl is made by casting (the top layer is made of plastic), then the repair is carried out using a gel coat. Often with such baths in the set are repair kits. In this case, the crack is closed with the proposed compositions.

Liquid acrylic is used to repair molded plumbing. In both cases, proceed as follows. First, the crack is slightly expanded so that the composition penetrates well deep into the defect. Next, the damage is ground and degreased, a composition with a slide is poured into the crack. In the process of solidification, the mixture will settle and be flush with the entire surface. After solidification, excess material is removed, the surface is polished.

Repair molded sanitary ware with liquid acrylic

The mixer breaks, as a rule, due to the failure of the cartridge. To repair it, you need to clean it. If this does not give positive results, then the cartridge must be replaced with a new one. When installing a new element, carefully process the mixer socket, removing scale and wiping it dry.

Faulty operation of the nozzles is manifested in the fact that water flows out in a thin stream. Sometimes the reason for this is low pressure, which means that you should first check the operation of other taps in the house. If everything is functioning normally in the water supply system, then the nozzles should be cleaned. To do this, unscrew the cap, use a cloth to remove all dirt and scale.

The jacuzzi can stop working due to blockages. Some hot tub models have a disinfection system. In this case, a cleaning agent is poured into the special holes. It passes through all pipes and channels, cleaning the internal cavity from dirt. If such a system is not provided for in the bath, then during its operation several cleaning tablets should be thrown into the water. When choosing such tablets, it must be taken into account that they must be suitable for acrylic surfaces.

If the pump is broken, it is better to seek the help of specialists. The hydromassage system is quite complex, and even the slightest defect can lead to serious consequences.

3

To reduce the risk of breakage of hot tubs, various preventive measures should be taken.

To do this, you need to use different means to care for the jacuzzi. When choosing them, it is recommended to choose compounds that are safe for the human body. Cleaners and disinfectants should be used strictly in accordance with the instructions for use.

Every day you need to rinse the surface of the bathtub with water and wipe it with a soft cloth. Do not use abrasive cleaners, hard sponges or fluffy fabrics. The hot tub should be disinfected and deep cleaned monthly. The procedure is performed as follows. The bath is filled with water that rises several centimeters above the nozzles. A special disinfectant dissolves in the water, then the pumps turn on for a few minutes. After turning them off, you must wait about 20-25 minutes and drain the water. The procedure should be carried out again, then remove and clean the filters, install them in place and wipe the plumbing with a soft cloth.

Deep Cleaning Jacuzzi

At least once a year, the hot tub should be cleaned with a 7% acetic acid solution. Such a composition effectively cleans all surfaces from limescale, while it is completely safe for humans and for acrylic. Cleaning is carried out as follows. The bath is filled with water, acetic acid is added to it. The pumps are turned on for 30-60 seconds, the water is left for 10-12 hours, then the bath is emptied. The procedure must be repeated one more time, then rinse the jacuzzi with water and wipe it off.

Sometimes cleaning needs to be done more frequently. The frequency depends on the quality of the water. In addition, it is not allowed to get hair, threads, various fibers and other foreign bodies into the jacuzzi. All these elements lead to clogging of the plumbing system. Chemicals entering the jacuzzi also have a negative effect. Therefore, soaps and shampoos must not be used when the hydromassage system is on.

By following all these tips, you can significantly increase the life of your hot tub.

And a few more tips from experts. If the jacuzzi has stopped working, you should check the power supply, whether it is carried out correctly. In addition, the voltage value must correspond to the value specified in the operating instructions.

With a weak jet in the nozzles, you need to check the water pressure in the water supply. To do this, open the faucet in the kitchen or bathroom.

When replacing a broken part, you must purchase a replacement part from the hot tub manufacturer. This is due to the fact that analogues from other companies may differ in various parameters. Their use may damage the hydromassage system.

Hot tubs are becoming more and more popular due to their ability to improve the health of a person, as well as fill its user with new forces.

Baths with several types of massage are on the market: aero, hydro and turbopool. Each of the technologies differs in the principle of operation. Aeromassage releases air bubbles, hydromassage releases streams of water, and turbopool is a combined technology during which both water and air act on the body.

Despite the fact that we live in a world in which technology is quite well developed, no technique can last forever. The reason for this may be non-compliance with the conditions of use or the banal wear of the main elements.

Problems have not bypassed the device for hydromassage, which is driven by a complex mechanism. Even despite regular care and timely preventive maintenance, the hot tub can fail. You can get rid of some problems on your own, while others will have to seek help from specialists, but the most common causes of breakdowns should be known to every owner of hot tubs, as well as those who are just thinking about purchasing such a product.

The main reasons for the failure of hydromassage equipment:

clogging of the water intake - occurs most often, especially if the intake holes are not periodically cleaned;
cracks, chips and scratches on the surface of the device;
poor water quality - especially important in our country, since the water contains a large number of elements that contribute to the formation of plaque;
chemically active substances - it is forbidden to use various detergents during the operation of hydromassage equipment, so even shampoo and soap, if the compressors are turned on, will have to be abandoned;
contamination of the system filters - most often it is enough to clean them, but in especially severe cases they will need to be completely replaced;
failure of the leading components of hydromassage equipment - a malfunction of the system can be caused by a failure of compressors, water collectors and pumps.

Do-it-yourself hot tub repair rules

The correct determination of the cause of the breakdown is half the repair performed, and if you are confident in your abilities, then you can not rush to call the master. If a particular part needs to be replaced to fix the problem, you need to make sure that it is compatible with your Jacuzzi or hot tub model.

If you are not sure of the true cause of the breakdown and that you can eliminate it without outside intervention, seek help from specialists.

How to Clear Clogs in Your Hot Tub and Jacuzzi

One of the main reasons why a bath may stop working is the clogging of both the entire system and its individual elements. Some products have a built-in special system designed for disinfection, elimination of blockages, as well as their prevention. A cleaning agent is poured into a special hole, which, passing through the joints, helps to remove various kinds of debris.

If your bathtub or jacuzzi does not have such a system, you can use special cleaning tablets that are placed in the water while the hydromassage system is operating.

In those regions where the water quality is far from the best, such a procedure should be carried out at least once, every two months of operation.

Cleaning products are good, but it is better to help keep various debris out of the work openings, so you need to keep a close eye on this. Hair clings especially well to the inner surfaces of the pipes, and then collects on itself almost all the rest of the small debris that enters the drain holes or nozzles.

Cracks and chips

All modern whirlpool tubs are made from acrylic reinforced with third-party materials such as fiberglass and special resins. The base can be ordinary plastic, on which the same acrylic is applied with a millimeter layer. To find out what materials were used to make a bathtub or jacuzzi, just look at its side cut.

The main tools and materials that may be needed for repair work: liquid acrylic, sandpaper, adhesive tape, a grinder with a grinding attachment and a drill with thin drills.

There are two types of cracks and chips that can be encountered during operation: shallow and through.

Repair of shallow cracks

To complete this procedure, most manufacturers pre-complete their products with a special repair kit. Small cracks on products that were made by casting can be repaired with liquid acrylic alone.

To repair the damage, you need to initially expand the chip itself with sandpaper, degrease it, prepare an acrylic mixture, apply it to the damaged area and remove the excess, using sandpaper again. At the end of these steps, the work surface must be sanded.

Removing through damage

To get rid of through chips, you have to work a little more. As a rule, a through crack grows in two directions, which are determined by the farthest, opposite edges from each other.

The first thing to do is to prevent a further increase in size. To do this, using a thin drill, we drill holes on both sides, at the most extreme points of the crack. Only after that we proceed to degreasing the surface.

Using adhesive tape, you need to completely seal the hole and proceed to the process of processing with liquid acrylic, which is performed in exactly the same way as when working with shallow cracks and chips.

Mixer replacement

- this is the mechanism in the bathroom that breaks down most often, regardless of whether it is located directly on the body of the jacuzzi itself or is displayed separately. Single lever faucets have become very popular in recent years as they are quite easy to use and repair.

The main reason for the breakdown of this device is the wear of the cartridge, which is responsible for supplying and adjusting water. The internal structure is so simple that even the fair sex can handle its replacement.

The only thing you need to take care of is to purchase a cartridge in advance, which will be exactly the same as the previous one. To be completely sure that you are buying what you need, take a worn part with you to the market, which will serve as an image.

Repair/replacement of defective hot tub and jacuzzi jets

Another of the most common reasons for the termination of the normal operation of the hydromassage device is clogging of the nozzles. To get rid of the debris that has accumulated inside, you need to carefully twist the outer cap and clean the hole with a rag and water.

Rules of care, cleanliness

Proper care of hot tubs and jacuzzis is a guarantee that the product will serve you faithfully for a very long time. The modern market offers a huge number of various care products for complex hydromassage equipment.

When choosing them, you need to focus on several factors: the presence of a disinfection system in your device, the presence of aggressive components in the composition that can destroy, as well as the level of environmental safety for humans.

When using certain products, you must strictly follow the instructions on the packaging. If this is not done, it is easy to disable the entire system and then the usual cleaning is not enough. In addition, some components can cause allergic reactions in some people.

Once a month, you need to carry out a number of preventive measures that will help maintain the hot tub in good condition:

Fill the container to a level that will be a couple of centimeters above the nozzles.
Dissolve the disinfectant in water according to the instructions.
Turn on the pumps for a few minutes (5 minutes is enough) and turn them off.
Wait 20 minutes and flush the water.
Items 1-4 are carried out 2 times.
After the second time, you need to clean the filters from debris and install them in their rightful place.

Once a year, a deep cleaning of the bath is carried out using an acetic acid solution with a content of active elements at the level of 7%. This solution will not damage the acrylic surface.

If you have a hot tub or jacuzzi in your house, you should remember one thing - timely care and periodic prevention is the best way to deal with possible problems, which will help save not only money, but also nerves.

One of the hot tub jets is leaking. Leak at the junction of the D32 hose and the nozzle itself. There are NO firms specializing in the repair of hydromassage vans in our city (Kirov).
The question is how to eliminate this leak and using what materials, given that the choice of the latter can be very limited.
Thank you.

Not only materials are required to fix a hose leak, but the experience of the craftsman plays an equally important role.

The cause of the leak is a violation of the bonding technology.

In general, 2 types of connections can be used for bathtubs: PVC pipes (rigid) and PVC hoses (in the form of PVC tape twisted into a spiral). Consider the case of spiral hose, as it is more common.

To solve your problem in the most minimal composition, you will need:

1. Adhesive for PVC pipes. For example Tangit.

2. A small piece of 32mm hose.

3. Repair sleeve according to the diameter of the hose, i.e. 32mm.

4. Tools: pliers, sharp knife, thinner 646.

Depending on the convenience of the location of the defective adhesive, it may be necessary to remove the nozzle from the side of the tub.

It's easy to do. After removing the decorative ring, unscrew the nozzle fastening nut (white large threaded ring).

Sometimes this may not be necessary.

Now the main thing. Cut a 32mm hose at a distance of about 2-3cm from the faulty gluing. The piece of hose remaining in the nozzle must be pulled out. To do this, cut it with a knife or side cutters along the seam of the spiral. Then take firmly with pliers the edge of the hose, and begin to dissolve it in a spiral. In this case, you need to monitor the applied force, and pull so that the tape does not break. Of course, you can try and try to remove the hose without cutting it, sometimes if the quality of the gluing is very poor (especially if the bathtub is new), it succeeds and you just need to glue it back. You can try to swing the hose in different directions. When doing this, it is important not to damage the hole in the nozzle.

After the hole in the nozzle has been freed, we proceed to restore the connection.

We cut the free hose so that the repair coupling is removed. The cut on the hose must be even and at right angles to the axis of the pipe. Before gluing, degrease the outer surface of the hose and coupling (nozzle) with a solvent. We apply glue with a brush first into the hole, then onto the hose. Distribute evenly over the surface. We don’t regret glue, but we don’t need to apply a lot either. Immediately after application, insert the hose into the fitting until it stops. In the same way, we glue the fitted piece of hose through the coupling. When working with glue, its vapors are very toxic, so you should try not to breathe it and ventilate the room.

According to the situation, you first need to figure out in what sequence to glue it to make it more convenient.

Glue polymerizes within 1.5 hours. After pour water and check the bath for a leak.

Glue, couplings and hose can be ordered in the shop section.

Leak in the nozzle of the g/m bath

Apparently you were lucky, and the leak was insignificant, or it was the air supply hose to the nozzle, or the pump inlet pipe (50 mm) (working at P The issue is chem. adhesive reaction on PVC fitting and hose. None of the silicones known to us enter into a chemical interaction with PVC. (And the glue even “melts” it a little). Therefore, coating the hose is a temporary measure, because. it does not eliminate the cause of the leak (not sizing).
We came across bathtubs that flowed at 70% of the joints. Of course, this is a production defect, and it consisted in the fact that the hoses supplied to the bathtub manufacturer did not react with Tangit glue. They popped out easily with little effort.
Above is a radical method that guarantees a 100% result.